Application of EPR-MOGA in computing the liquefaction-induced settlement of a building subjected to seismic shake

Accurate prediction of the liquefaction-induced settlement (\({S}_{\mathrm{lc}}\)) is an essential requirement for a good design of buildings resting on liquefiable ground and subjected to seismic shake. However, prediction of the \({S}_{\mathrm{lc}}\) is not straightforward process and it requires advanced soil models and calibrated soil parameters that are not readily available for designers/practitioners. In addition, the available empirical models to estimate the \({S}_{\mathrm{lc}}\) have been developed using either classical regression analysis or multivariate adaptive regression splines and such techniques produce complicated models. Also, these empirical models have been developed utilizing results of numerical modelling. To overcome these limitations, novel model has been developed in this paper utilizing robust regression analysis driven by artificial intelligence called the evolutionary polynomial regression analysis. The new model has been developed using centrifuge results (real laboratory measurements) and can be easily used to accurately estimate the liquefaction induced settlement. The developed model scored a mean absolute error, root mean square error, mean, standard deviation of the predicted to measured values, coefficient of determination, \(a20 - \mathrm{index}\), and EPR coefficient of determination of 2.12 cm, 2.84 cm, 1.06, 0.19, 0.98, 0.77, and 97%, respectively, for the learning data and 1.73 cm, 3.31 cm, 0.99, 0.17, 0.97, 0.75, and 97%, respectively, for the examination data. The developed model has also been used in a parametric study to provide an insight into the sensitivity of the \({S}_{\mathrm{lc}}\) to the foundation width, building height, pressure applied on the foundation, thickness and relative density of the liquefiable layer, and earthquake intensity. The results obtained from the parametric study are reasonable and in agreement with previous studies in the literature. Thus, the developed model can be employed to optimize designs and to reduce design costs as it does not require complicated analyses and/or expensive computational facilities.

     

Signal Integrity: Fault Modeling and Testing in High-Speed SoCs

As we approach 100 nm technology the interconnect issues are becoming one of the main concerns in the testing of gigahertz system-on-chips. Voltage distortion (noise) and delay violations (skew) contribute to the signal integrity loss and ultimately functional error, performance degradation and reliability problems. In this paper, we first define a model for integrity faults on the high-speed interconnects. Then, we present a BIST-based test methodology that includes two special cells to detect and measure noise and skew occurring on the interconnects of the gigahertz system-on-chips. Using an inexpensive test architecture the integrity information accumulated by these special cells can be scanned out for final test and reliability analysis.     

Mechanical behavior of 30–50 nm thick aluminum films under uniaxial tension

We present uniaxial tensile test results for 30–50 nm thick freestanding aluminum films. Young’s modulus and ductility were found to decrease monotonically with grain size. Reverse Hall–Petch behavior was observed with no appreciable room temperature creep. Non-linear elasticity with small irreversible deformation was observed for 50 nm thick specimens.     

The influence of raw material characteristics on the industrial pelletizing process and pellet quality

Industrial pelletizing of sawdust was carried out as a designed experiment in the factors: sawdust moisture content, fractions of fresh pine, stored pine and spruce. The process parameters and response variables were energy consumption, pellet flow rate, pellet bulk density, durability and moisture content. The final data consisted of twelve industrial scale runs. Because of the many response variables, data evaluation was by principal component analysis of a 12 × 9 data matrix. The two principal component model showed a clustering of samples, with a good reproducibility of the center points. It also showed a positive correlation of energy consumption, bulk density and durability all negatively correlated to flow rate and moisture content. The stored pine was more related to high durability and bulk density. The role of the spruce fraction was unclear. The design matrix, augmented with the process parameters was a 12 × 6 matrix. Partial least squares regression showed excellent results for pellet moisture content and bulk density. The model for durability was promising. A 12 × 21 data matrix of fatty- and resin acid concentrations measured by GC–MS showed the differences between fresh and stored pine very clearly. The influence of the spruce fraction was less clear. However, the influence of the fatty- and resin acids on the pelletizing process could not be confirmed, indicating that other differences between fresh and stored pine sawdust have to be investigated. This work shows that it is possible to design the pelletizing process for moderate energy consumption and high pellet quality.     

Study of the morphology and mechanical properties of polypropylene composites with silica or rice‐husk

The mechanical, morphological behavior and water absorption characteristics of polypropylene (PP) and silica, or PP and rice‐husk, composites have been studied. The silica used in this study as filler was a commercial type produced from soluble glass or rice husks. The compatibilizing effect of PP grafted with monomethyl itaconate (PP‐g‐MMI) and/or with vinyltriethoxysilane (PP‐g‐VTES) as polar monomers on the mechanical properties and water absorption was also investigated. In general, a high loading of the studied fillers in the polymer matrix increases the stiffness and the water absorption capacity. This effect is more noticeable in the tensile modulus of the PP/silica composite with PP‐g‐VTES as compatibilizer. However, the increase of the rice‐husk charge as a natural filler in the PP matrix decreases the stiffness, and in the presence of PP‐g‐MMI as compatibilizer in PP/rice‐husk, the tensile modulus and water absorption of the composite were improved. The better adhesion and phase continuity in the PP/silica and PP/rice‐husk composites with different compatibilizers was confirmed by the morphological study. Copyright © 2004 Society of Chemical Industry     

Enteric viral infections of calves and passive immunity

At least eight viruses have been identified, four within the last 5 yr, that produce diarrhea and pathological intestinal lesions in experimentally inoculated calves. Coronavirus and rotavirus frequently are associated with the neonatal calf diarrhea syndrome, but the etiologic role of the newly identified viruses is undefined. All diarrheal viruses replicate within small intestinal epithelial cells, resulting in variable degrees of villous atrophy. Immunity against these viral infections, therefore, must be directed toward protection of the susceptible intestinal epithelial cells. Because most of these viral infections occur in calves less than 3 wk of age, passive lactogenic immunity within the gut lumen plays an important role in protection. This report reviews methods of boosting rotavirus antibody responses in bovine mammary secretions and analyses of passive and active immunity in calves supplemented with colostrum and challenged by rotavirus. Results indicate rotavirus immunoglobulin G1 antibodies in colostrum and milk were elevated after intramuscular and intramammary vaccination of pregnant cows with an Ohio Agricultural Research and Development Center rotavirus vaccine but not after intramuscular immunization with a commercial rota-coronavirus vaccine. Feeding colostrum from intramuscular plus intramammary immunized cows to newborn calves challenged by rotavirus prevented diarrhea and shedding of rotavirus.     

Multi-objective optimization of a hatchback rear end utilizing fractional factorial design algorithm

Air flow has significant effects on fuel consumption, performance, and comfort. Decreasing drag coefficient enhances fuel consumption and vehicle performance. Moreover, omitting or reducing the power of aerodynamic noise sources provides passengers comfort. In this paper, optimization of a hatchback rear end is conducted considering drag and aerodynamic noise objectives. To this end, five geometrical parameters of the hatchback rear end are chosen as design variables in two levels. Numerical simulation is applied to survey air flow features around the models in the wind tunnel. To reduce the number of runs, fraction factorial design algorithm is applied to generate layout of the simulations which decreased the number of case studies to half. Main and interaction effects of these factors on drag coefficient and acoustic power of the rear end source are derived using analysis of variance. Optimum level for each parameter is chosen considering simultaneous drag and noise goals. Finally, characteristics of air flow and acoustic power around optimum model are discussed.

     

Vortex structure in high-T c ceramic superconductors

We consider penetration of magnetic flux in the rare earth ceramic superconductors within the framework of a generalized Ginzburg-Landau theory, based on the coexistence of antiferromagnetism and superconductivity. We study vortex structure produced for a magnetic field close to . We make a new prediction that may serve to test the theory experimentally.