Multilayer power printed structures suitable for controlling EMI noises generated in power converters

Electromagnetic interference (EMI) noises generated in power converters are diffused on the surface of conductors. This means influences occur from radiated EMI noises emitted from power transmission lines as well as conducted EMI noises transmitted from them. EMI noises diffusing on the surface of conductors are generally difficult to control using conventional concentrated constant theory. Thus, a new approach based on distributed constant circuit theory is needed in order to control EMI noises. A power converter structure to control EMI noises using multilayer power printed circuit technology is studied in this paper. A structure which can control EMI noises should simultaneously satisfy two conditions, i.e., one to shut down and one to attenuate EMI noises. The structure satisfying these conditions is studied through simulations using the Transmission-Line Modeling Method. The simulations show that the diffusion of EMI noises is controlled by dividing the flow of currents produced by EMI noises into the horizontal and perpendicular directions. That is, the horizontal current flow is controlled inside using the differences in the resistance produced from differences between inner and outer diameter of power transmission lines and the perpendicular current flow can be controlled by properly designing the thickness of the dielectric layer sandwiched between P-and N-power transmission lines with the symmetrical structure. Moreover, it is confirmed by simulations and experiments that the attenuation of EMI noises is affected by the width of the power transmission lines. It is expected that the results obtained in this paper can provide important rules when designing power converters with EMI noise control functions which use the multilayer power printed circuit technology.     

Driving voltage reduction in a two-phase CCD by suppression ofpotential pockets in inter-electrode gaps

This study reports an optimum design for a two-phase charge-coupled device (CCD) and limitations on its driving voltage reduction. The two-phase CCD to be used as a horizontal-CCD (H-CCD) in a CCD image sensor requires low-voltage and high-speed operation. Reducing the driving voltage, however, may induce potential pockets in the channel under the inter-electrode gaps which results in a fatal decrease in charge-transfer efficiency. In this case it is necessary to optimize the CCD design to be free of pocket generation. For this requirement, we conducted two-dimensional (2-D) device simulations for the two-phase CCD, whose potential barriers are formed by boron ion-implantation. Our simulations indicated that the edge position of the potential barrier region and the dose of boron-ion implantation would be important parameters for controlling the size of potential pockets. At an optimum edge position and a boron dose, the minimum driving voltage appears to be reducible to 1.1 V. Characteristics of potential pockets and methods of their suppression are also discussed     

Synthesis, structure and antitumor activity of a new water-soluble platinum complex, (1R,2R-cyclohexanediamine-N,N'')[2-hydroxy-4-oxo-2-pentenoato(2-)-O2] platinum(II)

Patients with thalassemia major require multiple blood transfusions leading to hemochromatosis. These patients often have pubertal delay and growth failure, the etiology of which has not been fully elucidated. We performed an extensive endocrine evaluation which included measurements of spontaneous and stimulated levels of gonadotropins, GH, thyroid hormone, and adrenal hormones in 17 patients between the ages of 12 and 18 yr with hemochromatosis receiving desferoxamine therapy. All of the 17 patients had at least one endocrine abnormality, and 12 had more than one abnormality. Abnormalities of the hypothalamic-pituitary-gonadal axis were the most common. Six patients had clinical evidence of delayed puberty with spontaneous and stimulated gonadotropin and sex steroid levels appropriate for their delayed pubertal stage. All 14 children in puberty LH pulsatility index below the mean for pubertal stage compared to normal children. Six of the 14 had LH pulsatility index more than 2 SD below the mean for pubertal stage. This may be an indicator of abnormal pituitary function. Six patients failed either the provocative GH tests (peak GH < 7 micrograms/L) or had a mean spontaneous GH less than 1 microgram/L. The 4 patients who failed provocative tests had growth velocities more than 2 SD below the mean for bone age. Three patients had evidence of primary hypothyroidism. We conclude that all patients with hemochromatosis need periodic careful endocrine evaluations because the incidence of endocrine dysfunction is substantial and they may benefit from hormonal therapy.     

Rolling contact fatigue behavior of sintered and hardened steels

Powder-metal-processed bearings and gears are finding increasing application because of their economical and technical advantages. The residual pores from the sintering operatives act as lubricant pockets and dampen sound and vibration. However, porosity also decreases the mechanical strength and reduces the life of components fabricated by powder processing relative to similar wrought components. The rolling contact fatigue behavior of sintered and heat treated steel rollers was investigated using a fatigue test machine designed and fabricated for that purpose. The powder-metal-processed and the wrought steel rollers that were tested had similar composition and hardness and were mated against wrought steel rollers of high hardness. The contact stress versus number of cycles to failure data showed that the wrought steel had a very high endurance limit under rolling contact fatigue compared to the sintered steels investigated. Rolling contact fatigue behavior was found to depend on the porosity present in the material. Large surface peeling failures and pitting type fatigue failures were observed in the sintered and hardened steels, while only pitting type failures were observed in the wrought steels     

New low-noise output amplifier for high-definition CCD image sensor

A new low-noise charge-coupled-device (CCD) output amplifier, the RJG detector, has been developed. The RJG detector incorporates a JFET which has an electrically floating ring-junction gate (RJG). The operating principle of the amplifier is that signal charges, transferred from the CCD into the RJG, directly modulate the drain current in the detection JFET. The performance of the detector was evaluated by operating test devices under a 37-MHz clock frequency, which is the same frequency as that for the horizontal CCD operation in the recently developed 2-million-pixel high-definition CCD image sensor. It was found that 1/f noise was reduced by introducing the JFET and that reset noise was completely eliminated by achieving complete charge transfer through the reset operation. As a result, input referred noise equivalent electrons within the 18.5-MHz baseband were reduced to 17 (electrons)     

Low-cycle fatigue behavior of Sn-Ag, Sn-Ag-Cu, and Sn-Ag-Cu-Bi lead-free solders

Low-cycle fatigue (LCF) tests on as-cast Sn-3.5Ag, Sn-3Ag-0.5Cu, Sn-3Ag-0.5Cu-1Bi, and Sn-3Ag-0.5Cu-3Bi solders was carried out using a noncontact strain-controlled system at 20°C with a constant frequency of 0.1 Hz. The addition of Cu does not significantly affect the fatigue life of eutectic Sn-Ag solder. However, the fatigue life was significantly reduced with the addition of Bi. The LCF behavior of all solders followed the Coffin-Manson relationship. The fatigue life of the present solders is dominated by the fracture ductility and can be described by the ductility-modified Coffin-Manson’s relationship. Steps at the boundaries of dendrite phases were the initiation sites for microcracks for Sn-3.5Ag, Sn-3Ag-0.5Cu, and Sn-3Ag-0.5Cu-1Bi solders, while for Sn-3Ag-0.5Cu-3Bi solder, cracks initiated along both the dendrite boundaries and subgrain boundaries in the dendrite phases. The linking of these cracks and the propagation of cracks inside the specimen occurred both transgranularly through eutectic phases and intergranularly along dendrite boundaries or subgrain boundaries.     

Suboptimal exact model matching for multivariable systems withmeasurement noise

This paper describes a method for the design of discrete-time model matching control systems for a multivariable plant with measurement noise. This method uses a new parametrization for model matching controllers. Simulation results are presented which confirm the validity of the design method     

Further investigation on the thermal decomposition of aluminium dialkylamides

Both dimethylamino- (I) and diethylamino-alane dimers (II), [(R₂N)₂AlH]₂ (I, R=Me; II, R=Et) decompose above 800° C under a few hundred Pa of hydrogen to dark greyish, hard (Vickers hardness larger than 2000), oxidation-resistive and oxidation-protective deposits which are tentatively identified as Al₅C₃N. The deposits are stable to moisture and diluted hydrochloric acid in contrast to those obtained below 800° C, but they easily dissolve in sodium hydroxide solution at room temperature evolving a gas. The deposits on a stainless steel substrate adhere strongly to the substrate and remain so on rapid heating and cooling. The electrical resistivity of the deposits is in the range 10² to 10⁴ cm.     

On the number of overload-induced delay cycles as a function of thickness

In this paper, a brief review of the experimental facts associated with the crack growth delay period following a tensile overload is given. In the retardation process, crack closure is considered to play a dominant role. A scenario for the two crack opening processes which develop as a fatigue crack penetrates the overload plastic zone is presented. This scenario deals with the effect of specimen thickness on the crack opening processes. Consideration is given to the delay distance and to the minimum crack growth rate. A method of analysis for the determination of the number of delay cycles following an overload is then developed. Finally the method of analysis is used to compare with recent experimental results.