Ultraviolet chambers based on integrating spheres for use in artificial weathering

Laboratory ultraviolet (UV) chambers are widely used to obtain weathering data for a wide range of commercial polymer products including coatings, textiles, elastomers, plastics, and polymeric composites. Although numerous improvements have been made in the design of UV chambers over the last 80 years, the reproducibility of the exposure results from these chambers has remained elusive. This lack of reproducibility is attributed to systematic errors in their design, operation, and control which prevent direct comparisons of the performance of materials exposed in the same environment, comparisons of the performance of the same material exposed in different laboratories, and the comparison of field and laboratory results. This paper describes an innovative UV chamber design based on integrating sphere technology that greatly reduces the magnitude of these errors, as well as provides additional experimental capabilities. Presented at the 79th Annual Meeting of the Federation of Societies for Coatings Technology, on November 4–7, 2001, in Atlanta, GA. Building Materials Division. Gaithersburg, MD. Freeport, TX.     

Economic analysis of tirilazad mesylate for aneurysmal subarachnoid hemorrhage. Economic evaluation of a phase III clinical trial in Europe and Australia

This study used data from a multinational phase III randomized, double-blind, vehicle-controlled trial to evaluate the cost-effectiveness of tirilazad mesylate (Freedox) in the treatment of aneurysmal subarachnoid hemorrhage. In men, therapy with 6 mg/kg per day of tirilazad mesylate was associated with significantly increased survival, increased cost of care, and ratios of cost per death averted that compare favorably with the ratios of other life and death interventions. In women, it appeared to have no effects on costs or survival. Further clinical studies may provide additional information about the cost-effectiveness of this intervention.     

A Monte Carlo investigation of the dual photopeak window scattercorrection method [SPECT]

Results from a Monte Carlo investigation of the dual photopeak window (DPW) scatter correction method are presented for point and extended sources of Tc-99m in both homogeneous and nonhomogeneous attenuating media. The DPW method uses the ratio of counts in two nonoverlapping energy windows within the photopeak region as input to a regression relation. A pixel-by-pixel estimate of the scatter in the summed windows is obtained and subtracted to yield an estimate of the primary. An approximate tenfold decrease in the scatter fraction and an excellent agreement with the shape of the true scatter distribution were observed     

Reduced skin tumor development in cyclin D1-deficient mice highlights the oncogenic ras pathway in vivo

Cyclin D1 is part of a cell cycle control node consistently deregulated in most human cancers. However, studies with cyclin D1-null mice indicate that it is dispensable for normal mouse development as well as cell growth in culture. Here, we provide evidence that ras-mediated tumorigenesis depends on signaling pathways that act preferentially through cyclin D1. Cyclin D1 expression and the activity of its associated kinase are up-regulated in keratinocytes in response to oncogenic ras. Furthermore, cyclin D1 deficiency results in up to an 80% decrease in the development of squamous tumors generated through either grafting of retroviral ras-transduced keratinocytes, phorbol ester treatment of ras transgenic mice, or two-stage carcinogenesis.     

Noniterative compensation for the distance-dependent detector response and photon attenuation in SPECT imaging

A filtering approach is described, which accurately compensates for the 2D distance-dependent detector response, as well as for photon attenuation in a uniform attenuating medium. The filtering method is based on the frequency distance principle (FDP) which states that points in the object at a specific source-to-detector distance provide the most significant contribution to specified frequency regions in the discrete Fourier transform (DFT) of the sinogram. By modeling the detector point spread function as a 2D Gaussian function whose width is dependent on the source-to-detector distance, a spatially variant inverse filter can be computed and applied to the 3D DFT of the set of all sinogram slices. To minimize noise amplification the inverse filter is rolled off at high frequencies by using a previously published Wiener filter strategy. Attenuation compensation is performed with Bellini's method. It was observed that the tomographic point response, after distance-dependent filtering with the FDP, was approximately isotropic and varied substantially less with position than that obtained with other correction methods. Furthermore, it was shown that processing with this filtering technique provides reconstructions with minimal degradation in image fidelity.     

Optimization of a proton exchange membrane fuel cell membrane electrode assembly

A computational framework for fuel cell analysis and optimization is presented as an innovative alternative to the time consuming trial-and-error process currently used for fuel cell design. The framework is based on a two-dimensional through-the-channel isothermal, isobaric and single phase membrane electrode assembly (MEA) model. The model input parameters are the manufacturing parameters used to build the MEA: platinum loading, platinum to carbon ratio, electrolyte content and gas diffusion layer porosity. The governing equations of the fuel cell model are solved using Netwon’s algorithm and an adaptive finite element method in order to achieve near quadratic convergence and a mesh independent solution respectively. The analysis module is used to solve the optimization problem of finding the optimal MEA composition for maximizing performance. To solve the optimization problem a gradient-based optimization algorithm is used in conjunction with analytical sensitivities. By using a gradient-based method and analytical sensitivities, the framework presented is capable of solving a complete MEA optimization problem with state-of-the-art electrode models in approximately 30 min, making it a viable alternative for solving large-scale fuel cell problems.     

Student perceptions of model-based estimating

The use of building information modeling (BIM) is well established in architecture, engineering and construction. However, previous studies note a lack of BIM expertise in academia, leading to slow adoption and limited knowledge on which to base BIM-related content. To improve course development, it is important to understand students’ perceptions of BIM-related subject matter. This study exposed estimating students (n = 214) to a model-based quantity takeoff (QTO) tutorial using Revit. Students’ perceptions of a Revit-based BIM’s usefulness for easily providing reliable and accurate material quantities were measured using a pre-test, tutorial and post-test design. Results revealed significant differences in students’ mean levels of agreement that an accurate QTO is completed for an estimator with the click of a button when a design team generated BIM model is available. Results also revealed significant differences in students’ level of agreement that a Revit-based BIM makes performing QTO by hand obsolete. This study provides educators’ insight into students’ perceptions of BIM use in QTO. Understanding student perceptions is paramount for construction management educators when designing a course and attempting to convey the value of foundational estimating skills while acknowledging the existence of more technologically advance estimating methods. Limitations and opportunities for further research are discussed.     

A Plan for the Development of Fusion Energy

This is the final report of a panel set up by the U.S. Department of Energy (DOE) Fusion Energy Sciences Advisory Committee (FESAC) in response to a charge letter dated September 10, 2002 from Dr. Ray Orbach, Director of the DOE's Office of Science. In that letter, Dr. Orbach asked FESAC to develop a plan with the end goal of the start of operation of a demonstration power plant in approximately 35 years. This report, submitted March 5, 2003, presents such a plan, leading to commercial application of fusion energy by mid-century. The plan is derived from the necessary features of a demonstration fusion power plant and from the time scale defined by President Bush. It identifies critical milestones, key decision points, needed major facilities and required budgets. The report also responds to a request from DOE to FESAC to describe what new or upgraded fusion facilities will best serve our purposes over a time frame of the next twenty years.