A highly transparent and thermally stable copolymer of 1‐adamantyl methacrylate and styrene

Thermal and optical properties of copolymers of 1‐adamantyl methacrylate (AdMA) and styrene (St) prepared by free radical polymerization in the bulk are investigated. The copolymer forms an azeotrope when the composition is AdMA/St = 55/45 mol%. The glass transition temperature and decomposition temperature of the azeotropic copolymer are 170 and ca 340 °C, respectively. The refractive index increases nonlinearly with St content from 1.522 to 1.591. The light scattering loss at 633 nm is 28.1 dB km^?1, which is less than half of that of polystyrene. The total optical loss including molecular vibrational absorption, which is evaluated using a copolymer‐based optical fiber, is 292–645 dB km^?1 at 500–700 nm. These values correspond to transmittances of 86–93% for a 1 m optical path length. © 2014 Society of Chemical Industry     

Heparin affinity high-performance liquid chromatography as an alternative to bioassay of CS23 mutein of recombinant human basic fibroblast growth factor

We investigated whether a chemical assay by high-performance liquid chromatography (HPLC) as an alternative to the complicated and time-consuming bioassay for CS23 mutein of recombinant human basic fibroblast growth factor (rhbFGF-CS23) using the fetal bovine heart endothelial cell line ATCC CRL 1395. Physically, chemically or enzymatically denatured rhbFGF-CS23 was subjected to heparin affinity (HA)-HPLC and the bioassay. Good agreement was observed between the results obtained by these two methods. Moreover, HA-HPLC gave much more reproducible results (RSD = 1.9%, n = 6) than the bioassay (RSD = 7.4%, n = 18). HA-HPLC is therefore a simple, accurate and reproducible alternative to the bioassay for quality control and stability studies for rhbFGF-CS23 preparations. HA-HPLC is also considered to be applicable to assays for FGFs which have heparin affinity and biological activity similar to those of the CS23 mutein.     

Strength and ductility under dynamic loading in fine- grained IN905XL aluminum alloy

Three IN905XL aluminum alloys with fine grain (1 μm), intermediate grain (3 μm), and coarse grain (5 μm) have been developed by a combination of mechanical alloying (MA) and conventional extrusion in order to investigate their mechanical properties at dynamic strain rates of 1 × 10³ and 2 × 10³ s⁻¹ and a quasi-static strain rate of 10^-3 s⁻¹. Flow stresses are found to increase with decreasing grain size for all the strain rates tested. Negative strain-rate sensitivity of flow stress is observed up to 1 × 10³ s⁻¹ in both intermediate- and coarse-grained IN905XL. At the highest strain rate of 2 × 10³ s⁻¹ however, all samples showed a positive strain-rate sensitivity of strength. Total elongation at high strain rates is generally larger than that at low strain rates. Total elongation also decreases with grain size for all the strain rates. This decrease in elongation results from an initiation of microcracks at interfaces between the matrix and particles finely dispersed near grain boundary regions, introduced during MA processing; then, this initiation leads elongation of alloys to small limited values. Formerly with the Department of Mechanical Systems Engineering, University of Osaka Prefecture. This article is based on a presentation made in the symposium “Dynamic Behavior of Materials,” presented at the 1994 Fall Meeting of TMS/ASM in Rosemont, Illinois, October 3-5, 1994, under the auspices of the TMS-SMD Mechanical Metallurgy Committee and the ASM-MSD Flow and Fracture Committee.     

Hydroliquefaction of low-sulfur coals using iron carbonyl complexes—Sulfur as catalysts

Hydroliquefaction of low-sulfur Australian coals (Wandoan and Yallourn) was studied using iron carbonyl complexes as catalyst. The addition of Fe(CO)₅ (2.8 wt% Fe of coal) increased coal conversion from 48.6 to 85.2% for Wandoan coal, and from 36.7 to 69.7% for Yallourn coal in 1-methylnaphthalene at 425°C under an initial hydrogen pressure of 50 kg cm^?2. When molecular sulfur was added to iron carbonyls (Fe(CO)₅, Fe₂(CO)₉ and Fe₃(CO)₁₂), higher coal converions ( > 92%) and higher oil yields (>46%) were obtained, along with an increase in the amount of hydrogen transferred to coal from the gas phase (0.2 to 2.8%, d.a.f. coal basis). In the liquefaction studies using a hydrogen donor solvent, tetralin, Fe(CO)₅S catalyst increased the amount of hydrogen absorbed from the gaseous phase and decreased the amount of naphthalene dehydrogenated from tetralin. The direct hydrogen transfer reaction from molecular hydrogen to coal fragment radicals seems to be a major reaction pathway. Organic sulfur compounds, dimethyldisulfide and benzothiophene, and inorganic FeS₂ and NiS were found to be good sulfur sources to Fe(CO)₅. From X-ray diffraction analyses of liquefaction residues, it is concluded that Fe(CO)₅ was converted into pyrrhotite (Fe_1?xS) when sulfur was present, but into Fe₃O₄ in the absence of sulfur.     

The origination and optimization of Si/SiO/sub 2/ interface roughness and its effect on CMOS performance

As CMOS device dimensions scale down to 100 nm and beyond, the interface roughness between Si and SiO/sub 2/ has become critical to device performance and reliability. Si/SiO/sub 2/ interface roughness degrades channel mobility decreasing drive currents. The authors have used atomic force microscopy to study surface roughness in the processing of 0.16 /spl mu/m CMOS integrated circuits. All of the process steps that could potentially affect the interface roughness have been studied. The results show that oxidation is the major contributor to the interface roughness. The rms roughness is found to be linearly dependent on oxide thickness. Transistors with Si/SiO/sub 2/ interface rms roughness that has been reduced from 1.6 to 1.1 /spl Aring/ by reducing oxide thicknesses show improved device drive currents. This technique for interfacial smoothing and device performance improvement has the advantage of being easily implemented in today's technology.     

Quantitative trait loci affecting 4-nitroquinoline 1-oxide-induced tongue carcinogenesis in the rat

The incidence of tongue carcinomas (TCs) induced by oral administration of 4-nitroquinoline 1-oxide in rats is strain dependent. The inbred Dark-Agouti (DA) strain showed a much higher susceptibility to large mass-forming infiltrative TCs than did the Wistar-Furth (WF) strain. Our previous study (M. Kitano et al, Jpn. J. Cancer Res., 87: 1097-1101, 1996) on crosses between these two strains postulated a dominant susceptibility gene in DA and a dominant resistance gene in WF rats. The present study mapped these loci by analyzing the backcrosses to each parent with simple sequence repeat polymorphisms. Five quantitative parameters were analyzed: (a) the number of TCs > 5 mm in diameter; (b) the total number of TCs per rat; (c) the diameter of the largest TCs (DTCmax values); (d) the number of non-TC cancers per rat; and (e) and the number of cancers of any site per rat. All of these parameters were closely correlated (P < 0.0001). DA rats had a semidominant gene (Stc1) favoring the development of 4-nitroquinoline 1-oxide-induced cancers on chromosome 19, closely linked to D19Mit9. Peak linkage was observed 4 cM distal from D19Mit9, with a logarithm of the odds (lod) score of 5.72 for the number of large TCs and 6.08 for the DTCmax. On the other hand, WF rats had a semidominant gene (Rtc1) mapped between D1Mit1 and D1Mit3, approximately 20 cM from D1Mit1, with a peak lod score of 3.30 for both the number of large TCs and the DTCmax. The main effect of Rtc1 seemed to be to reduce the size of the TCs. The action of these genes was dose dependent and cooperative. The final incidence of TC in DA, WF, F1, and backcross rats seemed to be explained by combinations of genotype at these two loci. Possible candidate genes for Stc1 and Rtc1 are discussed.     

Development of a Cyclogyro-Based Flying Robot With Variable Attack Angle Mechanisms

This paper presents an experimental study on the development of a cyclogyro-based flying robot with a new variable angle of attack mechanism. A cyclogyro is a flying machine supported in the air by power-driven rotors that rotate about a horizontal axis, like the paddle-wheels of a steamboat. Machines of this type have been designed by some companies but there has been no record of any successful flights. Our design starts with a new variable angle of attack mechanism with an eccentric (rotational) point in addition to a rotational point connecting to a motor. The main feature of the mechanism with the eccentric rotational point is the ability to change attack of angles in accordance with the wing positions (as determined by the rotational angles of the cyclogyro) without actuators. The design parameters (wing span, the number of wings, and eccentric distance) of the flying robot are determined through a series of experiments. Experimental results show that the cyclogyro-based flying robot with the new variable angle of attack mechanism is capable of generating sufficient lift force for flying.     

A unified analysis of resonant converters

The general method of analysis for resonant power converters is presented. This analytical method generalizes the idea of state-space-averaging technique to overcome the limitations of the conventional state-space-averaging method. As the result, the characteristics of resonant power converters are clarified so that transfer functions and stability conditions are revealed. In addition, a computer program of analysis based on the proposed method is developed. The program can be applied to various resonant power converters, even when they have parasitic losses and higher-order resonant circuits     

Precise rendering method for exact anti-aliasing and highlighting

This paper introduces the Precise Rendering Method, which generates accurately anti-aliased and highlighted images from tessellated polygons. The Precise Rendering Method first solves the aliasing problems of hidden surface removal by using the Cross Scanline Algorithm. This algorithm can exactly calculate polygon areas projected onto each pixel by using horizontal and vertical scanlines. Aliasing artifacts in shading are then prevented by the Reflection Intergration Method, which analytically integrates the intensity of reflection in the solid angle defined by surface normals at vertices of the projected area. Several synthesized images are created to show the efficiency of the Precise Rendering Method.