Fabrication of lotus-type porous carbon steel by the continuous zone melting method and its mechanical properties

A lotus-type porous carbon steel with cylindrical pores was fabricated by the continuous zone melting method in a pressurized mixture of hydrogen and helium gases. The porosity increases with increasing partial pressure of the hydrogen gas, while the pore diameter remains almost constant, independent of the pressure. The ultimate tensile strength of the specimen with cylindrical pores parallel to the tensile direction is lower than the estimated value, assuming that the strength is decreased in proportion to the decrease of the cross-sectional area of the specimen, while the yield strength is higher than the estimated value. The compressive yield strength is also higher than the estimated value. The increase in yield strength is considered to be due to precipitation strengthening. The tensile strength is increased by quenching and tempering, while the elongation decreases. Such mechanical properties are discussed in terms of the microstructural analysis.     

Simulation of Strength Distribution in Ground Ceramics by Incorporating Residual Stress Effect

Strength of ground ceramics may be affected by residual stress as well as surface flaws induced by grinding. Strength prediction for ground ceramics is convenient for mechanical design of ceramic components. In this article, a numerical procedure based on fracture mechanics was proposed to estimate strength distribution of ground ceramics by considering grinding-induced residual stress. Bending strength and residual stress of ground ceramics were measured for three grinding-conditions. By comparison of simulated results with experimental ones, it was revealed that strength characteristics in experiments were well simulated by using the proposed procedure.     

A 322 MHz random-cycle embedded DRAM with high-accuracy sensing and tuning

A 16 Mb embedded DRAM macro in a fully CMOS logic compatible 90 nm process with a low noise core architecture and a high-accuracy post-fabrication tuning scheme has been developed. Based on the proposed techniques, 61% improvement of the sensing accuracy is realized. Even with the smallest 5 fF/cell capacitance, a 322 MHz random-cycle access while 32 ms data retention time which contributes to save the data retention power down to 60 /spl mu/W are achieved.     

Passivation effects of deuterium exposure on boron-doped CVD homoepitaxial diamond

The deuterium (hydrogen) passivation effect on acceptors in boron-doped CVD homoepitaxial diamond was studied by electrical (Hall-effect) and secondary ion mass spectroscopy (SIMS) measurements. Deuterium was incorporated into the samples using microwave (MW) deuterium plasma at 673 K for 2–24 h. We observed the progress of acceptor passivation with p-type conduction, which finally resulted in a highly resistive state.     

Feedback control of decoupled bending and torsional vibrations of flexible beams

In this article, we consider a flexible beam with a rigid body, of which the bending vibration and the torsional vibration are decoupled. Therefore we need two control motors to suppress the vibrations. Each set of dynamic equations is treated in the form of an appropriate Hilbert space. A stabilizing feedback control law of each rotation motor will be established on the basis of modal analysis. A set of experiments has been carried out, and the results demonstrate the effectiveness of the dynamic model and the proposed control law. © 1994 John Wiley & Sons, Inc.     

High-efficiency finishing process for metal mold by large-area electron beam irradiation

A new finishing process for metal molds by large-area electron beam (EB) irradiation is proposed in this study. In the large-area EB irradiation equipment used here, an EB with high-energy density is irradiated without focusing the beam, and so the EB with a maximum diameter of 60 mm can be used for melting or evaporating metal surface instantly. Experimental results show that the surface roughness decreases from 6 μmRz to less than 1 μmRz in just a few minutes under proper machining conditions. The corrosion resistance of metal mold surface also could be greatly improved by large-area EB irradiation. Furthermore, the surface roughness of tilting surface close to 90° could be well improved. Therefore, large-area EB irradiation method has a possibility to become a high-efficiency finishing process for metal molds.     

Effect of rapid sample cooling on efficiency of multiple impurity-atom doping

Shallow and efficient doping of wide band-gap semiconductors has remained one of yet unresolved problems to date. A possible solution to this problem is doping with complexes of a few impurity atoms at a quasi-equilibrium state, which is introduced by controlled cooling of a sample after doping. In this work, (1) we first define a global and quasi-equilibria of our interest based on a simple thermodynamic model for a doped crystal, and then (2) we discuss how the cooling rate affects the probability of impurity-complex formation at a quasi-equilibrium as defined. Our main message is that one should design impurity complexes as small in size as possible which have as large a binding energy as possible. This is a required condition for complex designs when it is difficult to tune the cooling rate.     

Dendritic remodelling of retinal ganglion cells during development of the rat

Investigation of the morphology of ganglion cells in the cat retina has shown that a remarkable reduction in the number of dendritic spines and branches occurs during development of the alpha and beta cell classes. To learn whether dendritic remodelling represents a generalized mechanism of mammalian retinal ganglion cell development, we have examined the morphology of ganglion cells in the retina of the developing rat. The present study has concentrated on type II cells, which retain a great number of dendritic spines and branches in the adult and comprise a large proportion of the population of rat retinal ganglion cells. To reveal fine dendritic and axonal processes, Lucifer yellow was injected intracellularly in living retinae maintained in vitro. Size and complexity of the dendritic trees were found to increase rapidly during an initial stage of development lasting from late fetal life until approximately postnatal day 12 (P12). Dendrites and axons of immature ganglion cells expressed several transient morphological features comprising an excessive number of dendritic branches and spine-like processes, and short, delicate axonal sidebranches. The following developmental stage was characterized by a remarkable decrease in the morphological complexity of retinal ganglion cells and a slowed growth of their dendritic fields. The number of dendritic branches and spines of types I and II retinal ganglion cells declined after P12 to reach a mature level by the end of the first postnatal month. Thus, even cells that retain a highly complex dendritic tree into the adult state undergo extensive remodelling. These results suggest that regressive modifications at the level of the dendritic field constitute a generalized mechanism of maturation in mammalian retinal ganglion cells.