Analysis of lightning surge propagation in wind farm

Wind power generation is expected to become more important in future distribution systems. Although several prospective reports such as IEC 61400‐24 and NREL SR‐500‐31115 indicate an insulation scheme and grounding design for lighting protection, there still seems to be too few investigations on the problems. This paper therefore discusses lightning surge analysis using a wind farm model with 2 or 10 ideal wind turbines. Changing parameters such as grounding resistance and lightning strike points, several cases were studied. As a result of the analysis using digital simulator ARENE, it is clear that the surge tends to propagate toward the end of a distribution line in a wind farm and there is the possibility of insulation accidents at the other wind turbines when lightning attacks a wind turbine. © 2007 Wiley Periodicals, Inc. Electr Eng Jpn, 162(2): 30– 38, 2008; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20364     

Conversion of methane to syngas in a solid oxide fuel cell with Ni-SDC anode and LSGM electrolyte

A solid oxide fuel cell constructed from Ni-SDC anode and LSGM electrolyte was applied to the partial oxidation of methane to syngas (CO+H₂) at 700-800 °C with the merits of co-generation of electricity and controllable O₂ supply. It was found that the co-generated syngas at H₂/CO ratio of 1.4-2.0 varied with applied current densities, CH₄ flow rates and operating temperatures. The cell voltage at 100 mA cm⁻² and 800 °C was 0.90 V, i.e. about 90 mW cm⁻² power density could be obtained. The cell operating at 50 mA cm⁻² for 24 h almost showed no degradation of the cell performance. The observed carbon deposition seemed mainly taking place by CH₄ cracking reaction.     

Radiation-induced polymerization of ethylene in pilot plant. III. Heavy-phase recycling process

Radiation-induced polymerization of ethylene using aqueous tert-butyl alcohol as medium was carried out in a large-scale pilot plant with a 50-liter central source-type reactor at a pressure of 105 to 395 kg/cm², temperature of 30° to 80°C, mean dose rate of 4.5 × 10⁴ to 1.9 × 10⁵ rads/hr, ethylene feed rate of 5.5 to 23.5 kg/hr, and medium feed rate of 21 to 102 l./hr. The space–time yield and molecular weight of the polymer were in the range of 4.7 to 16.8 g/l.-hr and 1.3 × 10⁴ to 8.9 × 10⁴, respectively. The space–time yield and molecular weight increased with mean residence time at 30°C, whereas at 80°C they became almost independent of the time. The space–time yield increased with pressure and dose rate, slightly decreased with temperature, and was maximum at ethylene molar fraction of 0.5. The polymer molecular weight increased with pressure and ethylene molar fraction, and decreased with dose rate and temperature. The total amount of deposited polymer on the reactor wall, source case wall, and scraping blades was usually less than 1 kg, which was negligibly small for the analysis of polymerization. Continuous discharge of the polymer slurry and production of fine-powder polyethylene were successfully carried out. In the central source-type reactor, a dose rate of 1.9 × 10⁵ rads/hr was obtained with a ⁶⁰Co source of ca. 12 kCi.     

Glass transition and mechanical properties of PLLA and PDLLA‐PGA copolymer blends

The change of the glass transition temperatures (T_g) in the blend of poly(L ‐lactic acid) (PLLA) and the copolymers of poly(D,L ‐lactic acid) and poly(glycolic acid) (PDLLA‐PGA) with different D,L ‐lactic acid and glycolic acid composition ratio (50 : 50, 65 : 35, and 75 : 25) was studied by DSC. Dynamic mechanical measurement and tensile testing were performed at various temperatures around T_g of the blend. In the blend of PLLA and PDLLA‐PGA50 (composition ratio of PDLLA and PGA 50 : 50), T_g decreased from that of PLLA (about 58°C) to that of PDLLA‐PGA50 (about 30°C). A single step decrease was observed in the DSC curve around T_g between the weight fraction of PLLA (W(PLLA)) 1.0 and 0.7 (about 52°C) but two‐step changes in the curve are observed between W(PLLA) = 0.6 and 0.3. The T_g change between that of PLLA and that of PDLLA‐PGA and the appearance of two T_gs suggest the existence of PLLA rich amorphous region and PDLLA‐PGA copolymer rich amorphous region in the blend. A single step decrease of E′ occurs at around T_g of the pure PLLA but the two‐step decrease was observed at W(PLLA) = 0.6 and 0.4, supporting the existence of the PLLA rich region and PDLLA‐PGA rich region. Tensile testing for various blends at elevated temperature showed that the extension without yielding occurred above T_g of the blend. Partial miscibility is suggested for PLLA and PDLLA‐PGA copolymer blends. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2164–2173, 2004     

Earthquake onset detection using spectro-ratio on multi-threshold time–frequency sub-band

Automatic onset detection and picking algorithm has been proposed by applying the spectro-ratio on time–frequency sub-band. The proposed algorithm does not need any parameter settings as it will work on data generated by either short or very broad band seismometers. Our algorithm is applied on local events from Cairo region recorded by three stations of the Egyptian National Seismic Network (ENSN). Maximum standard deviation is observed to be 0.113 s of the corresponding manual picks made by analysts.     

A simple method to derive minimal cut sets for a non-coherent fault tree

Minimal cut sets (or prime implicants: minimal combinations of basic event conditions leading to system failure) are important information for reliability/safety analysis and design. To obtain minimal cut sets for general non-coherent fault trees, including negative basic events or multi-valued basic events, a special procedure such as the consensus rule must be applied to the results obtained by logical operations for coherent fault trees, which will require more steps and time. This paper proposes a simple method for a non-coherent fault tree, whose top event is represented as an AND combination of monotonic sub-trees. A "monotonic" sub-tree means that it does not have both positive and negative representations for each basic event. It is proven that minimal cut sets can be obtained by a conventional method for coherent fault trees. An illustrative example of a simple event tree analysis shows the detail and characteristics of the proposed method.     

Fabrication of bilayered YSZ/SDC electrolyte film by electrophoretic deposition for reduced-temperature operating anode-supported SOFC

Bilayered Y₂O₃-stabilized ZrO₂ (YSZ)/Sm₂O₃-doped CeO₂ (SDC) electrolyte films were successfully fabricated on porous NiO–YSZ composite substrates by electrophoretic deposition (EPD) based on electrophoretic filtration followed by co-firing with the substrates. In EPD, positively charged YSZ and SDC powders were deposited directly on the substrates, layer by layer from ethanol-based suspensions. Delamination between YSZ and SDC films was avoided by reducing the SDC films’ thickness to ca. 1 μm. A single cell was constructed on the bilayered electrolyte films composed of ca. 4 μm-thick YSZ and ca. 1 μm-thick SDC films. As a cathode in the cell, La_0.6Sr_0.4Co_0.2Fe_0.8O_3−x (LSCF) was used. Maximum output power densities greater than 0.6 W cm⁻² were obtained at 700 °C for the bilayered YSZ/SDC electrolyte cells thus constructed.     

Switched capacitor circuit for 1/f noise generation using a power-law circuit

A simple switched capacitor (SC) circuit is given which realizes a one-dimensional discrete dynamical system X_n+1 = X_n + ux^z generating intermittent chaos with a 1/f-shaped power spectrum. an integrated circuit with a pair of logarithmic and antilogarithmic amplifiters can easily realize the power-law term x^z which plays a key role in generating l/fnoise. an inevitable small offset voltage ? in the SC circuit governs the cut-off frequency of 1/f noise, and when the dynamical system is modified by introducing an effective ?, the ‘indirect method’ enables us to get the precise power spectrum in the modified system.     

Music composition by interaction between human and computer

This paper aims at constructing a music composition system that composes music by the interaction between human and a computer. Even users without special musical knowledge can compose 16-bar musical works with one melody part and some backing parts using this system. The interactive Genetic Algorithm is introduced to music composition so that users’ feeling toward music is reflected in the composed music. One chromosome corresponds to 4-bar musical work information. Users participate in music composition by evaluating composed works after GA operators such as crossover, mutation, virus infection are applied to chromosomes based on the evaluation results. From the experimental results, it is found that the users’ evaluation values become high over the progress of generations. That is, the system can compose 16-bar musical works reflecting users’ feeling. Muneyuki Unehara: He received his M.S. in Engineering in 2002 from Institute of Science and Engineering, University of Tsukuba. Currently, he is a Ph.D. candidate of Graduate School of Systems and Information Engineering, University of Tsukuba. His research interests include the construction of intelligent systems by considering soft computing techniques and human interface. Takehisa Onisawa, Ph.D.: He received Dr.Eng. in Systems Science in 1986 from Tokyo Institute of Technology. Currently, he is a Professor in the Graduate School of Systems and Information Engineering, University of Tsukuba. His research interests include applications of soft computing techniques to human centered systems thinking. He is a member of IEEE and IFSA.     

Improvement of productivity of active horseradish peroxidase in Escherichia coli by coexpression of Dsb proteins

Coexpression of two classes of folding accessory proteins, molecular chaperones and foldases, can be expected to improve the productivity of soluble and active recombinant proteins. In this study, horseradish peroxidase (HRP), which has four disulfide bonds, was selected as a model enzyme and overexpressed in Escherichia coli. The effects of coexpression of a series of folding accessory proteins (DnaK, DnaJ, GrpE, GroEL/ES, trigger factor (TF), DsbA, DsbB, DsbC, DsbD, and thioredoxin (Trx)) on the productivity of active HRP in E. coli were examined. Active HRP was produced by very mild induction with 1 microM isopropyl-beta-D-thiogalactopyranoside (IPTG) at 37 degrees C, whereas the amount of active HRP produced by the induction with 1 mM IPTG was negligibly small. Active HRP production was increased significantly by coexpression of DsbA-DsbB (DsbAB) or DsbC-DsbD (DsbCD), while coexpression of molecular chaperones did not improve active HRP production. The growth of E. coli cells was inhibited significantly by the induction with 1 mM IPTG in a HRP single expression system. In contrast, when HRP was coexpressed with DsbCD, the growth inhibition of E. coli was not observed. Therefore, coexpression of Dsb proteins improves both the cell growth and the productivity of HRP.