Triglyceride analysis by combined argentation/nonaqueous reversed phase high performance liquid chromatography

Full analysis of triglycerides of natural fats and oils has been investigated by the combination of argentation high performance liquid chromatography (HPLC) with nonaqueous reversed phase (NARP) HPLC. An infrared detector was used in argentation HPLC, because it indicated molar responsibility to all triglycerides. After peak trapping with argentation HPLC, each triglyceride fraction was analyzed with NARP chromatography using the glyceride-selective post-column reactor detector. The results of the analyses of triglycerides of palm oil and cocoa butter by the proposed method agreed well with those reported earlier.     

Microwave switch: LAMPS (light-activated microwave photoconductive switch)

A new microwave switch, the light-activated microwave photoconductive switch consisting of a heterostructure photoconductive switch (HPCS) with a flip-chip bonded vertical-cavity surface-emitting laser is reported. An insertion loss of 0.17 dB at a laser power of 15 mW and an isolation of 25 dB were obtained at 1 GHz. Excellent linearity was obtained with second and third order intercepts measured at 960 MHz of SOI=115 dBm and TOI=65 dBm at 960 MHz, respectively.     

Dynamic mechanical properties of photopolymerizable poly(vinyl alcohol)–acrylate monomer blends

Dynamic mechanical properties of photopolymerizable poly(vinyl alcohol) (PVA)–monoacrylate blends were investigated by measuring dynamic shear modulus G′ and loss tangent, tan δ. The dynamic mechanical properties of the blends before being exposed to UV irradiation were governed by the weight percent of the monomers which act as plasticizers. On the other hand, the UV-irradiated blends seemed to be typical two-phase materials since they revealed two tan δ maxima whose positions were independent of the monomer content. Those two maxima were assigned to PVA and photopolymerized acrylates with reference to the dynamic mechanical data of PVA and a PVA-polyacrylamide polyblend. Those dynamic mechanical data suggested that insolubilization of the blend type photopolymers should be caused by a decrease in solubility due to graft polymerization of acrylate monomers onto PVA.     

Changes in Aging Behavior and Defect Structure of Yttria-Fully-Stabilized ZrO2 with Sc2O3 Doping

Methods of suppressing decreased conductivity in 8 mol% Y₂O₃-stabilized–92 mol% ZrO₂ (8YSZ) with aging were investigated. Different amounts of Sc₂O₃ were doped into 8YSZ. The electrochemical properties of Sc₂O₃-doped 8YSZ were measured, and the microstructural and local structural changes were characterized. The present results indicate that an appropriate amount of Sc₂O₃ doping, 3 or 4 mol%, effectively suppresses decreased conductivity with aging in 8YSZ.     

Design of new catalysts for ecological high-quality transportation fuels by combinatorial computational chemistry and tight-binding quantum chemical molecular dynamics approaches

Recently, we introduced a concept of combinatorial chemistry to computational chemistry and proposed a new method called “combinatorial computational chemistry”, which enables us to perform a theoretical high-throughput screening of catalysts. In the present paper, we reviewed our recent application of our combinatorial computational chemistry approach to the design of new catalysts for high-quality transportation fuels. By using our combinatorial computational chemistry techniques, we succeeded to predict new catalysts for methanol synthesis and Fischer–Tropsch synthesis. Moreover, we have succeeded in the development of chemical reaction dynamics simulator based on our original tight-binding quantum chemical molecular dynamics method. This program realizes more than 5000 times acceleration compared to the regular first-principles molecular dynamics method. Electronic- and atomic-level information on the catalytic reaction dynamics at reaction temperatures significantly contributes the catalyst design and development. Hence, we also summarized our recent applications of the above quantum chemical molecular dynamics method to the clarification of the methanol synthesis dynamics in this review.     

Effect of CNTs on Activation Volume and Mobile Dislocation Exhaustion Rate of CNTs/Al under Compression Loading

In this study, stress relaxation compression tests were performed to investigate the strain rate sensitivity, activation volume and mobile dislocations in carbon nanotubes/aluminum (CNTs/Al) composites. The results reveal that, with the addition of CNTs, the strain rate sensitivity of CNTs/Al increased. Meanwhile, a smaller V^* of CNTs/Al compared with pure Al was attributed mainly to the CNT-Al interfaces and partly to the increased forest dislocations cutting activities in grain interior, which was related to the tendency of short ranges order formation during plastic deformation. The incorporation of CNTs also improved the dislocation storage capability and reduced the dislocation velocity, leading to a lower mobile dislocation exhaustion rate.     

Synthesis of Dense Lead Titanate Ceramics with Submicrometer Grains by Spark Plasma Sintering

Dense PbTiO₃ ceramics consisting of submicrometer-sized grains were prepared using the spark-plasma-sintering (SPS) method. Hydrothermally prepared PbTiO₃ (0.1 μm) was used as a starting powder. The powder was densified to ≳98% of the theoretical X-ray density by the SPS process. The average grain size of the spark-plasma-sintered ceramics (SPS ceramics) was ≲1 μm, even after sintering at 900°–1100°C, because of the short sintering period (1–3 min). The measured permittivity of the SPS ceramics showed almost no frequency dependence over the range 10¹–10⁶ Hz, mainly because pores were absent from the ceramics. The coercive field of the SPS ceramics was somewhat higher than that of conventionally sintered ceramics, which could be attributed to the small-grained microstructures of the SPS ceramics.     

Comparison Study on Additive Manufacturing (AM) and Powder Metallurgy (PM) AlSi10Mg Alloys

The microstructural and mechanical properties of AlSi10Mg alloys fabricated by additive manufacturing (AM) and powder metallurgy (PM) routes were investigated and compared. The microstructures were examined by scanning electron microscopy assisted with electron-dispersive spectroscopy. The crystalline features were studied by x-ray diffraction and electron backscatter diffraction. Room-temperature tensile tests and Vickers hardness measurements were performed to characterize the mechanical properties. It was found that the AM alloy had coarser Al grains but much finer Si precipitates compared with the PM alloy. Consequently, the AM alloy showed more than 100% increment in strength and hardness compared with the PM alloy due to the presence of ultrafine forms of Si, while exhibiting moderate ductility.     

Investigation of direct load management scheme with consideration of end‐user comfort

A direct load management scheme with two‐way communication, with consideration of end‐user comfort, is proposed. First, the control algorithm is developed and the data required to be transmitted between system operator and controllable loads are identified. Then, the actions of controllable air conditioners and the power adjustment of dispersed generators to eliminate overloads in a substation transformer are simulated. The results indicate that the proposed load management technique performs effectively to reduce overloads on the transformer while maintaining energy consumption in each load, and the performance is improved by coordination with the output of dispersed generators. © 2011 Wiley Periodicals, Inc. Electr Eng Jpn, 176(3): 19–28, 2011; Published online in Wiley Online Library ( wileyonlinelibrary.com ). DOI 10.1002/eej.21139     

Evaluation of the ATCA fast controller standard for ITER diagnostics

ITER project's long time span and the nature of the instrumentation and control (I&C) procurement procedures for the Plant Systems require that the ITER Organization defines and follows well recognized standards which are used both by the industry and in physics experiments. The ITER I&C standards are defined in the Plant Control Design Handbook (PCDH) [1]. The ITER Organization has selected PCI Express and Ethernet for IO intercommunication to be used for plant system instrumentation for fast controllers. The decision on the usage of serialized I/O bus protocols is based on the impressive performance and the commercial availability. The form factors that will be supported by CODAC include PXIe, MicroTCA, and AdvancedTCA platforms. While the PXIe form factor is already well established for instrumentation purposes through the PXI Systems Alliance (www.pxisa.org), the AdvancedTCA and MicroTCA platforms which were originally targeted for the telecommunications market (www.picmg.org) are currently optimized and specified for instrumentation use through the xTCA extensions for physics [2]. The objective of this study is the evaluation of an integrated ATCA controller design using only commercial components.