Effects of Winding Attachment Positions on Output Characteristics of Flux‐Modulating Synchronous Machines

The flux‐modulating synchronous machine (FMSM) is a new type of multipole SM with nonoverlapping concentrated armature and field windings on the stator. This paper compares the output characteristics of two FMSMs through finite element analysis (FEA) and experiments. In both of the FMSMs, the attachment positions of the armature and field windings are swapped. To determine the reason for the discrepancies in their output characteristics, unsaturated inductances were calculated using a d‐‐q equivalent circuit. In addition, the calculated results of the inductances were confirmed through a visualization of the leakage fluxes using FEA. The results of the study show that the synchronous inductance can be reduced by attaching the armature winding to the air‐gap side of the stator teeth and that the reduction leads to an increase in output power.     

Correlation between motion of source bender element and feedback signal induced by self-monitoring

Since the introduction of bender element tests to soil testing, the reliability of the estimated travel time has been the most serious problem. The author has previously shown a potential solution whereby removing the response of the bender element subsystem from the whole response could dramatically improve the accuracy of the travel time estimation. In order to lay the foundation for estimating the response of the bender element subsystem, this paper examines the correlation between the displacements of the element and the induced feedback signals by employing a self-monitoring element. The response of the self-monitoring element is modeled as a transfer function involving two internal transfer functions that relate the input signals to the displacements and the displacements to the feedback signals, respectively. Using a laser displacement sensor, the displacements are directly measured through the entire surface and reveal the three-dimensional bending motion of the element oscillating in both longitudinal and width directions. The feedback signals are similar to, but inconsistent with, the tip displacements, and an attempt is made to correct the feedback signals. Finally, a conclusion is given on the potential for estimating the response of the bender element subsystem using the self-monitoring element.     

Enhancement of nutraceutical properties of licorice callus cultures using sample pre-treatment strategy

Licorice is an herbal plant in the Leguminosae family, and its roots and rhizomes are used as sweeteners in food and confectionery products. Moreover, it has a distinct inflammatory activity. In the present study, a sample pre-treatment method to induce the deglycosylation of active metabolites in callus cultures of Glycyrrhiza inflata (GI) and Glycyrrhiza glabra (GG) was developed. The results of the method evaluation showed the biotransformation of ononin to formononetin, a rare flavonoid found in trace amounts in licorice. The magnitude of enhancement was 3- and 19-fold in the GI and GG samples, respectively. Moreover, the anti-inflammatory activity assay showed that the potency of the sample pre-treatment group was higher than that of the untreated group because it exerted an enhanced suppression of cyclo-oxygenase 2 (COX-2), interleukin-6 (IL-6) and inducible nitric oxide synthase (iNOS) gene expression. This is the first report on the anti-inflammatory activity of licorice callus, which has the potential to be utilised as a functional food for health promotion. These findings support the idea of using sample preparation to impart nutraceutical properties to plant products.     

Dielectric relaxation of vegetable-based polyurethane

Vegetable-based polyurethane (PU) was prepared in the thin film form by spin coating. This polymer is synthesised from castor oil, which can be extracted from the seeds of a native plant in Brazil called mamona. This polymer is biocompatible and is being used as material for artificial bone. The PU was characterised by dielectric spectroscopy in a wide range of frequency (10^–5 Hz to 10⁵ Hz) and by thermally stimulated discharge current (TSDC) measurements. The glass transition temperature (T _g = 39°C) was determined and using the initial rise method the activation energy was found to be 1.58 eV.     

High-gain hybrid amplifier consisting of cascaded fluoride-based TDFA and silica-based EDFA in 1458-1540 nm wavelength region

A hybrid optical fibre amplifier is described that consists of a fluoride-based thulium-doped fibre amplifier and a silica-based erbium-doped fibre amplifier connected in a cascade. The amplifier has a gain of more than 25 dB and a noise figure of less than 9 dB over a wide wavelength region of 1458-1540 nm.     

Correlation between serum levels of alanine aminotransferase and ferritin in male blood donors with antibody to hepatitis C virus

Chronic hepatitis C has been demonstrated to be associated with hepatic iron overload, and the hypothesis that the disease activity of hepatitis C is associated with iron cytotoxicity was tested in male volunteer blood donors. Sera with either antibody to hepatitis C virus or hepatitis B surface antigen were selected for determination of ferritin concentration and alanine aminotransferase activity. A correlation between serum ferritin concentration (Y; microgram/l) and alanine aminotransferase activity (X; IU/l) was found in donors with antibody to hepatitis C (log Y = 0.65 x log X + 0.98, r = 0.53, and P < 0.01). The correlation was lower in donors with hepatitis B surface antigen (r = 0.37; P < 0.01). Hepatitis C virus infection probably induces time-dependent iron accumulation associated with the progression of disease activity, while hepatitis B virus infection results in a variety of iron loads with different clinical features. The high disease activity related to hyperferritinemia suggests the presence of iron-induced liver damage in donors with hepatitis C.     

Unperturbed dimension of poly(4-acetoxystyrene) measured in good and theta solvents

In order to obtain the additional data concerning the unperturbed dimension of poly-4-substituted styrene, light scattering measurements are performed on the twenty-two fractions with molecular weight of (0.91–352)·10⁴ of poly(4-acetoxystyrene) in dioxan at 25°C, from which the molecular weight obtained was found easily to be evaluated with the gel permeation chromatography using THF. Phase separation experiments for this polymer indicate that the theta state is attained in isopropyl acetate at 19.7°C and butyl acetate at 26.8°C. By making viscosity measurements at that state, the value of K_Θ is directly evaluated as 5.4·10^?4 dl g^?1. The limiting viscosity number is also obtained in good solvents, THF and dioxan, at 25°C and constants of the Mark-Houwink-Sakurada equation in each solvent are determined. Further, approximately the same K_Θ as above is obtained from these data with the Stockmayer-Fixman plot. The calculated value of steric factor, 2.37, on this polymer may be plausible, compared with those of polyvinylaromatic derivatives.     

Novel T-rail electrodes for substrate removed low-voltage high-speed GaAs/AlGaAs electrooptic modulators

A novel traveling-wave electrode utilizing capacitively loaded T-rail elements was developed for low-voltage high-speed substrate-removed GaAs/AlGaAs electrooptic modulators. Electrodes with varying dimensions were fabricated and characterized. Electrode phase velocity, characteristic impedance, loss coefficient, and capacitive loading were extracted from the measured s-parameters up to 40 GHz. Electrode was also simulated using a finite-element solver. The measured and calculated electrode capacitance values were found to be in excellent agreement, showing that the electrode can be precisely designed. Approaches were outlined to provide a group velocity-matched very high-speed modulator electrode suitable for a low drive-voltage substrate-removed GaAs/AlGaAs electro-optic modulator     

Strengthening of Preloaded RC Beams Using Hybrid Carbon Sheets

Reinforced concrete (RC) beams subject to service loads of 40 or 60% of steel yielding were strengthened using hybrid continuous carbon fiber sheets. The hybrid systems were made of high-strength and high-modulus carbon sheets, and compared with systems using only high-strength carbon. It was found that the use of high-modulus carbon sheets in hybrid systems could increase the yielding load, the flexural stiffness, the postyielding ductility, and reduce the crack opening in concrete. The slope changes on load-deflection curves at steel yielding are not noticeable in hybrid systems. The tensile strains developed in hybrid sheets after the fracture of high-modulus carbon are higher in magnitude and distributed in a larger area, leading to an ultimate carbon fracture with concrete crushing. These unique features are attributed to the high stiffness and low ultimate tensile strain of the high-modulus carbon fibers which stiffen the structures, avoid or delay the fiber-reinforced polymer debonding, and facilitate the deformability during their subsequent breakdown.