Variations in fundamental frequency peak position in Japanese macaque (Macaca fuscata) coo calls.

Japanese macaques (Macaca fuscata) produce coo calls whose use in various contexts is correlated with differences in the relative temporal position of the peak value of a call's fundamental frequency (S. Green, 1975). Studies have produced conflicting results about both the location of the category boundary between smooth early high and smooth late high coo subtypes and macaques' perceptual sensitivity to variations in peak position. In this study, fundamental frequency peak positions were measured in 578 coos produced by 8 captive adult female Japanese macaques in order to test whether calls with peak positions close to either of 2 hypothesized boundaries occurred at low rates. Overall, such calls were found to occur at rates equal to or higher than predicted by chance. Peak position varied more consistently between animals than by behavioral context. The results may indicate that peak position in coos does not form 2 distinct categories. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Evaluation of Serum Volume Losses During Long-Term Storage

Aliquots of serum collected in a large case-control study of cervical cancer were stored at −70°C for up to 4 years during implementation of the study. When 500 μL serum aliquots were thawed in preparation for carotenoid and vitamin A assays, volumes were noticeably variable and fell below 500 μL in the majority of the samples. We were concerned about evaporation/sublimation during storage of the samples because loss of water would concentrate the analytes of interest. We evaluated the use of density and sodium ion concentration measurements to confirm its occurrence. We found that serum density was an unreliable indicator of extent of volume loss since the anticipated increases in density due to evaporation were of the same magnitude as inter-individual variation in serum density. In contrast, Na⁺ concentration is tightly regulated and would rise if water had been lost from the samples. In a representative sample of serum aliquots from the case-control study, 24 of 25 vials contained less than 500 μL of serum. The mean sodium ion concentration (138.1 ± 3.6 mmol/L) was within the normal range for human serum of 136–145 mmol/L, and no correlation was observed between serum volume and Na⁺ concentration. These results strongly suggest that the observed low volumes were not due to evaporative losses. Instead, the variably low volumes of serum aliquots were probably due to pipetting errors in the initial aliquotting resulting from the use of air-displacement pipettes.     

The effect of cooling rate on the impact performance and dynamic mechanical properties of rotationally molded metallocene catalyzed linear low density polyethylene

This article examines changes to the morphology of rotationally molded metallocene catalyzed linear low density polyethylene brought about by varying the cooling rate during processing. These changes in morphology lead to variations in the impact performance, which is reflected in the dynamic mechanical characteristics of the materials. Various analytical techniques are used in an attempt to explain the differences in impact behavior. Slow cooling is shown to result in high crystallinity, and in the formation of large spherulites, which in turn is detrimental to the impact performance of the material, particularly at low temperatures. The high crystallinity corresponds with a shift in the β transition of the material to a higher temperature, and is shown to result in a higher brittle–ductile transition. A case study was also carried out on samples from a finished part provided by an industrial molder, one section of which failed in a brittle manner when impact tested while the other failed in a ductile manner. Microscopy results showed that the brittle material had large spherulites at the inside surface, while the ductile material showed incipient degradation at this surface, which has previously been shown to be of benefit to impact strength in rotationally molded parts. Dynamic mechanical studies again showed a β transition at a higher temperature in the brittle samples. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1963–1971, 2006     

The Quasi-static Deformation, Failure, and Fracture Behavior of Titanium Alloy Gusset Plates Containing Bolt Holes

In this article, the influence of bolt holes, specifically their number and layout on strength, deformation, and final fracture behavior of titanium alloy gusset plates under the influence of an external load is presented and discussed. Several plates having differences in both the number and layout of the bolt holes were precision machined and then deformed under quasi-static loading. The specific influence of number of bolt holes and their layout on maximum load-carrying capability and even fracture load was determined. The conjoint influence of bolt number, bolt layout pattern, nature of loading, contribution from local stress concentration, and intrinsic microstructural effects in governing the macroscopic fracture mode and intrinsic microscopic mechanisms is presented and discussed.     

Anteil erneuerbarer Energien und klimarelevante CO2-Emissionen aus der thermischen Verwertung von Abfällen in Österreich

Since combustible wastes usually consist of biogenic (e.g. paper, wood, food waste) and fossil organic matter (plastics), their thermal recovery results in climate neutral and climate relevant CO₂ emissions. Moreover, the fraction of biogenic materials in the waste feed is relevant for the amount of renewable energy produced. The latter has to be reported and might be subsidized according to national laws (e.g. based on European directive 2009/28/EG). The present study represents the first comprehensive evaluation of the share of biogenic and fossil materials in the waste feed of waste-to-energy (WTE) plants on a national basis. The Balance Method, which is patented on a European level by TU Wien, was applied to 10 out of 13 Austrian WTE plants (around 2.3 Mio tons of waste corresponding to around 88 % of the overall waste feed in Austrian WTE plants). The method is based on the mathematical reconciliation of the material properties (e.g. mean chemical composition of biogenic and fossil materials) and routinely recorded operating data of WTE plants (e.g. flue gas volume, CO₂ and O₂-content in the dry flue gas, steam production). The results demonstrate large variations for the share of energy from biogenic sources in the different WTE plants, ranging from 35.7 ± 2.4 % to 61.2 ± 2.7 % (based on annual averages). Additionally, for several WTE plants large temporal variations can be observed based on monthly mean values. Thus, a plant-specific and continuous evaluation of the waste composition in WTE plants (which the Balance Method allows to do at reasonable efforts) can be recommended for a reliable reporting of the renewable share of energy or fossil CO₂ emissions from waste incineration. The energy input which stems from fossil and biogenic sources can be estimated to 11,450 ± 120 TJ and 10,730 ± 110 TJ, respectively for the year 2014 (for the 10 WTE plants). In total 1060 ± 24 kt fossil CO₂ emissions from the thermal recovery of waste in Austria’s WTE plants in 2014 could be determined (estimation for all 13 WTE plants).     

Structural Response of World Trade Center Buildings 1, 2 and 7 to Impact and Fire Damage

The National Institute of Standards and Technology (NIST) conducted an extensive investigation of the collapse of World Trade Center towers (WTC 1 and WTC 2) and the WTC 7 building. This paper describes the component, subsystem, and global analyses performed for the reconstruction of the structural response of WTC buildings 1, 2, and 7 to impact and fire damage. To illustrate the component and subsystem analyses, the approach taken for simulating the performance of concrete slabs and shear stud connectors in composite floors subject to fire conditions are presented, as well as steel floor framing connections for beams and girders. The development of the global models from the component and subsystem analyses is briefly described, including the sets of input data used to bound the probable conditions of impact and fire damage. The final analysis results that were used to develop the probable collapse hypotheses, and a comparison of the results against observed events, are presented for each building. A review of research activities focused on improving understanding of structural system response to multi-floor fires following the WTC disaster is also provided.