Research and development of liquid hydrogen (LH2) temperature monitoring system for marine applications

Monitoring the temperature in liquid hydrogen (LH₂) storage tanks on ships is important for the safety of maritime navigation. In addition, accurate temperature measurement is also required for commercial transactions. Temperature and pressure define the density of liquid hydrogen, which is directly linked to trading interests. In this study, we developed and tested a liquid hydrogen temperature monitoring system that uses platinum resistance sensors with a nominal electrical resistance of approximately 1000 Ω at room temperature, PT-1000, for marine applications. The temperature measurements were carried out using a newly developed temperature monitoring system under different pressure conditions. The measured values are compared with a calibrated reference PT-1000 resistance thermometer. We confirm a measurement accuracy of ±50 mK in a pressure range of 0.1 MPa–0.5 MPa.     

Hot carrier magnetophonon spectroscopy of semiconductors in high magnetic fields up to 40 T

Hot carrier magnetophonon resonances of n-type Si, short channel InP and p-type InSb were investigated in pulsed high magnetic fields up to 40 T. Using a recently developed high resolution technique in pulsed high fields, many new features of the hot carrier-phonon interactions in high magnetic fields were found.     

Fate of the chlorine and fluorine in a sub-bituminous coal during pyrolysis and gasification

The fate of the chlorine and fluorine present in a sub-bituminous coal from Indonesia during pyrolysis and gasification has been studied with fixed and entrained bed reactors. The rate profile for HCl evolved in the temperature programmed pyrolysis exhibits the main and shoulder peaks at 480 and 600 °C, respectively. Model experiments and subsequent Cl 2p XPS measurements show that HCl reacts with metal impurities and carbon active sites at 500 °C to be retained as inorganic and organic chlorine forms, from which HCl evolves again at elevated temperatures. It is suggested that the HCl observed in the coal pyrolysis may originate from the above-mentioned chlorine functionalities formed by secondary reactions involving the nascent char. In the CO₂ gasification of the 900 °C char at 1000 °C and 2.5 MPa, any measurable amounts of HCl and HF could not be detected even at a high conversion of 75 wt% (daf), suggesting the accumulation of these halogens in the residual char. When the coal is injected into an O₂-blown, entrained bed gasifier at 1200-1400 °C under 2.6 MPa, the partial oxidation proceeds to a larger extent at a higher O₂/coal ratio, whereas the chlorine and fluorine are enriched in the remaining char, and the extent of the enrichment at the latter stage of gasification is larger with the fluorine. The XPS measurements of the chars reveal the presence of the broad F 1 s peak, which can cover a wide range of binding energies attributable to inorganic and organic fluorine. The halogen enrichment during gasification is discussed in terms of secondary reactions of HCl and HF with char.     

Studies on miscibility in homopolymer/ random copolymer blends by equation of state theory

The miscibility of poly(methyl methacrylate) (PMMA) and styrene-acrylonitrile random copolymers (SAN) blends was investigated on the basis of the Flory—Orwoll—Vrij equation of state theory. To obtain the equation of state parameters (P*, V*_sp, T*: characteristic parameters), the pressure—volume—temperature (PVT) behaviour was measured for PMMA and a series of SANs with various acrylonitrile contents. The exchange energy parameter X_ij was also calculated by fitting the theory to some phase diagrams of PMMA/SAN blends. The Flory—Huggins interaction parameter χ was separated into two contributions based on the equation of state theory for mixtures: the exchange energy term χ_inter and the free volume term χ_free. Both the temperature and copolymer composition dependences of χ_inter and χ_free were estimated by calculations using the equation of state parameters. There exists a region in which χ_inter is negative, leading to a miscibility window in PMMA/SAN blends. However, the immiscibility at high temperatures in the blends cannot be explained only by χ_inter; it is caused by the free volume contribution, χ_free. The miscibility window behaviour in PMMA/SAN blends may be explained within the framework of the equation of state theory.     

Effect of polymer density on polyethylene hollow fiber membrane formation via thermally induced phase separation

Microporous high‐density polyethylene (HDPE) and low‐density polyethylene (LDPE) hollow fiber membranes were prepared from polyethylene–diisodecyl phthalate solution via thermally induced phase separation. Effect of the polyethylene density on the membrane structure and performance was investigated. The HDPE membrane showed about five times higher water permeability than the LDPE membrane because it had the larger pore and the higher porosity at the outer membrane surface. The formation of the larger pore was owing to both the initial larger structure formed by spinodal decomposition and the suppression of the diluent evaporation from the outer membrane surface due to the higher solution viscosity. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 471–474, 2004     

Preparation of Aluminum Nitride Powder from Aluminum Polynuclear Complexes

AIN powder was synthesized from aluminum polynuclear complexes. Basic aluminum chloride and basic aluminum lactate were used as the aluminum polynuclear complexes. These starting materials and glucose were dissolved in water and mixed homogeneously. AIN powder was obtained by calcining after drying and precalcining at 800°C under nitrogen gas flow. Then excess carbon was removed by firing in air. Nitridation in the system was investigated and compared with that in the alumina–carbon black system. It was found that in our reaction system nitridation began and proceeded at lower calcination temperatures above 1200°C than in the alumina–carbon black system. Using aluminum polynuclear complexes, AIN was synthesized through the nitridation of γ-alumina and produced in a very fine and sharp particle size distribution.     

Studies on the biaxial stretching of polypropylene film. XI. Type II orientation during [2-2FI]-type stretching and its change by subsequent thermal contraction

In order to study the deformation mechanism of type II stretching, the change in orientation during the restretching and subsequent thermal contraction was investigated by x-ray diffraction method. When a uniaxially oriented film is restretched, the lamellae which are stacked in the stretching direction by the stretching rotate as a whole toward the restretching axis. They rotate backward nearly reversibly during the thermal contraction, unless the restretching exceeds a balancing state, where the orientation in the film plane are equal in all directions. However, when the restretching degree is so high and the film orientation exceeds the balancing state, the lamellar rotation is accompanied by a complex phenomenon. It is considered from the wide-angle and small-angle x-ray diffraction patterns that the lamellar surface becomes indented because of slippage between microfibrils composing the lamellae, and the microfibrils themselves bend at the boundary between the amorphous and crystalline regions within which the tilting of c-axis also occurs. Upon contracting of the film; these changes recover, but even in the last stage of contraction the orientation approaches the symmetrical biaxial orientation but not the uniaxial orientation from which the biaxial orientation is started. These orientation and disorientation behaviors are not affected basically by a slight change in the restretching temperature and the degree of stretching.