Influence of the intrinsic layer characteristics on a-Si:H p–i–n solar cell performance analysed by means of a computer simulation

In this paper a set of one-dimensional simulations of a-Si:H p–i–n junctions under different illumination conditions and with different intrinsic layer are presented. The simulation program ASCA permits the analysis of the internal electrical behaviour of the cell allowing a comparison among the different internal configurations determined by a change in the input set. Results about the internal electric configuration will be presented and discussed outlining their influence on the current tension characteristic curve. Considerations about the drift–diffusion and the generation–recombination balance distributions, outlined by the simulation, can be used to explain the correlation between the basic device output, the i-layer characteristics (thickness and DOS), the incident radiation intensity and photon energy.     

Development and evaluation of antimicrobial natamycin‐incorporated film in gorgonzola cheese conservation

Conservation of food products depends on product quality and packaging suitability. The objective of this work was to develop and evaluate the antimicrobial efficiency of natamycin‐incorporated film in the production process of Gorgonzola cheese. It aims to optimize the production process and increase shelf‐life and food safety for the consumer. Films with different concentrations of natamycin were produced and tested in Gorgonzola cheeses to evaluate its efficiency against Penicillium roqueforti on the cheese surface. Films with 2 and 4% natamycin presented satisfactory results for fungus inhibition and the amount of natamycin released to the cheese was below that allowed by the legislation. Copyright © 2006 John Wiley & Sons, Ltd.     

Application of Romero García method to the degradation process of DGEBA/ETDA filled with ultra fine metallic copper

Summary The thermal properties of an epoxy resin (diglycidyl ether Bisphenol A, DGEBA) cured with a primary amine (ethylenediamine, ETDA) and filled with 10, 20 and 30 wt. % of ultra fine copper particles were analyzed. The thermal results were evaluated by means of the Romero-Garcia method, which allowed to obtain the resin degradation kinetic parameters, as well as the possible decomposition mechanism. From the obtained results is possible to infer that higger copper content strongly affects the degradation process of the epoxy resin, which causes a drop off on the composites thermal stability. This behavior could be attributed to water presence, being this effect less pronounced for the resin with 10 wt. % copper and unfilled resin. Regarding to decomposition mechanism, three way transport showed the best correlation for all samples.     

The Chick Chorioallantoic Membrane Model: A New In Vivo Tool to Evaluate Breast Cancer Stem Cell Activity

The high plasticity of cancer stem-like cells (CSCs) allows them to differentiate and proliferate, specifically when xenotransplanted subcutaneously into immunocompromised mice. CSCs are highly tumorigenic, even when inoculated in small numbers. Thus, in vivo limiting dilution assays (LDA) in mice are the current gold standard method to evaluate CSC enrichment and activity. The chick embryo chorioallantoic membrane (CAM) is a low cost, naturally immune-incompetent and reproducible model widely used to evaluate the spontaneous growth of human tumor cells. Here, we established a CAM-LDA assay able to rapidly reproduce tumor specificities—in particular, the ability of the small population of CSCs to form tumors. We used a panel of organotropic metastatic breast cancer cells, which show an enrichment in a stem cell gene signature, enhanced CD44⁺/CD24^−/low cell surface expression and increased mammosphere-forming efficiency (MFE). The size of CAM-xenografted tumors correlate with the number of inoculated cancer cells, following mice xenograft growth pattern. CAM and mice tumors are histologically comparable, displaying both breast CSC markers CD44 and CD49f. Therefore, we propose a new tool for studying CSC prevalence and function—the chick CAM-LDA—a model with easy handling, accessibility, rapid growth and the absence of ethical and regulatory constraints.     

Characterization of poly(diethoxyphosphazene) by size exclusion chromatography and viscometry

Two samples of poly(diethoxyphosphazene) (PDEP) having very different molecular weights have been studied by viscometry and size exclusion chromatography in THF solution. The results obtained, together with light scattering data of these samples, allow the calculation of the Mark-Houwink constants a=0.65 and K=2.5 10^-4 in THF at 25°C. The method of calculation employed takes into account the great polydispersity of the samples. The characteristic ratio of the unperturbed dimensions was also calculated giving C_n = r²_o/n² 18, a value slightly higher than those previously reported for poly(dihexoxyphosphazene), C_n13 and poly (dichlorophosphazene), C_n13.5.     

Controlling the phase stability of polymer blends through the introduction of impenetrable interfaces

In this work, the effect of the introduction of modified solid surfaces into polymer blends on the phase‐separation process was investigated. Glass fibers with surfaces having different chemistries were introduced into polystyrene–poly(methyl methacrylate) blends. The glass fibers used either had fully hydrated surfaces or had surfaces covered with a random copolymer, poly(styrene‐co‐methyl methacrylate). The copolymer was synthesized by free‐radical polymerization of styrene and methyl methacrylate in the presence of previously vinyl silane‐treated glass fibers. The copolymerization and grafting procedures were investigated by FTIR and thermal analysis. Blends containing the fibers were studied using FTIR microscopy and optical microscopy. FTIR microscopy results showed that the composition of the phases in the blends was shifted by using fibers with different surface chemistries. Fibers with grafted copolymers were capable of narrowing the immiscibility region in the phase diagram, while fully hydrated fibers were able to expand the gap. It was proposed that interfacial interactions regulated by a hydrophilic–hydrophobic type of forces were responsible for guiding the described phase‐separation process. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 1619–1627, 2003     

Sourcing the Arab Spring: A Case Study of Andy Carvin's Sources on Twitter During the Tunisian and Egyptian Revolutions

News sourcing practices are critical as they shape from whom journalists get their information and what information they obtain, mostly from elite sources. This study evaluates whether social media platforms expand the range of actors involved in the news through a quantitative content analysis of the sources cited by NPR's Andy Carvin on Twitter during the Arab Spring. Results show that, on balance, nonelite sources had a greater representation in the content than elite sources. Alternative actors accounted for nearly half of the messages. The study points to the innovative forms of production that can emerge with new communication technologies, with the journalist as a central node trusted to authenticate and interpret news flows on social awareness streams.     

Addressing universal access in social networks: an inclusive search mechanism

Social network services (SNSs) have brought new possibilities and challenges to the design of software environments that respect people’s cultural differences. These systems may represent an opportunity for social and digital inclusion. However, search mechanisms in these systems impose serious barriers for people in the process of acquiring digital literacy. One of the barriers is the difficulty of using the adequate terms/keywords to perform content searches. This paper presents an approach to allow ordinary, non-technology proficient people to access the content of a network through the use of search parameters that make sense to them. The proposal is grounded on Semantic Web technologies (Web ontology) combined with Organizational Semiotics concepts and methods to identify the users’ profile and language. A case study was conducted with the search mechanism integrated into a SNS, and a preliminary evaluation reveals the advantages and drawbacks of the approach.     

Handling causality and schedulability when designing and prototyping cyber-physical systems

Software and Systems Modeling - Cyber physical systems are built upon digital and analog circuits, making it necessary to handle different models of computation during their design and verification...