The electrical and dielectric characterization of the Co/ZnO-Rods/p-Si heterostructure depending on the frequency

Journal of Materials Science: Materials in Electronics - Zinc oxide (ZnO) rods film was fabricated by homemade and simple spray pyrolysis technique on a p-type silicon (Si) substrate, and the film...     

Performance of a Tied-Arch Reinforced Concrete Railway Bridge: Rating, Safety Assessment, and Bond Length Evaluation

This study presents investigations regarding visual inspection, dynamic testing, and finite-element modeling of an approximately 80-year old reinforced concrete tied-arch railway bridge that is still in service in Turkey. Investigations were conducted as part of a systematic periodic inspection along Ankara-Zonguldak railway line. The bridge is subject to heavy freight trains with increasing axle loads. Field tests such as material tests and dynamic tests were used to calibrate the finite-element model of the bridge. Detailed information regarding testing and model updating procedure is given. Based on test results, computer model was refined. The calibrated model of the bridge structure was then used for structural assessment and evaluation. Despite sufficient overall safety, local details were found to be problematic. Due to insufficient bond length in hanger-to-arch connection, a strengthening scheme using steel channel sections was proposed.     

Solid solution limit of Fe2O3 in mullite crystals,produced from kaolin by solid state reactions

Porcelain, wall/floor tiles, and roofing tiles are classified as traditional ceramics and are produced from natural raw materials such as clay, quartz, and feldspar. The raw materials are selected by the oxide content which provides the desired properties of the final product. However, impurities such as Fe₂O₃ and TiO₂ may have a significant influence on both physical/mechanical properties and aesthetic appearance. Fe₂O₃, which is of particular importance, causes black maculation formation in tablewares, in which whiteness is essential. The only way to overcome the black maculation is to corrupt the Fe₂O₃ crystal structure and to employ Fe^2+/3+ cation, making a solid solution with a host crystal (i.e. mullite-3Al₂O₃·2SiO₂). The aim of this study is to identify the solubility limit of Fe₂O₃ in mullite crystals. With the scope of the study, an illite/kaolinite was utilized by adding an increasing amount of Fe₂O₃ (e.g. 1–2–4–6–8–10?wt%) into the recipes fired at 1300?°C for 3?h after homogenization. According to the mullite phase content, it is concluded that ~ 5?wt% of Fe₂O₃ could be dissolved in mullite crystal structure on the basis of the Rietveld refinement of the XRD patterns.     

Comparison of open and closed circuit HPGR application on dry grinding circuit performance

A conventional cement grinding circuit is composed of a two compartment tube mill, a mill filter which collects the fine material inside the mill and a dynamic air separator where final product with required fineness is collected. In general the material fed to the circuit has a top size of 50 mm which is very coarse for the ball mill. For this purpose, later in 1980s, high pressure grinding rolls (HPGR) has found applications as a pregrinder which increased throughput of the grinding circuit at the same fineness.In early applications, HPGR was operated in open circuit. But later as the operating principle of the equipment based on the compression, some portion of the HPGR discharge recycled back to improve efficiency of the mill or operated closed circuit with classifiers. Within this study effect of open and closed circuit HPGR applications on dry grinding circuit performance was examined. For this purpose sampling studies around three different cement grinding circuit were completed. In the first study, a circuit including open circuit HPGR, ball mill and air separator was sampled and chosen as the basic condition. As the final product size distribution is important for grinding circuit, model structure of each equipment was developed. The second and third surveys were carried out around closed circuit HPGR operation with V and VSK separator to develop models for the separators. Finally the separator models were used in basic condition to simulate closed circuit HPGR application.It was understood from the studies that closed circuit HPGR operation improved the overall circuit efficiency at the same final product fineness by reducing the specific energy consumption.     

Determination of Membrane Protein Fouling by UV Spectroscopy and Electrochemical Impedance Spectroscopy

UV spectroscopy and electrochemical impedance spectroscopy were used to investigate the properties and performances of ultrafiltration membranes fabricated with different polymers. Membrane performances were studied by means of permeability and bovine serum albumin filtration. UV spectroscopy results showed that bovine serum albumin rejection was lowest in polyvinylidene fluoride membranes, whereas it was highest in polysulfone membranes. Electrochemical impedance spectroscopy data revealed that after bovine serum albumin filtration, resistance of the membranes was increased though double layer capacitances were decreased. Performance data of UV spectroscopy and electrochemical impedance spectroscopy were in correlation with each other. This study demonstrated that electrochemical impedance spectroscopy can be successfully used in filtration membrane studies.     

Combination of Different Size Distributions for Mineral Particles by Applying Experimentally Determined Apparent Mean Shape Factor

As is well known, the behavior of systems of fine particles is strongly dependent on the size of the individual particles, and the size effects become increasingly important as the particles become progressively smaller. This study covers two different size analysis techniques, sieving and laser diffraction measurement, and constructs whole size distribution for different mill (ball and rod) products of some industrial minerals: barite and quartz minerals. A smooth overlap of corrected laser diffraction size distribution and sieve size distribution was obtained by applying the particle size with the apparent mean shape factor shifting to the right side of the curve for the rod-milled barite and ball- and rod-milled quartz. The apparent mean shape factors determined from the corrected particle size distributions were found to be 1.02 and 1.39 for ball- and rod-milled barite and 1.29 and 1.25 for ball- and rod-milled quartz, respectively. The results indicate that the ball-milled products of barite mineral have more regular (rounder in shape) particles than those of rod-milled barite, but there are not significant differences between the shape factors of ball- and rod-milled products of quartz mineral, i.e., both of them have irregular particles that deviate from spherical shape, as evident from the SEM pictures taken.     

The use of Bacillus subtilis immobilized on Amberlite XAD-4 as a new biosorbent in trace metal determination

The present work proposes the use of Bacillus subtilis immobilized on Amberlite XAD-4 as new biosorbent in trace metal determination. The procedure is based on the biosorption of Cu and Cd ions on a column of Amberlite XAD-4 resin loaded with dried, dead bacterial components prior to their determination by flame AAS. Various parameters such as pH, amount of adsorbent, eluent type and volume, flow rate of solution and matrix interference effect on the retention of the metal ions have been studied. The optimum pH values of quantitative sorption for Cu and Cd were found to be 7.0 and 7.5, respectively. These metal ions can be desorbed with 1M HCl (recovery, 96-100%). The sorption capacity of the resin was 0.0297 and 0.035 mmol g(-1) for Cu(2+) and Cd(2+), respectively. The tolerance limit of some electrolytes were also studied. This procedure was applied to Cu(2+) and Cd(2+) determination in aqueous solutions, including river and well water systems. In order to evaluate the accuracy of the proposed procedure, the certified reference materials, NRCC-SLRS-4 Riverine water and LGC7162 Strawberry leaves were analyzed.     

New monomers and polymers derived from α‐hydroxymethyl methyl vinyl ketone

2‐Hydroxymethyl‐but‐1‐ene‐3‐one [α‐hydroxymethyl methyl vinyl ketone (HMVK)] was synthesized from methyl vinyl ketone using paraformaldehyde and a tertiary amine catalyst. Free‐radical polymerization of this monomer created transparent, tough polymers that were insoluble in organic solvents. HMVK was converted to trimethylsilyl, acetate, and chloride derivatives. When the hydroxyl group was thus protected or removed, all these monomers could be free radically polymerized in bulk to make soluble polymers. The chlorination reaction is complicated by the formation of 1,1‐bischloromethylacetone, which dehydrohalogenated unexpectedly to the desired α‐chloromethyl methyl vinyl ketone. HMVK will self‐condense to an ether dimer in the presence of a catalytic acid. This reagent is capable of crosslinking many alkene monomers through hydrolytically stable ether bonds. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 509–516, 2000     

Differential near-field scanning optical microscopy

We theoretically and experimentally illustrate a new apertured near-field scanning optical microscopy (NSOM) technique, termed differential NSOM (DNSOM). It involves scanning a relatively large (e.g., 0.3-2 mum wide) rectangular aperture (or a detector) in the near-field of an object and recording detected power as a function of the scanning position. The image reconstruction is achieved by taking a two-dimensional derivative of the recorded power map. Unlike conventional apertured NSOM, the size of the rectangular aperture/detector does not determine the resolution in DNSOM; instead, the resolution is practically determined by the sharpness of the corners of the rectangular aperture/detector. Principles of DNSOM can also be extended to other aperture/detector geometries such as triangles and parallelograms.     

Minimum-phase-function-based processing in frequency-domain optical coherence tomography systems

We present a simple processing technique that uses the concept of minimum-phase functions to improve frequency-domain optical coherence tomography systems. Our approach removes the autocorrelation noise and therefore increases both the accessible depth range and the recovery accuracy. To our knowledge, this is the first time that the concept of minimum-phase functions has been applied to improve optical coherence tomography.