Performance of surface ionic conduction single chamber fuel cell prepared by the sol gel method

The performance of surface ionic conduction single chamber fuel cell (SIC‐SCFC) prepared by the sol gel method was studied on electric characteristics due to the differences of the operating temperature and humidity, the electrode distance and electrolyte film depth, and multiple cells with the series and parallel connections. The SIC–SCFC was arranged the both anode of Pt and cathode of Au on the boehmite electrolyte. The open circuit voltage (OCV) of single cell achieved a maximum of 530mV in the dry gas mixtures of O₂/H₂=50% in room temperature operation, and but it became decrease as over 60%. The OCV was maintained the constant value between operating temperatures of 30°C to 80°C, and but it was decreased sharply at over 90°C because a humidity on the cell became lower as increasing operating temperature. Then, the cell property was improved to 120°C by adding to the humidity of 70% using a humidifier. The electrode distance and the electrolyte film depth of SIC‐SCFC found to be contributed to the reductions of the cell resistance and the surface roughness on the electrode, respectively. Moreover, the power property of SIC‐SCFC was significantly improved by cell stacks comprised of the series or parallel connection of a cell.     

Repulsive Flux Pinning Force in NbTi/Nb Superconductor/Superconductor Multilayers

Flux pinning characteristics have been investigated for the Nb _x Ti_100-x /Nb(x = 65, 50 and 28) and Nb ₂₈ Ti ₇₂/Nb ₆₅ Ti ₃₅ superconductor(S)/superconductor(S^′) multilayers. The maximum of the pinning force F _{p⊥ max} perpendicular to the layer plane as a function of the structure modulation length λ has a peak in the quasi-two-dimensional region (λ～20 nm). The maximum. values of the F _{p⊥ max} versus λ curve are proportional to the difference of the GL coherence length (ξ _GL ) between the superconductive sublayers S and S^′. The results suggest that the large F _{p⊥ max} in the S/S^′ multilayer is caused by the repulsive pinning force due to Nb layers with larger ξ _GL .     

Coating of hydroxyapatite on metal plates using thermal dissociation of calcium-EDTA chelate in phosphate solutions under hydrothermal conditions

Coating of hydroxyapatite on various metal plates was carried out by a homogeneous precipitation technique using hydrothermal reactions in Ca(edta)^2-–NaH₂PO₄ at 140–200°C and pH 3.4–10.0. Hydroxyapatite films were formed on the surface of the iron plates in solutions at an initial pH above 4.7, whereas aggregates consisting of needle-like hydroxyapatite crystal radiating from a point in the form of flower deposited as islands on the surface of aluminum, copper and titanium plates. The upper part of the film formed on the surface of the iron plates consisted of needle-like hydroxyapatite particles whereas the bottom of the film consisted of spherical hydroxyapatite particles. The length of the needle-like hydroxyapatite particles increased with decreasing concentration of Ca(edta)^2-.     

Effect of 8 MeV electron irradiation on electrical properties of CuInSe2 thin films

Radiation damages due to 8 MeV electron irradiation in electrical properties of CuInSe₂ thin films have been investigated. The n-type CuInSe₂ films in which the carrier concentration was about 3×10¹⁶ cm⁻³, were epitaxially grown on a GaAs(0 0 1) substrate by RF diode sputtering. No significant change in the electrical properties was observed under the electron fluence <3×10¹⁶ e cm⁻². As the electron fluence exceeded 10¹⁷ e cm⁻², both the carrier concentration and Hall mobility slightly decreased. The carrier removal rate was estimated to be about 0.8 cm⁻¹, which is slightly lower than that of III–V compound materials.     

Current collecting efficiency of micro tubular SOFCs

In this study, current collecting efficiency of the micro tubular solid oxide fuel cell (SOFC) was estimated to determine optimum size of the micro tubular SOFC. Two models for collecting current from single terminal (ST) and double terminal (DT) of anode tube were proposed and used to calculate the current collecting efficiency as functions of anode thickness, tube length and operating temperature. It was shown that design of the cell geometry and current correcting method are significantly important to achieve high performance micro tubular SOFC stacks. The efficiency loss estimated from the DT model was about 2–4-fold lower than those of obtained from the ST model. The DT model was shown to be more effective for higher operating temperature and the tube length.     

Thermal strain of high strength polyethylene fiber in low temperature

High strength polyethylene fiber (Toyobo, Dyneema® fiber: hereinafter abbreviated to DF) has a negative thermal expansion coefficient. Relation between fiber structure and thermal strain of DF used as reinforcement of DF reinforced plastic (DFRP) for cryogenic use was investigated. The crystallinities and orientation angles of several kinds of polyethylene fibers having different modulus from 15 to 134Gpa (herein after abbreviated to DFs) were measured by NMR and X‐ray. We obtained the parameters of the mechanical series‐parallel model composed of crystal and amorphous by crystallinity and modulus. Thermal expansion coefficients of DFs were estimated by mechanical series‐parallel model. All DFs having different modulus showed negative thermal expansion coefficients in the temperature range from 180 to 300K, and absolute values of those markedly increased by increasing tensile modulus of DF. The estimated thermal expansion coefficients showed negative values, and thermal strains showed a similar curve to observed ones mostly. Average thermal expansion coefficients in the temperature range from 180 to 300K estimated by mechanical model agreed with the observed ones. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2918–2925, 2004     

Self-aligned fabrication of single crystal diamond gated field emitter array

This paper describes a self-aligned fabrication process for diamond gated field emitter array (FEA). Utilizing the non-conformal coverage sputtering conditions of silicon oxide, an interesting “sphere on cone” structure is formed on diamond nano tip array, which is the key point of gate hole opening process. This structure causes shadowing at certain regions of side-wall during Ti / Au gate metal deposition. Removal of “sphere” by wet etching leads to the successful fabrication of a single crystalline diamond gated FEA. Scanning electron microscope observations reveal the fabrication of a uniform emitter array with tip radius of curvature (20 nm) and gate hole (1.4 μm). We also confirmed that no noticeable physical damage exists on tip. In field emission characteristics of the fabricated single crystal diamond gated FEA, gate voltage control of field emission current is realized.     

Effect of Microstructural Control on Thermoelectric Properties of Hot-Pressed Aluminum-Doped Zinc Oxide

The thermal conductivity of polycrystalline Al-doped ZnO was controlled through the fabrication of nanostructured polycrystalline materials, by hot-pressing nanosized Zn_{1– x} Al _x O ( x = 0.01, 0.02) particles, which were synthesized by a coprecipitation and spray-drying method. This process resulted in an improved thermoelectric power factor because of the nanosized Zn_0.99Al_0.01O particles of the polycrystalline products. The thermal conductivity also was decreased as a result of the formation of nanocrystalline Zn_0.99Al_0.01O.     

Gaze direction based vehicle teleoperation method with omnidirectional image stabilization and automatic body rotation control

In robot teleoperation, a robot works as a physical agent at a remote site for a robot operator. There are mainly two tasks in robot teleoperation using camera images: environment recognition using visual information and robot control according to the recognition. In this paper, we propose a gaze direction based vehicle teleoperation method with an omnidirectional image stabilization and an automatic body rotation control. In the proposed method, we manage above two tasks in the same manner that are usually treated separately. This method is an intuitive vehicle teleoperation method where an operator do not need to have concern about vehicle body orientations and can absorb differences of vehicle driving mechanisms. That is, this method frees an operator from being bothered from controlling a vehicle and the operator can concentrate on where he/she intends to go. This method mainly consists of two technologies: an omnidirectional image stabilization technology and automatic body rotation control. The conducted experiments show effectiveness of the proposed method.