Mechanism of Springback-Free Bending of High-Strength Steel Sheets under Warm Forming Conditions

Tensile loading-unloading tests of high-strength steel sheets in an elevated temperature range are conducted using a 100 kN servo-controlled hydraulic dynamic fatigue testing machine, aiming at clarifying the mechanism of the springback-free phenomenon occurring in warm sheet forming. From stress-strain curves obtained by the tests, it is found that the abrupt decrease in the springback of formed steel sheets at approximately 750 K in isothermal v-bending tests is mainly caused by high-temperature transient creep deformation. Also, from the results obtained by the isothermal v-bending test, bending-unbending deformation observed at temperatures higher than 750 K, as a result of high-temperature creep, was found to have a secondary effect in the springback-free phenomenon.     

Developing a Higher-Cycled Product Design CAE Model： The Evolution of Automotive Product Design and CAE

To help corporations survive amidst worldwide quality competition, the authors have focused on the strategic development of a higher-cycled product design CAE model employing a highly reliable CAE analysis technology component model. Their efforts are part of principle-based research aimed at evolving product design and CAE development processes to ensure better quality assurance. To satisfy the requirements of developing and producing high quality products while also reducing costs and shortening development times, the effectiveness of this model was verified by successfully applying it to the technological problems of loosening bolts and other product design bottlenecks at auto manufacturers.     

Magnetically coupled oscillators applicable to high-sensitivity mass detection

Microsystem Technologies - In this paper, a system of magnetically coupled oscillators consisting of a Π-shaped horizontal cantilever and a rectangular vertical cantilever with a frequency...     

Inhibition of char deposition using a particle bed in heating section of supercritical water gasification

Supercritical water gasification (SCWG) has attracted attention as a technology for utilizing wet biomass. We used a fluidized bed of alumina particles to prevent blockage of a SCWG reactor. A glucose solution was heated in the reactor with and without fluidized alumina particles. In the absence of alumina particles, char particles formed homogeneously in the reactor, but the use of a fluidized bed resulted in accumulation of char particles at the reactor’s exit rather than inside the reactor. Therefore, the fluidized bed was effective at preventing blockage of the reactor. However, the alumina particles did not remove deposits from the reactor’s walls. Instead, the fluidized bed caused larger char particles to form, preventing their adhesion to the reactor’s wall.     

Synthesis of polyamide-hydroxyapatite nanocomposites

Simultaneous one-pot syntheses of PA66 and HAp were carried out by extracting H₂O and CO₂ from PA66 monomers and HAp raw materials, respectively, resulting in the formation of a polyamide (PA) 66-hydroxyapatite (HAp) nanocomposite. During the process, a spherical nano-sized HAp particle was precipitated following dissolution of micro-sized CaHPO₄・2H₂O. The PA66 monomers were subsequently adsorbed onto the generated HAp product. Some of the adsorbed PA66 monomers formed a bound polymer on HAp, and an increase in the adhesiveness of the PA66-HAp interface was observed as the polymerization progressed. During this process, the synthesis of a nanocomposite from a micro-sized raw material and creation of an autonomous strong interface between the matrix and filler was achieved. In addition, the shape of the resultant HAp was controllable and could be modified to needle shape by the addition of F⁻ and Mg²⁺ ions to the raw material. HAp could also be changed to plate shape via octa-calcium phosphate (OCP). Notably, during the synthesis, the filler shape of the nanocomposite could be controlled to 0D (particle), 1D (needle), and 2D (plate).     

用体硅微加工工艺实现的微纳电械系统

1　Ｉｎｔｒｏｄｕｃｔｉｏｎ　　ＭＥＭＳ (ＭｉｃｒｏＥｌｅｃｔｒｏＭｅｃｈａｎｉｃａｌＳｙｓｔｅｍ )ｂａｓｅｄｏｎｓｅｍｉｃｏｎｄｕｃｔｏｒｍｉｃｒｏｆａｂｒｉｃａｔｉｏｎｐｌａｙｓｉｍ ｐｏｒｔａｎｔｒｏｌｅｓｆｏｒｅｘａｍｐｌｅｉｎｔｈｅ ｐｅｒｉｐｈｅｒｙｏｆＩＴｓｙｓｔｅｍｓ.ＮＥＭＳ (ＮａｎｏＥｌｅｃｔｒｏＭｅｃｈａｎｉｃａｌＳｙｓ ｔｅｍ)ｃｏｎｔａｉｎｓｎａｎｏ＿ｓｃａｌｅｓｔｒｕｃｔｕｒｅｓ.Ｓｏｐｈｉｓｔｉｃａｔｅｄａｎｄｈｉｇｈｐｅｒｆｏｒｍａｎｃｅｓｙｓｔｅｍｓｂａｓｅｄｏｎｔｈ…     

Preparation of Pt-loaded TiO2 nanofibers by electrospinning and their application for WGS reactions

Preparation of Pt-loaded TiO₂ nanofibers and their catalytic performance for water gas shift (WGS) reactions have been explained in this work. The Pt-loaded TiO₂ nanofibers were obtained by electrospinning poly-ethylene oxide (PEO) aqueous solutions containing Ti(OH)_n slurry and Pt nanoparticles at room temperature, followed by calcination at 773 K for 4 h. The calcined nanofibers were rougher than the nanofibers of PEO/Ti(OH)_n/Pt due to the PEO degradation and oxidation of Ti(OH)_n to TiO₂. Diameters of the Pt-loaded TiO₂ nanofibers ranged between 200 and 900 nm. Catalytic activity of the Pt-loaded TiO₂ nanofibers for water gas shift (WGS) reactions was evaluated and it was observed that their activity was 5–7 times higher than that of a bulk catalyst. Such improvement is attributed to the larger surface area of the nanofiber catalyst compared to that of the bulk catalyst. To the best of our knowledge, this is the first demonstration of a synthesis of Pt-loaded TiO₂ nanofibers from a Ti(OH)_n nanoparticle slurry using electrospinning and its application to WGS reactions.     

A new approach to species determination for yeast strains: DNA microarray-based comparative genomic hybridization using a yeast DNA microarray with 6000 genes

DNA-DNA hybridization is known as the superior method in the elucidation of relationships between closely related taxa, such as species and strain. For species determination we propose a new DNA-DNA hybridization method: the DNA microarray-based comparative genomic hybridization (CGH) method, using a yeast DNA microarray with approximately 6000 genes. The genome from a yeast strain as a sample strain (Sample) was labelled with Cy3-dye and hybridized to a single DNA microarray, together with the Cy5-labelled genome of S. cerevisiae S288C as a reference strain (Reference). The log2 ratio values [log2[Cy3(Sample)/Cy5(Reference)]: Ratio] of signal intensities of all the gene spots were estimated and divided into the following groups: Ratio < or = -1; -1 < Ratio < 1; 1 < or = Ratio. The hybridization profiles of the genomes of type strains belonging to the genus Saccharomyces were significantly different from that of S. cerevisiae S288C. The Ratio-based grouping allowed us to discriminate between some species from S. cerevisiae more clearly. Furthermore, cluster analysis discriminated between closely related species and strains. Using this method, we were able to not only perform species determination but also to obtain information on alternation in gene copy number of such gene amplifications and deletions with single-gene resolution. These observations indicated that DNA microarray-based CGH is a powerful system for species determination and comparative genome analysis.     

Chromosome translocation induced by the insertion of the URA blaster into the major repeat sequence (MRS) in Candida albicans

Electrophoretic karyotype studies have shown that clinical isolates of Candida albicans have extensive chromosome length polymorphisms. Chromosome translocation is one of the causes of karyotypic variation. Chromosome translocation events have been shown to occur very frequently at or near the major repeat sequence (MRS) on chromosomes. The MRS consists of the repeated sequences RB2, RPS and HOK, and the repeated sequences are considered to be the template for recombination. To investigate which element of the MRS is important for chromosome translocation, we constructed three cassettes, each containing a URA blaster and sequences homologous to one of the repeats, for insertion into the MRS region on the chromosomes. The ura3 strain STN22u2, which shows a stable, standard karyotype, was transformed with each construct. Insertion events with each cassette occurred at almost all chromosomes. Insertion into the RB2 repeat, but not into the RPS repeat, was accompanied by chromosome translocation in some transformants: chromosome translocations between chromosomes R and 7 and chromosomes 1 and 7 were found, as well as deletions of 7A and 7C from chromosome 7. We conclude that the insertion at the RB2 region may initiate chromosome translocation in C. albicans.     

Transient thermal stresses in a composite hollow cylinder subjected to γ-ray heating

Transient temperature and thermal-stress distributions arising in an infinite long composite hollow circular cylinder subjected to internal heat generation decaying exponentially along the wall thickness resulting from γ-ray radiation are analyzed, under the thermal conditions of cooling by convection on the inner surface and insulation on the outer surface. Numerical calculations of the transient temperature and thermal-stress distributions are carried out for the case of a composite cylinder of stainless steel and carbon steel. The influence of the absorption coefficient, the Biot number and the splicing radius on the results are considered.