Synthesis, absolute configuration, and analysis of malathion, malaoxon, and isomalathion enantiomers

Syntheses of the enantiomers of malathion, malaoxon, and isomalathion are reported herein. Malathion enantiomers were prepared from (R)- or (S)-malic acid in three steps. Enantiomers of malathion were converted to the corresponding enantiomers of malaoxon in 52% yield by oxidation with monoperoxyphthalic acid, magnesium salt. The four isomalathion stereoisomers were prepared via two independent pathways using strychnine to resolve the asymmetric phosphorus moiety. The absolute configurations of the four stereoisomers of isomalathion were determined by X-ray crystallographic analysis of an alkaloid salt precursor. A high-performance liquid chromatography technique was developed to resolve the four stereoisomers of isomalathion, and to determine their stereoisomeric ratios.     

Limit of validity of the moisture diffusivity for the study of moisture transfer inside terracotta

In order to know the limit of validity of the concept of hydrical diffusivity, D_W, we tried to validate the Boltzmann's method used to identify it. We show that for a medium strictly satisfying the equation of diffusion, the method gives quite good results with nevertheless some inaccuracies for the extreme values of water contents. For the real studied material, a backed clay, its identification becomes more difficult because of the dispersion of the wetting phenomenon observed for different specimens of the same material. We are showing that the mean behaviour of one sample is near to be the same as the more probable behaviour of all the samples. Otherwise the values of D_W determined for a wetting cannot be used to describe a drying process. It practical interest is then considerably reduced. In order to test the influence of the gas phase pressure effects on the behaviour of the material, we have determined all the parameters necessary to describe, numerically, wetting and drying processes without to resort to D_W. We noticed an overpressure of the gas phase inside the material due to drying. If the gas pressure effects are, numerically, switched off, we cannot notice any influence on water content profiles for this type of material.     

In situ regeneration of the Ni-based catalytic reformer of a 5 kW PEMFC system

The paper reports the results of on-site regeneration catalytic bed of the natural gas reformer in a 5 kW PEM fuel cell system. The Ni catalyst previously poisoned by sulphur from the available natural gas, could be re-activated by injection of pure water steam, following the method developed for industrial reformers using the same metal catalyst: this method was shown to be perfectly efficient, provided no natural gas was fed during the operation. Results of the tests conducted are presented and discussed in relation to published data on S-sorption on Ni surfaces.     

Toward a unified theory of similarity and recognition.

A new theory of similarity, rooted in the detection and recognition literatures, is developed. The general recognition theory assumes that the perceptual effect of a stimulus is random but that on any single trial it can be represented as a point in a multidimensional space. Similarity is a function of the overlap of perceptual distributions. It is shown that the general recognition theory contains Euclidean distance models of similarity as a special case but that unlike them, it is not constrained by any distance axioms. Three experiments are reported that test the empirical validity of the theory. In these experiments the general recognition theory accounts for similarity data as well as the currently popular similarity theories do, and it accounts for identification data as well as the longstanding "champion" identification model does. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

New integrated buried laser-ridge modulator with identical active layer

Integrated laser modulators are attractive devices for wavelength-division-multiplexing optical systems due to their compactness, high output power, and low cost. Their fabrication simplicity is a way to decrease further the transmitter cost and address new opening markets of short range and metropolitan networks. We report a new integration scheme electroabsorption-modulator distributed feedback (DFB) laser based on well-established industrial solutions for discrete buried ridge (BRS) DFB lasers and discrete shallow ridge modulators. Processing simplification with an identical active layer has been possible due to a good behavior of strongly positively detuned BRS lasers. The integrated devices demonstrated 30-dB extinction ratio with 10-GHz bandwidth and P/sub out/=10 dBm for emission in 1.55-/spl mu/m range.     

SMC composites waste management as reinforcing fillers in polypropylene by combination of mechanical and chemical recycling processes

A new process of management of waste of composite materials from Sheet Moulding Compounds (SMC), as reinforcing fillers for thermoplastic materials, including both mechanical and chemical processes is proposed in this paper. Communited SMC being composed of coated glass fibres intimately mixed with calcium carbonate powder, their reinforcing power is low. First, the fibrous part was increased by partial dissolution of calcium carbonate present in the crushed products SMC. Second, a process of partial solvolysis was developed aiming at strong increasing the interfacial mechanical properties by functionalising of SMC load incorporated into polypropylene/grafted maleic anhydride polypropylene (PP/PP_gma). At this effect, we investigated a treatment with a hot triamine (diethylenetriamine, DETA) in order to create a functionalisation, after scission of the bond ester of unsaturated polyester, as bridging amino-succinimide.The effect of this recycling way by partial solvolysis was checked from the mechanical properties of the resulting reinforced PP/PP_gma material: Although a lower of Young modulus, better yield stress and especially resilience were observed.     

Life extension technology for steam pipe systems—I. Development of material properties

Material properties of A106B low-carbon steels were developed for life prediction analyses of steam pipes operated at elevated temperatures but in the sub-creep temperature range. Tensile, fracture toughness, fatigue crack growth rate and low-cycle fatigue properties were obtained on the piping steel at 24°C (75°F) and 288°C (550°F). The latter temperature corresponded to the highest operating temperature of nuclear plant steam piping. Increasing the test temperature from 24°C (75°F) to 288°C (550°F) decreased the yield strength and fracture toughness of the steel. Fatigue crack propagation rate properties at 24°C (75°F) and 288°C (550°F) were found to be comparable.

In the low-cycle fatigue tests, below a strain amplitude level of approximately 0.5%, cyclic softening was observed, while at higher strain levels, cyclic hardening was present. Based on the results of tensile and incremental-step fatigue testing, the strain-life curve was predicted. The predicted strain-life curve was found to be in agreement with the experimental result.

The fracture surfaces of fracture toughness specimens showed ductile fracture, while striations were observed on those of fatigue crack growth specimens. Fatigue striations were also observed on the fracture surfaces of low-cycle fatigue specimens. Fatigue initiation was associated with inclusions. It was shown that plastic straining in A106B steel could be detected by acoustic emission and by monitoring the eddy current response. These nondestructive evaluation techniques exhibit possibilities for in-situ monitoring of fatigue deformation.

While the development of material properties for the life prediction assessment of steam pipes is included in Part I of this paper, the establishment of a quantitative life prediction methodology and inspection criteria is contained in Part II. The developed life prediction methodology quantifies the effects of operating parameters on the remaining life of steam pipes using the material properties obtained in Part I.     

Large induction motor anti-friction bearing selection

The majority of motor specifications utilize L₁₀ life as the sole selection criterion for anti-friction bearings. At times, L ₁₀ lives in excess of 100,000 hours are specified in an attempt to prevent recurring field problems when the failures are originating from nonL₁₀ mechanisms. In some cases, these failures occur indirectly from overspecifying L₁₀ life. Some general examples of this occurence are described. A successful bearing design requires the consideration of many equally important factors, which are discussed in this article