A new design strategy for DC/DC LLC resonant converter: Concept,modeling, and fabrication

In this paper, a new design procedure for LLC converter has been introduced. In fact, this method is a computer-based design algorithm based on a numerical technique. In the process of designing, the value of the resonant element is obtained by solving the LLC converter fundamental equation. This converter will be controlled by using state feedback, such as output voltage variable. As a matter of fact, in a control system, the change of output voltage (because of load variation) will affect the switching frequency, so the output voltage will be tuned. In the designing process, the fundamental equations of LLC converter are obtained, and the value of the resonant elements is calculated. Also, a comparison analysis is carried out between the proposed and typical methods. The simulation is done to investigate the validity of the proposed method. Moreover, a prototype is manufactured, and the experimental test is done to evaluate its applicability.     

On the off-design of a natural gas-fired combined cycle with CO2 capture

During the last 15 years cycles with CO₂ capture have been in focus, due to the growing concern over our climate. Often, a natural gas fired combined cycle with a chemical absorption plant for CO₂ capture from the flue gases have been used as a reference in comparisons between cycles. Neither the integration of the steam production for regeneration of amines in the combined cycle nor the off-design behaviour of such a plant has been extensively studied before.     

Low temperature J-resistance curve determination of asphalt concrete using wavelet-Radon transform

A single specimen test using the three point single edge notched beam configuration at low temperatures for obtaining hot mix asphalt （HMA） resistance curves is developed.Resistance curves are obtained for mixtures at six temperature levels of＋5,0,-5,-10,-15,and-20 ℃ and three binder contents of 4％,4.5％,and 5％.Crack extension increments during the test are measured by means of an image processing technique using Radon transform and feature extraction.All the specimens exhibit a rising R-curve,indicating ductility and toughening mechanisms in the ductile-quasi brittle fracture of the mixture.It is observed that the reduction of temperature results in a further tendency of the mixture for unstable crack growth and less subcritical crack length.It is also shown that using the binarization process,an automatic index can be developed that can represent the extent of brittleness and extent of the low temperature in which the cracking has occurred.     

Solidification crack initiation and propagation in pulsed laser welding of wrought heat treatable aluminium alloy

The effect of preheating on strain rate and liquid flowrate is analysed to develop a model for solidification cracking in successive laser weld spots in 2024 aluminium alloy. It is shown that the lower tendency for solidification cracking with preheating can be attributed to the lower strain rate but not the feeding rate. It is also shown there is a strong tendency for solidification crack propagation through the fusion lines between the consecutive weld spots where there is already a crack present at the fusion line. This observation can be attributed to the higher local strain rate and lower feeding rate.     

Ab initio study of phase stability in doped TiO2

Ab initio density functional theory calculations of the relative stability of the anatase and rutile polymorphs of TiO₂ were carried out using all-electron atomic orbitals methods with local density approximation. The rutile phase exhibited a moderate margin of stability of ~ 3 meV relative to the anatase phase in pristine material. From computational analysis of the formation energies of Si, Al, Fe and F dopants of various charge states across different Fermi level energies in anatase and in rutile, it was found that the cationic dopants are most stable in Ti substitutional lattice positions while formation energy is minimised for F^? doping in interstitial positions. All dopants were found to considerably stabilise anatase relative to the rutile phase, suggesting the anatase to rutile phase transformation is inhibited in such systems with the dopants ranked F?>?Si?>?Fe?>?Al in order of anatase stabilisation strength. Al and Fe dopants were found to act as shallow acceptors with charge compensation achieved through the formation of mobile carriers rather than the formation of anion vacancies.     

Phase-field modelling of self-propagating high-temperature synthesis of NiAl

A phase-field model is developed and used to simulate high-temperature synthesis of intermetallic compounds. The model is based on a thermodynamic formulation, which incorporates the formation of chemically ordered phases and the associated heat generation. In contrast to previous approaches to modelling of high-temperature synthesis of intermetallics, the present model can be used to analyse the kinetics of the process at the microstructure level. The model takes general thermodynamic and kinetic parameters as input and gives as output a spatially resolved sequence of phase formation, from which the overall reaction kinetics can be inferred. Thus, no additional assumption has to be made on the nature of the kinetic mechanisms or on the magnitude of the overall reaction rate. Beside prediction of the microstructure, the model captures the key thermal characteristics of the combustion synthesis in both modes of thermal explosion and self-propagation. The results of simulations, as applied to the case of intermetallic formation in a simplified Ni–Al system, are shown to be consistent with the existing experimental data.     

Modeling dynamic viscosity of n-alkanes using LSSVM technique

One of the important thermophysical properties is viscosity which expresses the resistance of fluid to flow. The least squares support vector machine (LSSVM) algorithm is proposed as a novel method for prediction of dynamic viscosity of different normal alkanes in a wide range of pressure and temperature. As this study is purely computational, 228 experimental data points were gathered from literature for training and validation of the model. The outcomes of the LSSVM algorithm were compared with the actual data with acceptable average absolute relative deviation and the coefficient of determination (R²) of 1.014 and 0.9968, respectively. The comparisons showed that the predicting model has the potential of prediction of n-alkane dynamic viscosity in terms of pressure, temperature, and carbon number of n-alkane, so this strategy can be used as a simple tool for predicting the behavior of reservoir fluids.     

Study of the behavior of mechanically stabilized earth (MSE) walls subjected to differential settlements

The limit equilibrium (LE) analysis has been used to design MSE walls. Presumably, the deflection of MSE walls can be limited to an acceptable range by ensuring sufficient factors of safety (FOSs) for both external and internal stabilities. However, unexpected ground movements, such as movements induced by excavations, volume changes of expansive soils, collapse of sinkholes, and consolidations of underlying soils, can induce excessive differential settlements that may influence both the stability and the serviceability of MSE walls. In this study, a numerical model, which was calibrated by triaxial tests and further by a specially-designed MSE wall tests, investigated the behavior of an MSE wall as well as the influence of various factors on the performance of the MSE wall when the wall facing settled relatively to the reinforced zone. The numerical results showed that the differential settlement would cause substantial vertical and horizontal movements for the MSE wall, as well as an increase in lateral earth pressure and geosynthetic reinforcement strain. The maximum horizontal movement and increase of the lateral earth pressure occurred at about 1.0 m above the toe. The differential settlement resulted in a critical plane that coincided with the plane of 45°+?/2. The maximum increase of the strain for each geogrid layer occurred in that plane, and the bottom layer had the greatest strain increase among all layers of reinforcement. The study further indicated that the surcharge, backfill friction angle, tensile stiffness of geogrid, reinforcement length and MSE wall height had noticeable influences on horizontal and vertical movements, and strain in geosynthetics. According to the results, the MSE wall that had a higher factor of safety would have less movements and geosynthetic strain increase. In contrast, only the friction angle, tensile stiffness and MSE wall height showed some degree of influence on the lateral earth pressure due to differential settlements.     

A waste heat recovery system development and analysis using ORC for the energy efficiency improvement in aluminium electrolysis cells

The present work investigates an active waste heat recovery system for the side walls of the aluminium electrolysis cells, enabling utilization of the extracted heat in power generation. This will potentially lead to energy efficiency improvement in the primary aluminium production industry and an enhanced aluminium production rate. An experimentally validated loop thermosyphon heat pipe model was used for heat extraction from the cell side wall. Boosting system thermal efficiency through waste heat recovery, by means of a heat utilization system, and increasing the level of control, as well as thermal equilibrium, stand as the main addressed objectives of the current study, which consequently result in an increased aluminium production rate. An organic Rankine cycle is incorporated into the system, and its performance is evaluated, taking into consideration the operating situations in terms of available temperature and thermal power range.     

Evaluation of the reproductive and developmental safety of cysteamine in the rat: effects on female reproduction and early embryonic development

Cystinosis is an autosomal recessive metabolic disease in which the amino acid cystine accumulates in lysosomes due to a defect in lysosomal cystine transport. Cystinosis in infancy is associated with poor growth, muscle wastage, and death at about age 10 due to kidney failure. Treatment with cysteamine and kidney transplantation enables cystinotic girls to reach reproductive age and to be healthy enough to permit pregnancy. It is not known whether exposure to cysteamine will have adverse effects on reproduction in the human. It is also possible that some of the complications seen in cystinotic children could be avoided if a pregnant woman carrying a cystinotic fetus were given cysteamine. However, this treatment is not likely to occur until therapeutic exposures to cysteamine are judged to present no increased risk to the human fetus. As part of a larger investigation assessing the reproductive and developmental safety of cysteamine (as phosphocysteamine) using the rat, the two studies reported herein were performed. The first, a dose-finding study, led to the selection of 150 mg/kg/day as the highest dose of cysteamine used for the second and primary focus of this report. The second study involved the exposure of female rats to cysteamine from premating through day 6.5 postconception and assessment of female fertility and early embryonic development. Cysteamine was administered orally in doses of 0, 37.5, 75, 100, or 150 mg/kg/day. There were no clinical signs of maternal toxicity during the exposures of 2 to 5 weeks before successful mating. Animals in the 150 mg/kg/day group experienced a nonsignificant decrease in body weight gain during pregnancy to day 6.5 postconception, a significant increase in liver and spleen weights, and a significant increase in days to coitus--suggesting that a low level of toxicity was manifested. However, there were no adverse effects on reproductive performance with respect to conception and early embryonic development.