The effect of fibre orientation of the dry sliding wear of borsic-reinforced 2014 aluminium alloy

The effect of fibre orientation on the dry sliding wear of continuous B(SiC) fibre reinforced aluminium alloy composites was investigated using a pin-on-disc wear testing machine. The metal-matrix composites (MMC) samples were tested in the normal (N), parallel (P) and antiparallel (AP) orientations sliding against a steel counter disc at a fixed speed of 1 m s^–1 under loads of from 12 to 60 N.The results showed that for the matrix alloy and MMCs, the average wear increased linearly with load. Wear of the MMCs was insensitive to fibre content but for composites with fibre contents at or above the minimum of 16 vol% used for this work, the wear rate was about 18% of that of the unreinforced matrix. Fibre orientation had a minor effect on wear rate; the N orientation gave the lowest wear rate with the AP orientation slightly higher and the P orientation significantly higher.The average coefficients of friction of the MMCs in N and AP orientations decreased linearly with increased wear rate and non-linearly with increased load, but the P orientation was insensitive to either variable.It was concluded from these results and a metallographic examination that the mechanism of wear of MMCs was essentially oxidative wear of the matrix. The hard fibres modified this to slightly different degrees depending on their orientation relative to the wear surface and sliding direction.     

Thermodynamic analysis of solar photovoltaic cell systems

The thermodynamic characteristics of solar photovoltaic (PV) cells are investigated from a perspective based on exergy. A new efficiency is developed that is useful in studying PV performance and possible improvements. Exergy analysis is applied to a PV system and its components, and exergy flows, losses and efficiencies are evaluated. Energy efficiency is seen to vary between 7% and 12% during the day. In contrast, exergy efficiencies, which incorporate the second law of thermodynamics and account for solar irradiation exergy values, are lower for electricity generation using the considered PV system, ranging from 2% to 8%. Values of “fill factors” are determined for the system and observed to be similar to values of exergy efficiency.     

Oxidation behavior of single-crystal Al2O3-fiber-reinforced Ni3Al-based composites

A series of single-crystal Al₂O₃-fiber-reinforced Ni3Al-based intermetallic matrix composites were fabricated by pressure casting. The matrices employed were binary Ni₃Al, Ni₃Al-0.5 at. pct Cr, and Ni₃Al-0.34 at. pct Zr. The development of microstructure upon oxidation in air at either 1100 °C or 1200 °C was investigated by optical, scanning, and transmission electron microscopy. In air-oxidized binary Ni₃Al, some of the fibers were fully or partially covered with a layer of oxide. A weak fiber/matrix bond in this system, which led to fiber debonding during composite processing, is believed to be responsible for the ingress of O into the composite and oxidation of the matrix in the debonded regions at the fiber/matrix interface. Addition of Cr to Ni₃Al resulted in an almost threefold increase in fiber/matrix bond strength. No oxidation of the interface was observed. A thick layer of oxide was formed around all the fibers when the composite was thermally cycled prior to isothermal annealing. Addition of Zr to Ni₃Al resulted in the formation of a layer of ZrO₂ on the surface of the fibers during composite processing. The ZrO₂ layer provided a fast path for the diffusion of O, which led to the formation of a rootlike oxide structure around the fibers. The rootlike structure consisted of a network of Al₂O₃-covered ZrO₂.     

The IFR/DFR property of the forward recurrence-time distribution

When a failure or replacement process is modeled as a renewal process, the residual life of the unit in use at a given time is generally referred to as the forward recurrence time (RT). Distributional properties of this random variable are critically important in many applications. This paper investigates the extent to which the failure-rate function monotonicity of a life distribution is inherited by the forward RT distribution at time s of its renewal process. For DFR life distributions, the forward RT distribution is also DFR for every s⩾0. However, the corresponding property does not necessarily hold for IFR life distributions. The forward RT distribution is IFR in the limit as s→0 and as s→∞. For IFR Weibull life distributions, we demonstrate numerically that the forward RT distribution is IFR for small s. As s is increased, it alternates between being IFR and non-IFR in an interesting cyclical pattern, and remains IFR beyond a large enough s     

Film morphology and reaction rate for the CVD of tungsten by the WF6—SiH4 reaction

Journal of Electronic Materials - Low pressure chemical vapor deposition (LPCVD) of tungsten (W) by SiH4 reduction of WF6 on Si(100) surfaces was studied in a single-wafer, cold-wall reactor over a...     

Salt and pepper noise filtering with fuzzy-cellular automata

A new image denoising algorithm is proposed to restore digital images corrupted by impulse noise. It is based on two dimensional cellular automata (CA) with the help of fuzzy logic theory. The algorithm describes a local fuzzy transition rule which gives a membership value to the corrupted pixel neighborhood and assigns next state value as a central pixel value. The proposed method removes the noise effectively even at noise level as high as 90%. Extensive simulations show that the proposed algorithm provides better performance than many of the existing filters in terms of noise suppression and detail preservation. Also, qualitative and quantitative measures of the image produce better results on different images compared with the other algorithms.     

Fractionation of transgenic corn for recovery of recombinant enzymes

Two germ-separation methods, dry-milling and density separation by flotation, were evaluated for recovering recombinant β-glucuronidase (rGUS) that accumulated primarily in the germ of transgenic corn. The dry-milling process consisted of (i) seed tempering, (ii) degerming with a horizontal-drum degermer/dehuller, (iii) particle size fractionation with standard sieves, (iv) germ and endosperm separation by roller milling and sifting, and (v) removal of hulls by aspiration. Sieves nos. 5, 6, and 7 retained the majority of germ, and subfractions from these sieves were pooled as a germ-rich fraction. Mass balances showed that the germ-rich fraction, which constituted 17% of the total dry-milled corn weight, contained 49% of rGUS activity and 64% of the total recoverable oil. Germ fractionation by flotation was tested as a proof-of-concept method aimed at separating corn fractions based on their difference in specific gravity (sp gr). The process consisted of impact-grinding of corn kernels followed by density separation using 1.15 or 1.3 specific gravity sodium nitrate solution. The oil-containing germ fraction floated, whereas the heavier endosperm fraction sedimented. The flotation method was simpler and resulted in higher enzyme recovery, that is, the germ-rich fraction was 20% (w/w) of the initial corn weight, and accounted for 80% of rGUS activity and 77% of total oil. The sodium nitrate solution did not have an adverse effect on the enzyme activity.     

Noise analysis of robot manipulator using neural networks

Due to a lot of robot manipulators application in industry, low noise degree is very important criteria for robot manipulator's joints. In this paper, joint noise problem of a robot manipulator with five joints is investigated both theoretically and experimentally. The investigation is consisted of two steps. First step is to analyze the noise of joints using a hardware and software. The hardware is a part of noise sensors. The second step; according to experimental results, some neural networks are employed for finding robust neural noise analyzer. Five types of neural networks are used to compare each other. From the results, it is noted that the proposed RBFNN gives the best results for analyzing joint noise of the robot manipulator.     

Approximate periodic solutions for the Helmholtz-Duffing equation

Approximate periodic solutions for the Helmholtz-Duffing oscillator are obtained in this paper. He’s Energy Balance Method (HEBM) and He’s Frequency Amplitude Formulation (HFAF) are adopted as the solution methods. Oscillation natural frequencies are analytically analyzed. Error analysis is carried out and accuracy of the solution methods is evaluated.