Dysprosium doped copper oxide (Cu1-xDyxO) nanoparticles enabled bifunctional electrode for overall water splitting

The production of hydrogen, a favourable alternative to an unsustainable fossil fuel remains as a significant hurdle with the pertaining challenge in the design of proficient, highly productive and sustainable electrocatalyst for both oxygen evolution reaction (OER) and hydrogen evolution reaction (HER). Herein, the dysprosium (Dy) doped copper oxide (Cu_1-xDy_xO) nanoparticles were synthesized via solution combustion technique and utilized as a non-noble metal based bi-functional electrocatalyst for overall water splitting. Due to the improved surface to volume ratio and conductivity, the optimized Cu_1-xDy_xO (x = 0.01, 0.02) electrocatalysts exhibited impressive HER and OER performance respectively in 1 M KOH delivering a current density of 10 mAcm^?2 at a potential of ?0.18 V vs RHE for HER and 1.53 V vs RHE for OER. Moreover, the Dy doped CuO electrocatalyst used as a bi-functional catalyst for overall water splitting achieved a potential of 1.56 V at a current density 10 mAcm^?2 and relatively high current density of 66 mAcm^?2 at a peak potential of 2 V. A long term stability of 24 h was achieved for a cell voltage of 2.2 V at a constant current density of 30 mAcm^?2 with only 10% of the initial current loss. This showcases the accumulative opportunity of dysprosium as a dopant in CuO nanoparticles for fabricating a highly effective and low-cost bi-functional electrocatalyst for overall water splitting.     

EC Analysis of Multi-Antenna System over 5G and Beyond Networks and its Application to IRS-Assisted Wireless Systems

Wireless Personal Communications - Recently, the theory of effective rate has attracted much attention, since it can take the delay aspect into account when performing channel capacity analysis. In...     

Domain Adaptation for POS Tagging with Contrastive Monotonic Chunk-wise Attention

Neural Processing Letters - Part of Speech (POS) tagging is a sequential labelling task and one of the core applications of Natural Language Processing. It has been a challenging problem for the...     

Impact of Mole Fractions due to Work Function Variability (WFV) of Metal Gate on Electrical Parameters in Strained SOI-FinFET

In the recent sub-20 nm technology node, the process variability issues have become a major problem for scaling of MOS devices. We present a design for a strained Si/SiGe FinFET on an insulator using a 3D TCAD simulator. The impact of metal gate work function variability (WFV) on electrical parameters is studied. Such impact of WFV for different mole fractions (x) of the SiGe layer in a strained SOI-FinFET with varying grain size is presented. The results show that as the mole fraction is increased, the variability in threshold voltage (σVT) and off current (σIoff) is decreased; while, the variability of on-current (σIon) is increased. A notable observation is the distribution of electrical parameters approaches a normal distribution for smaller grain sizes.     

Cut off frequency and transit time analysis of lightly doped drain (LDD) MOSFETs

Analytical model for the transconductance, cut off frequency, transit time and fringing capacitance of LDD MOSFETs is presented with a simple approach. The analysis is carried out considering the LDD device as a conventional MOSFET with a series resistance [Z.-H. Liu et al., Threshold voltage model for submicrometer MOSFETs. IEEE Trans Electron Devices 1993; ED-40: 86–94] and a simple closed form expressions for cut off frequency and transit time is obtained. The total gate capacitance, i.e. the geometric and fringing capacitance, is calculated for both LDD and non-LDD devices and lower fringing capacitance is reported in LDD devices. Lower cut-off frequencies and higher transit time are reported in LDD devices for the same channel length.     

Microstructural Investigation on Failure of Internal Drive Shaft

17-4 PH stainless steel is used as internal drive shaft material in liquid engine pumps. One of the drive shafts failed during operation. The shaft pieces were in contact for short duration after failure, which has resulted in abrasion of fractured surfaces. Samples from the location of failure were taken, and investigation of the failure was carried out using optical and scanning electron microscopy. The microstructural analysis of the material and fractographic analysis of the fractured surface show that the failure was caused by excessive torsion.     

Electrosynthesis and impedance studies on zinc selenide

Electrochemical impedance measurements have been used to characterize zinc selenide films prepared by electrochemical co-deposition at a platinum rotating disk electrode. Estimations of capacitance and polarization resistance of variously prepared electrodeposits have been carried out to determine charge carrier density and corrosion rates.     

Microstructural developments in Mg-Ti-PSZ systems

The microstructure of titania-added Mg-partially-stabilized zirconia (PSZ) is dramatically influenced by thermal treatments. Effects of various sintering, heat-treatment and thermal shock cycling parameters on the microstructure of the Mg-Ti-PSZ system are described. Conditions favourable for the growth of needle-like Ti-rich reinforcements in highly thermalshock-resistant Mg-Ti-PSZ ceramics are identified. TiO₂ seems to play a catalytic role in the formation of Zr-rich networks during high-temperature (1700°C) sintering of the Mg-Ti-PSZ system, quite similar to those found in Mg-PSZ, heat-treated above 1300 °C.