Ammonia production using iron nitride and water as hydrogen source under mild temperature and pressure

Ammonia generation was studied in the reaction between water and nitrogen-containing iron at 323 K and atmospheric pressure. Similar to metallic Fe, the interstitial compound Fe₃N reduced water through Fe oxidation to produce hydrogen gas, while the N combined with atomic hydrogen to produce ammonia as a byproduct. The addition of carbon dioxide to this system accelerated the reaction with concomitant consumption of carbon dioxide. The promoted ammonia production upon addition of carbon dioxide can be attributed to the generation of atomic hydrogen from the redox reaction of carbonic acid and Fe, as well as removal of used Fe from the reaction system through the formation of a soluble carbonato complex. When carbonate was added to the reaction system, the production rates of ammonia and hydrogen increased further. The results here confirmed that ammonia can be synthesized from iron nitride under mild conditions by utilizing carbon dioxide.     

Contribution of metal vapor mass at periphery part of pulsed arc to electromagnetic force in weld pool

The arc welding has been used in various welding methods because it is inexpensive and high in strength after welding. However, it is a problem that accidents such as collapse of the bridge occur because of the welding defects. The welding of low cost and high productivity is required without the welding defects. The pulsed TIG welding is inexpensive and capable of high‐quality welding. The electromagnetic force contributing to penetration changes because the transient response of arc temperature and iron vapor generated from anode occurs. However, the analysis of pulsed TIG welding with metal vapor has been elucidated only metal vapor concentration near anode with transient phenomenon and heat flux. Thus, the theoretical elucidation of penetration depth with control factor has not been researched. In this paper, the contribution of metal vapor mass at the periphery part of pulsed arc to the electromagnetic force in the weld pool is elucidated. As a result, the iron vapor mass at periphery part decreased with increasing the frequency. The iron vapor was stagnated at axial center within one cycle. The electromagnetic force to the penetration depth direction in weld pool increased at axial center. Therefore, the metal vapor mass at periphery part plays an important role for the electromagnetic force increment at axial center.     

Liquid Marble Patchwork on Super-Repellent Surface

Liquid marble (LM) is a droplet that is wrapped by hydrophobic solid particles, which behave as a non-wetting soft solid. Based on these properties, LM can be applied in fluidics and soft device applications. A wide variety of functional particles have been synthesized to form functional LMs. However, the formation of multifunctional LMs by integrating several types of functional particles is challenging. Here, a general strategy for the flexible patterning of functional particles on droplet surfaces in a patchwork-like design is reported. It is shown that LMs can switch their macroscopic behavior between a stable and active state on super-repellent surfaces in situ by jamming/unjamming the surface particles. Active LMs hydrostatically coalesce to form a self-sorted particle pattern on the droplet surface. With the support of LM handling robotics, on-demand cyclic activation–manipulation–coalescence–stabilization protocols by LMs with different sizes and particle types result in the reliable design of multi-faced LMs. Based on this concept, a single bi-functional LM is designed from two mono-functional LMs as an advanced droplet carrier.     

Fast microwave detection system for coherent synchrotron radiation study at KEK: Accelerator test facility

A fast room temperature microwave detection system based on the Schottky Barrier-diode detector was created at the KEK ATF (Accelerator Test Facility). It was tested using Coherent Synchrotron Radiation (CSR) generated by the 1.28 GeV electron beam in the damping ring. The speed performance of the detection system was checked by observing the CSR from a multi-bunch (2.8 ns bunch separation time) beam. The theoretical estimations of CSR power yield from an edge of bending magnet as well as new injection tuning method are presented. A very high sensitivity of CSR power yield to the longitudinal electron distribution in a bunch is discussed.     

Operation of superconducting fault current limiter using vacuum interrupter driven by electromagnetic repulsion force for commutating switch

Using conventional high‐temperature superconducting wire, a model superconducting fault current limiter (SFCL) is made and tested. Solenoid coil using Bi2223 silver sheath wire is so made that inductance is as small as possible and a vacuum interrupter is connected in series to it. A conventional reactor coil is connected in parallel. When the fault current flows in this equipment, superconducting wire is quenched and current is transferred into the parallel coil because of voltage drop of superconducting wire. This large current in parallel coil actuates magnetic repulsion mechanism of vacuum interrupter. Due to opening of vacuum interrupter, the current in superconducting wire is broken. By using this equipment, current flow time in superconducting wire can be easily minimized. On the other hand, the fault current is also easily limited by large reactance of parallel coil. © 2008 Wiley Periodicals, Inc. Electr Eng Jpn, 164(1): 52–61, 2008; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20315     

Phase diagrams calculated for Fe-rich Fe-Si-Co and Fe-Si-Al ordering alloy systems

Theoretical analysis based on the calculation of phase diagrams was employed for Fe-Si-Co and Fe-Si-Al ordering systems to clarify the necessity for the occurrence of phase separation in Fe-base ternary ordering systems. The free energy of Fe-base ternary ordering alloys where B2 and D0₃ ordered structures are formed is evaluated statistically using a pairwise interaction approximation up to second nearest neighbours, taking into account not only the atomic interaction but also the magnetic interaction, based on the Bragg-Williams-Gorsky model. The calculated phase diagrams are consistent with the experimentally obtained ones. The phase diagram calculation in this work is useful to predict the equilibrium states of the ternary ordering systems. The phase separation in ordering alloys is caused by the contribution of excess free energies due to ordering. The influences of ferromagnetism on the two-phase regions are also demonstrated.     

Enhancement by ganglioside GT1b of annexin I phosphorylation in bovine mammary gland in the presence of phosphatidylserine and Ca2+

Ganglioside GT1b and, to a lesser extent, GD3, enhanced phosphorylation of a 36 kDa protein (the substrate of protein kinase C) in the particulate fraction from bovine mammary gland. Sialic acids, asialogangliosides, and GM3 were without effect, and GD1a conversely inhibited phosphorylation of the 36 kDa protein. The enhanced phosphorylation by GT1b required the simultaneous presence of phosphatidylserine (PS) and Ca²⁺. The 36 kDa protein reacted with anti-annexin I in Western blot analysis. Addition of purified annexin I to the reaction mixture containing the particulate fraction increased the extent of phosphorylated 36 kDa protein, and the phosphorylation was further enhanced by GT1b. The enhanced phosphorylation of annexin I by GT1b was also dependent on PS and Ca²⁺. When annexin I was phosphorylated by purified protein kinase C, GT1b inhibited the annexin I phosphorylation. Addition of epidermal growth factor or insulin to the particulate fraction had little effect on the enhancement. These results suggest that an enzyme or enzymes other than protein kinase C, epidermal growth factor receptor kinase, or insulin receptor kinase is responsible for the GT1b- and GD3-enhanced phosphorylation of annexin I in the presence of PS and Ca²⁺.