Operation of superconducting fault current limiter using vacuum interrupter driven by electromagnetic repulsion force for commutating switch

Using conventional high‐temperature superconducting wire, a model superconducting fault current limiter (SFCL) is made and tested. Solenoid coil using Bi2223 silver sheath wire is so made that inductance is as small as possible and a vacuum interrupter is connected in series to it. A conventional reactor coil is connected in parallel. When the fault current flows in this equipment, superconducting wire is quenched and current is transferred into the parallel coil because of voltage drop of superconducting wire. This large current in parallel coil actuates magnetic repulsion mechanism of vacuum interrupter. Due to opening of vacuum interrupter, the current in superconducting wire is broken. By using this equipment, current flow time in superconducting wire can be easily minimized. On the other hand, the fault current is also easily limited by large reactance of parallel coil. © 2008 Wiley Periodicals, Inc. Electr Eng Jpn, 164(1): 52–61, 2008; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20315     

An experimental BiCMOS video 10 bit ADC

The possibility of realizing a high-quality, low-power, and low-cost video 10 bit analog-to-digital converter is examined utilizing BiCMOS circuit and process technology. A single-power-supply, 10 bit 10 MHz operation, 500 mW power dissipation, and a 4.2×6.2 mm chip size with 4200 elements were obtained     

Alzheimer’s Disease Animal Models: Elucidation of Biomarkers and Therapeutic Approaches for Cognitive Impairment

Alzheimer’s disease (AD) is an age-related and progressive neurodegenerative disorder. It is widely accepted that AD is mainly caused by the accumulation of extracellular amyloid β (Aβ) and intracellular neurofibrillary tau tangles. Aβ begins to accumulate years before the onset of cognitive impairment, suggesting that the benefit of currently available interventions would be greater if they were initiated in the early phases of AD. To understand the mechanisms of AD pathogenesis, various transgenic mouse models with an accelerated accumulation of Aβ and tau tangles have been developed. However, none of these models exhibit all pathologies present in human AD. To overcome these undesirable phenotypes, APP knock-in mice, which were presented with touchscreen-based tasks, were developed to better evaluate the efficacy of candidate therapeutics in mouse models of early-stage AD. This review assesses several AD mouse models from the aspect of biomarkers and cognitive impairment and discusses their potential as tools to provide novel AD therapeutic approaches.     

Effect of crystallization and interface formation mechanism on mechanical properties of film‐insert injection‐molded poly(propylene) (PP) film/PP substrate

A previous study has shown that the adhesion between the film and substrate of film‐insert injection‐molded poly(propylene) (PP) film/PP substrate was evident with the increases in barrel temperature and injection holding pressure. In this second part of the research work, the crystallinity at the interfacial region (i.e., region between the film and the injected substrate) was extensively studied using FTIR imaging, polarized light microscopy, and DSC in an attempt to determine the level of influence that crystallinity has on the interface and bulk mechanical properties. Consequently, a more thorough and clearer picture of the influence of the inserted film on the interfacial crystallinity and subsequently the substrate mechanical properties, such as peel strength and impact strength, has been revealed. The initial proposition that crystallinity could enhance film–substrate interfacial bonding has been confirmed, judging from the higher peel strength with increasing crystallinity at the interfacial region. Nevertheless, the change in crystallinity was not only confined to the interfacial region. With the film acting as heat‐transfer inhibitor between the injected resin and the mold wall, the total crystal structure of the substrate was substantially altered, which subsequently affected the bulk mechanical properties. The lower impact strength of film‐insert injection‐molded samples compared to that of samples without film inserts provided evidence of how the film could impart inferior properties to the substrate. The difference in cooling rate between the substrate and film might also cause other defects such as warpage and/or residual stress build‐up within the product. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 294–301, 2005     

Pervaporation membranes for ethanol–water mixture prepared by plasma polymerization. III. Perfluorocarbon membranes

Pervaporation membranes for the ethanol–water mixture were prepared by plasma polymerization of tetrafluoroethylene, perfluoropropane, and perfluoropropylene onto porous substrates. The influence of the monomers on the elemental ratio (F/C) of the polymer depositions by X-ray photoelectron spectroscopy was rather small compared with that of the W/FM parameter (W = wattage for plasma excitation, FM = mass flow rate of a monomer). The optical emission spectroscopy indicated the similarity of gaseous species formed in the plasmas. The membranes were found ethanol-permselective, showing separation coefficients (α_EtOH) around 4–7 and a wide range of permeation rates (J), 10–10^?2 kg/m² h, for the 4.8 wt % ethanol solution at 40°C. The α_EtOH of the membranes with thicker depositions could be correlated to the F/C ratios as a measure of membrane hydrophobicity. It was thought that, by making a plot α_EtOH against J values for the perfluorocarbon membranes, they could be classified into three groups on thickness of deposition. The ethanol-separation mechanisms for each group, which may contain four kinds of mass transfer schemes, i.e., distillation through larger pores, flow of sorption layer at the liquid–membrane interface, and diffusions through deposition or substrate, were also discussed.     

The effect of vacancies on the annular dark field image contrast of grain boundaries: a SrTiO(3) case study

The analysis of grain boundary structure in high resolution electron microscopy is often hindered by contrast variation within the grain boundary region which is not explained by simple models of the grain boundary structure. Recent work suggests that structural disorder along the beam direction and the presence of vacancies contribute significantly to this effect. One might expect a significant reduction in contrast in a Z-contrast image of a grain boundary would imply that vacancies present must result from the absence of heavier elements. Using a [001](210) Σ5 grain boundary in SrTiO₃ as a test case and first principles structure relaxation to calculate stable defect structures, we show that the reduction in the intensity from fully occupied Sr columns due to the structural distortion resulting from a nearby O vacancy can be as great as that due to introducing a Sr vacancy in the column itself. The effect on energy dispersive X-ray spectroscopy signals is also considered, but found to be smaller than that on Z-contrast images.     

Neutral-Ionic Transition of (BEDT-TTF)(ClMeTCNQ) Studied by ESR Under Pressure

The electron spin susceptibility of (BEDT-TTF)(ClMeTCNQ) was measured by ESR under pressure. Analysis of the susceptibility leads to the temperature dependence of the ionic fraction through the neutral-ionic phase transition, revealing that the transition is broad and continuous. It is demonstrated that this transition is crossover-like between the two phases, which can be understood by the unique double-well potential.