Tunable colors and conductivity by electroless growth of Cu/Cu2O particles on sol-gel modified cellulose

Nano Research - Development of colored surfaces by formation of nano-structured aggregates is a widely used strategy in nature to color lightweight structures (e.g. butterflies) without the use of...     

Ultra-wideband bandpass filter with hybrid microstrip/CPW structure

A novel ultra-wideband (UWB) bandpass filter (BPF) is presented using the hybrid microstrip and coplanar waveguide (CPW) structure. A CPW nonuniform resonator or multiple-mode resonator (MMR) is constructed to produce its first three resonant modes occurring around the lower end, center, and higher end of the UWB band. Then, a microstrip/CPW surface-to-surface coupled line is formed and modeled to allocate the enhanced coupling peak around the center of this UWB band, i.e., 6.85GHz. As such, a five-pole UWB BPF is built up and realized with the passband covering the entire UWB band (3.1-10.6GHz). A predicted frequency response is finally verified by the experiment. In addition, the designed UWB filter, with a single resonator, only occupies one full-wavelength in length or 16.9mm.     

Triple tangent flank milling of ruled surfaces

This paper presents a positioning strategy for flank milling ruled surfaces. It is a modification of a positioning method developed by Bedi et al. [Comput Aided Des 35 (2003) 293]. A cylindrical cutting tool is initially positioned tangential to the two boundary curves on a ruled surface. Optimization is used to move these tangential points to different curves on the ruled surface to reduce the error. A second optimization step is used to additionally make the tool tangent to a rule line, further reducing the error and resulting in a tool position, where the tool is positioned tangential to two guiding rails and one rule line. The resulting surface has 88% less under cutting than the method of Bedi et al.     

Global modeling of hydrogen using GFDL-AM4.1: Sensitivity of soil removal and radiative forcing

Hydrogen (H₂) has been proposed as an alternative energy carrier to reduce the carbon footprint and associated radiative forcing of the current energy system. Here, we describe the representation of H₂ in the GFDL-AM4.1 model including updated emission inventories and improved representation of H₂ soil removal, the dominant sink of H₂. The model best captures the overall distribution of surface H₂, including regional contrasts between climate zones, when v_d(H₂) is modulated by soil moisture, temperature, and soil carbon content. We estimate that the soil removal of H₂ increases with warming (2–4% per K), with large uncertainties stemming from different regional response of soil moisture and soil carbon. We estimate that H₂ causes an indirect radiative forcing of 0.84 mW m^?2/(Tg(H₂)yr^?1) or 0.13 mW m^?2 ppbv^?1, primarily due to increasing CH₄ lifetime and stratospheric water vapor production.     

Catalytic performance of methacrylate‐based poly‐4‐(dialkylamino)‐pyridines: activity prediction via NMR shifts

The synthesis of the 4‐(dialkylamino)pyridine derivative 3‐(4‐(pyridin‐4‐yl)piperazin‐1‐yl)propyl methacrylate and its copolymerization with n‐butyl methacrylate are presented. The catalytic activity was evaluated in the acylation of tert‐butanol with acetic anhydride yielding tert‐butyl acetate. It is observed that the activity of polymer‐attached 4‐(dimethylamino)pyridine analogues correlates remarkably well with the chemical shift of the β‐pyridyl protons. Differences in catalytic efficiency result from distinct electronic densities of the pyridine ring, while embedding the catalytically active moiety into a polymeric structure has nearly no deleterious effect on the performance. © 2015 Society of Chemical Industry     

Reduction of the elongation at break of thermoplastic polyolefins through melt blending with polylactide and the influence of the amount of compatibilizers and the viscosity ratios of the blend components on phase morphology and mechanics

The objective of this work is the synthesis of a polypropylene/ethylene‐propylene‐rubber (TPO)/polylactide (PLA)/compatibilizer (PVM) blend to reduce the elongation at break of TPO by blending TPO with brittle PLA. Three TPO types with different viscosities were melt blended with PLA and an ethylene/n‐butylacrylate/glycidyl methacrylate terpolymer (PVM) as reactive compatibilizer. All blends had a constant PLA amount of 30 wt%. Two parameters were varied in the experiments, viscosity of the TPO types, and amount of PVM used in the blends. Both parameters played important roles in reducing the nominal elongation at break compared to pure TPO foils and influencing the phase morphology of extruded blend foils. The nominal elongation at break could be reduced by 100‐150% through blending TPO with PLA and PVM. Characterization regarding the blend morphology, especially the size and shape of the dispersed PLA phase in the TPO matrix was done by Environmental Scanning Electron Microscopy (ESEM) images. Investigations of the morphology showed that size and shape of dispersed PLA phases are dependent on the viscosity ratios of the blend components and on the amount of compatibilizer in the blend. AFM images of the polymer blends reveal soft rubbery layers around the dispersed PLA phases. POLYM. ENG. SCI., 56:905–913, 2016. © 2016 Society of Plastics Engineers     

Impact of the coating process on the molecular structure of starch‐based barrier coatings

Molecular analysis of starch structure can be used to explain and predict changes in physical properties, such as water vapor and oxygen barrier properties in packaging materials. Solution casting is a widely used technique to create films from starch formulations. This study compared the molecular properties of these standard films with those of experimental coatings applied to paper in laboratory‐scale and pilot‐scale trials, with all three techniques using the same starch formulation. The results revealed large differences in molecular structure, i.e., cross‐linking and hydrolysis, between films and coatings. The main differences were due to the shorter drying time allowed to laboratory‐scale coatings and the accelerated drying process in pilot trials owing to the high energy output of infrared dryers. Furthermore, surface morphology was highly affected by the coating technique used, with a rougher surface and many pinholes occurring in pilot‐scale coatings, giving lower water vapor permeability than laboratory‐scale coatings. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41190.