Progressive NO2 Sensors with Rapid Alarm and Persistent Memory-Type Responses for Wide-Range Sensing Using Antimony Triselenide Nanoflakes

Antimony triselenide (Sb₂Se₃) nanoflake-based nitrogen dioxide (NO₂) sensors exhibit a progressive bifunctional gas-sensing performance, with a rapid alarm for hazardous highly concentrated gases, and an advanced memory-type function for low-concentration (<1 ppm) monitoring repeated under potentially fatal exposure. Rectangular and cuboid shaped Sb₂Se₃ nanoflakes, comprising van der Waals planes with large surface areas and covalent bond planes with small areas, can rapidly detect a wide range of NO₂ gas concentrations from 0.1 to 100 ppm. These Sb₂Se₃ nanoflakes are found to be suitable for physisorption-based gas sensing owing to their anisotropic quasi-2D crystal structure with extremely enlarged van der Waals planes, where they are humidity-insensitive and consequently exhibit an extremely stable baseline current. The Sb₂Se₃ nanoflake sensor exhibits a room-temperature/low-voltage operation, which is noticeable owing to its low energy consumption and rapid response even under a NO₂ gas flow of only 1 ppm. As a result, the Sb₂Se₃ nanoflake sensor is suitable for the development of a rapid alarm system. Furthermore, the persistent gas-sensing conductivity of the sensor with a slow decaying current can enable the development of a progressive memory-type sensor that retains the previous signal under irregular gas injection at low concentrations.     

Benchmarks of simple, generic, shaped plates for validation oflow-frequency electromagnetic computational codes

The validation of low-frequency measurements and electromagnetic (EM) scattering computations for several simple, generic shapes, such as an equilateral-triangular plate, an equilateral-triangular plate with a concentric equilateral-triangular hole, and diamond- and hexagonal-shaped plates, is discussed. The plates were constructed from a thin aluminium sheet with a thickness of 0.08 cm. EM scattering by the planar plates was measured in the experimental test range (ETR) facility of NASA Langley Research Center. The dimensions of the plates were selected such that, over the frequency range of interest, the dimensions were in the range of λ₀ to 3λ₀. In addition, the triangular plate with a triangular hole was selected to study internal-hole resonances     

The effect of biphasic waveform tilt in transvenous atrial defibrillation

Atrial defibrillation can be accomplished using low energy shocks and transvenous catheters. The biphasic waveform tilt required to achieve optimal atrial defibrillation thresholds (ADFTs) is, however, not known. The effect of single capacitor biphasic waveform tilt modification on ADFT was assessed in 20 patients. Following AF induction the defibrillation pulses were delivered between the catheters positioned in the coronary sinus and the right atrium. The single capacitor biphasic waveform shocks, delivered over the same pathways, consisted of 65% tilt (65/65 biphasic waveform) to produce an overall tilt of 88%, or 50% tilt (50/50 biphasic waveform) to produce an overall tilt of 75%. Although 65/65 biphasic waveform delivers more energy, the shorter duration 50/50 biphasic waveform reduced stored energy ADFT 21%, from 1.34 +/- 0.82 J with 65/65 biphasic to 1.06 +/- 0.81 J. These differences were not statistically significant. Nine patients had lower ADFT with 50/50 biphasic waveform while five patients had lower ADFT with 65/65 biphasic waveform. Equivalent reduction in ADFT was seen in the remaining six patients. The ADFT was 0.83 +/- 0.65 J when both tilts were considered. In conclusion, biphasic waveform tilt modification may affect the ADFT in an individual patient. The optimal biphasic waveform for ADFT is not known.     

Fast RCS computation over a frequency band using method of momentsin conjunction with asymptotic waveform evaluation technique

The method of moments (MoM) in conjunction with the asymptotic waveform evaluation (AWE) technique is applied to obtain the radar cross section (RCS) of an arbitrarily shaped three-dimensional (3-D) perfect electric conductor (PEC) body over a frequency band. The electric field integral equation (EFIE) is solved using the MoM to obtain the equivalent surface current on the PEC body. In the AWE technique, the equivalent surface current is expanded in a Taylor's series around a frequency in the desired frequency band. The Taylor series coefficients are then matched via the Pade approximation to a rational function. Using the rational function, the surface current is obtained at any frequency within the frequency range, which is in turn used to calculate the RCS of the 3-D PEC body. A rational function approximation is also obtained using the model-based parameter estimation (MBPE) method and compared with the Pade approximation. Numerical results for a square plate, a cube, and a sphere are presented over a frequency bandwidth. Good agreement between the AWE and the exact solution over the bandwidth is observed     

Artificial intelligence techniques and their application in oil and gas industry

Artificial Intelligence Review - Data are being continuously generated from various operational steps in the oil and gas industry. The recordings of these data and their proper utilization have...     

The influence of charge density and steric factor of aminated chloromethyl polystyrene homologs in bilirubin adsorption

Bilirubin, a bile pigment, was studied for its extent of adsorption on substituted aminechloromethyl polystyrene by UV spectrophotometry. By performing simple displacement reactions on chloromethyl polystyrene with secondary and tertiary amines, the amount of charge density and steric factor on substituted nitrogen atom have been varied. Adsorption isotherms of bilirubin at 0°C by different amine–chloromethyl polystyrene homologs suggest the existence of electrostatic interaction of polymeric resin with bilirubin moiety. Results of adsorption of bilirubin to polymeric resin have shown that the extent of adsorption of bilirubin depends on the unit charge, and on the structure of the substituted amine–chloromethyl polystyrene. The effects of porosity of resin on bilirubin adsorption have also been discussed.     

MODELING AND PREDICTIVE CONTROL OF MIMO NONLINEAR SYSTEMS USING WIENER-LAGUERRE MODELS

In this work, a Weiner-type nonlinear black box model was developed for capturing dynamics of open loop stable MIMO nonlinear systems with deterministic inputs. The linear dynamic component of the model was parameterized using orthogonal Laguerre filters while the nonlinear state output map was constructed either using quadratic polynomial functions or artificial neural networks. The properties of the resulting model, such as open loop stability and steady-state behavior, are discussed in detail. The identified Weiner-Laguerre model was further used to formulate a nonlinear model predictive control (NMPC) scheme. The efficacy of the proposed modeling and control scheme was demonstrated using two benchmark control problems: (a) a simulation study involving control of a continuously operated fermenter at its optimum (singular) operating point and (b) experimental verification involving control of pH at the critical point of a neutralization process. It was observed that the proposed Weiner-Laguerre model is able to capture both the dynamic and steady-state characteristics of the continuous fermenter as well as the neutralization process reasonably accurately over wide operating ranges. The proposed NMPC scheme achieved a smooth transition from a suboptimal operating point to the optimum (singular) operating point of the fermenter without causing large variation in manipulated inputs. The proposed NMPC scheme was also found to be robust in the face of moderate perturbation in the unmeasured disturbances. In the case of experimental verification using the neutralization process, the proposed control scheme was found to achieve much faster transition to a set point close to the critical point when compared to a conventional gain-scheduled PID controller.     

Kinetics of hydroformylation of 1-decene using homogeneous HRh(CO)(PPh3)3 catalyst: a molecular level approach

The kinetics of hydroformylation of 1-decene using homogenous HRh(CO)(PPh₃)₃ catalyst has been reported in the temperature range of 50–70 °C. The effect of catalyst,P _{H 2},P _CO, and 1-decene concentration on the rate of hydroformylation has been studied. Based on the analysis of initial rate data, a rate equation has been proposed and kinetic parameters evaluated. The activation energy was found to be 11.76 kcal/mol. A molecular level approach to kinetic modelling has also been illustrated. The rate equation derived assuming oxidative addition of H₂ as a rate determining step, has been found to represent the data satisfactorily. The rate parameters for the mechanistic model have been evaluated for the data at 60 °C.NCL Communication No. 5735.