Studies on the structural and ionic transport properties at elevated temperatures of La1−xMnO3±δ synthesized by a wet chemical method

Structural transformation and ionic transport properties are investigated on wet-chemically synthesized La_1−xMnO₃ (x=0.0–0.18) compositions. Powders annealed in oxygen/air at 1000–1080 K exhibit cubic symmetry and transform to rhombohedral on annealing at 1173–1573 K in air/oxygen. Annealing above 1773 K in air or in argon/helium at 1473 K stabilized distorted rhombohedral or orthorhombic symmetry. Structural transformations are confirmed from XRD and TEM studies. The total conductivity of sintered disks, measured by four-probe technique, ranges from 5 S cm⁻¹ at 298 K to 105 S cm⁻¹ at 1273 K. The ionic conductivity measured by blocking electrode technique ranges from 1.0×10⁻⁶ S cm⁻¹ at 700 K to 2.0×10⁻³ S cm⁻¹ at 1273 K. The ionic transference number of these compositions ranges from 3.0×10⁻⁵ to 5.0×10⁻⁵ at 1273 K. The activation energy deduced from experimental data for ionic conduction and ionic migration is 1.03–1.10 and 0.80–1.00 eV, respectively. The activation energy of formation, association and migration of vacancies ranges from 1.07 to 1.44 eV.     

Stability of Fe3+ — VO defect pairs in polycrystalline Pb(Ti,Zr)O3

The intensity of the EPR signal with g = 5.985 arising from a ferric ion — oxygen vacancy defect pair (Fe³⁺ — V_O) in PbTiO₃, varies with the extent of PbO nonstoichiometry at constant Fe³⁺ content due to an increased oxygen vacancy concentration. In PZT solid solutions, the signal intensity decreases with an increase in Zr. A lower intensity is also noticed for Fe³⁺ — V_O signals in PbZrO₃. This behaviour is explained on the basis of PbO nonstoichiometry arising from independent Pb- and O-vacancies as well as the randomly distributed crystallographic shear (CS) plane defects. The contribution to PbO nonstoichiometry from CS planes is larger in high zirconium compositions of PZT.     

A comparative study of short nylon fiber—Natural rubber composites prepared from dry rubber and latex masterbatch

A novel method for the preparation of short nylon fiber–natural rubber composites was developed in which short fibers chopped to approximately 6 mm were incorporated in the latex stage and processed into sheet form. By this method, mixing cycle time was reduced without compromising the fiber dispersion. Fiber breakage during mixing was reduced. The new composites when compounded with a dry bonding system based on hexamethylenetetramine, resorcinol and hydrated silica (HRH) showed improved modulus, tensile strength and abrasion resistance compared to conventional composites. Tear strength, resilience, and compression set were similar to the conventional composites. SEM analysis indicated better interaction between matrix and fibers in the case of latex master batch. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Evaluation of hot hardness and creep of a 350 grade commercial maraging steel

The hardening response and the indentation creep of a 350 grade commercial maraging steel were evaluated using a hot hardness tester. The hardness versus temperature plot exhibited three distinct regions. Hardness response was noted between 500–800 K. The unusually high values of activation energy and stress exponent obtained during the creep experiment could be rationalized by a novel concept of introducing a back stress term in the indentation creep relation. The corrected value of the activation energy was found to be reasonably in agreement with the activation energy for diffusion of Ni in iron. Results are supplemented with microstructural observation.     

Microstructure evolution during batch annealing

Design of industrial annealing cycles requires recrystallization and grain growth studies, which are typically carried out under isothermal laboratory condition. The kinetics coefficients of these phase transformations are obtained from such studies, which are subsequently used in designing the industrial nonisothermal cycles using the additivity principles. However, the strong heating rate effects on the grain growth kinetics necessitate such kinetics studies using industrial thermal profiles. In the present work, the hot and cold spot cycles of an industrial batch annealing cycle for AIK grade steel have been simulated in a programmable laboratory furnace. Subsequently, the effect of annealing temperature, soaking time, and heating rate on the microstructural features, such as grain size distribution, grain shape anisotropy, and grain orientation, have been investigated through extensive quantitative microscopy. The implications of these results on the design of industrial batch annealing cycles have been discussed.     

Influence of Bi3+ ions in enhancing the magnitude of positive temperature coefficients of resistance in n-BaTiO3 ceramics

Bi³⁺ ions substituting at Ba-sites in a limited concentration range with another donor dopant occupying the Ti-sites in polycrystalline BaTiO₃ enhanced the positive temperature coefficient of resistance (PTCR) by over seven orders of magnitude. These ceramics did not require normal post sinter annealing or a change to an oxygen atmosphere during annealing. These ceramics had low porosities coupled with better stabilities to large applied electric fields and chemically reducing atmospheres. Bi³⁺ ions limited the grain growth to less than 8 m in size, they enhanced the concentration of acceptor-type trap centres at the grain-boundary-layer regions and maintained complete tetragonality at low grain sizes in BaTiO₃ ceramics.     

Performance of orthogonal frequency division multiplexing based M-ary quadrature amplitude modulation in asymmetrical dual-hop mixed RF-FSO transmission system

This paper investigates the performance of a dual-hop mixed relay system with radio frequency (RF) and free-space optics (FSO) communication under the effect of pointing error (PE) and atmospheric turbulence (AT). This paper considers a system where RF and FSO links are cascaded. The RF link is modeled by Nakagami-m fading, and the FSO link is modeled as gamma–gamma (G-G) fading channel. Both the channel models use orthogonal frequency division multiplexing (OFDM) with M-ary quadrature amplitude modulation (QAM). The expressions for probability density function, cumulative distribution function, signal-to-noise ratio, and ergodic capacity are derived. The moment generating function (MGF) of fading and the bit error rate (BER) of the OFDM-based M-ary QAM scheme is derived in terms of Meijer's G-function. It has been observed that, in fixed gain relay systems, the modulation scheme's BER is dominated by the SNR of the RF link. While in a variable gain relay system, the turbulence conditions of the FSO system affect the SNR and the BER of the modulation method. The feasibility of heterodyne detection and intensity modulation direct detection (IM/DD) is analyzed in terms of outage probability and ergodic capacity. The results can be used to choose the optimal modulation order and relay system for QAM-OFDM-based optical wireless systems.     

Characterization and densification studies on ThO2-UO2 pellets derived from ThO2 and U3O8 powders

ThO₂ containing around 2-3% ²³³UO₂ is the proposed fuel for the forthcoming Indian Advanced Heavy Water Reactor (AHWR). This fuel is prepared by powder metallurgy technique using ThO₂ and U₃O₈ powders as the starting material. The densification behaviour of the fuel was evaluated using a high temperature dilatometer in four different atmospheres Ar, Ar-8%H₂, CO₂ and air. Air was found to be the best medium for sintering among them. For Ar and Ar-8%H₂ atmospheres, the former gave a slightly higher densification. Thermogravimetric studies carried out on ThO₂-2%U₃O₈ granules in air showed a continuous decrease in weight up to 1500 °C. The effectiveness of U₃O₈ in enhancing the sintering of ThO₂ has been established.     

Corrosion inhibition of mild steel in 1 M HCl using Tamarindus indica extract: electrochemical,surface and spectroscopic studies

Abstract

We report, here, the corrosion inhibition of mild steel specimen in 1?M HCl by tamarind fruit pulp aqueous (TFPA) extract. The inhibition property in the presence of TFPA extract is studied using weight loss, polarization measurement and electrochemical impedance spectroscopy (EIS). The inhibitor efficiency is found to vary from 74% to 88% (weight loss method) with TFPA concentration of 100–600?ppm. The reduction in Tafel slopes shows that TFPA acts as a mixed-type inhibitor. The adsorption of the inhibitor on the metal surface follows Langmuir isotherm. The standard Gibbs free energy of adsorption value of –40?kJ/mol suggests the chemisorption of inhibitor molecules via coordinate bond. AFM results exhibit a decrease in the surface roughness of mild steel, exposed to 1?M HCl from 299?±?12 to 154?±?6.6?nm, with increasing concentration of inhibitor from 0 to 600?ppm due to the uniform coverage of inhibitor molecules on the metal surface. X-ray photoelectron spectroscopy de-convoluted high resolution profiles of C 1?s (carbon) for mild steel exposed to 1?M HCl with 600?ppm inhibitor show major peaks corresponding to sp³ C–C/C–H (284.9?eV) and oxygen bondings in C–OH, C=O, COOH with a binding energy of 285.9, 286.9, 288.5?eV, respectively, thereby confirming the adsorption of organic moieties on mild steel surface. Fourier transform infrared spectroscopy further confirms the adsorption of inhibitor molecules on the metal surface. Therefore, tamarind fruit pulp extract is a potential corrosion inhibitor for mild steel, which is cost-effective, green and non-toxic.