Contribution of metal vapor mass at periphery part of pulsed arc to electromagnetic force in weld pool

The arc welding has been used in various welding methods because it is inexpensive and high in strength after welding. However, it is a problem that accidents such as collapse of the bridge occur because of the welding defects. The welding of low cost and high productivity is required without the welding defects. The pulsed TIG welding is inexpensive and capable of high‐quality welding. The electromagnetic force contributing to penetration changes because the transient response of arc temperature and iron vapor generated from anode occurs. However, the analysis of pulsed TIG welding with metal vapor has been elucidated only metal vapor concentration near anode with transient phenomenon and heat flux. Thus, the theoretical elucidation of penetration depth with control factor has not been researched. In this paper, the contribution of metal vapor mass at the periphery part of pulsed arc to the electromagnetic force in the weld pool is elucidated. As a result, the iron vapor mass at periphery part decreased with increasing the frequency. The iron vapor was stagnated at axial center within one cycle. The electromagnetic force to the penetration depth direction in weld pool increased at axial center. Therefore, the metal vapor mass at periphery part plays an important role for the electromagnetic force increment at axial center.     

Structure and electrical characteristics of Ce4+-doped Ba2In2O5

The In-site of Ba₂In₂O₅ with Brownmillerite structure was partially substituted for Ce⁴⁺ ions in order to examine the doping effect on the order-disorder transition. Ba₂In_{2 – x} Ce _x O_{5 + x/2} (x = 0.1, 0.2, 0.3, 0.5, 1.0, and 1.5) were prepared by solid state reaction. X-Ray diffraction analyses of these powder samples demonstrated that Ba₂In_{2 – x} Ce _x O_{5 + x/2} (x = 0.1 and 0.2) possesses Brownmillerite structure. With increasing content of Ce⁴⁺ ion the crystal system of Ba₂In_{2 – x} Ce _x O_{5 + x/2} (x = 0.3, 0.5, and 1.0) changed to cubic perovskite structure above the order-disorder transition temperature of Ba₂In₂O₅. Arrhenius plots of the electrical conductivities of Ba₂In_{2 – x} Ce _x O_{5 + x/2} (x = 0.2, 0.3, and 1.0) exhibited no discontinuity. These compounds had high transference numbers of oxide ion above 973 k.     

Direct evidence of high DNA binding activity of transcription factor AP-1 in rheumatoid arthritis synovium

Green fluorescent protein (GFP) is increasingly being used in plant biology from the cellular level to whole plant level. At the cellular level, GFP is being used as an in vivo reporter to assess frequency of transient and stable transformation. GFP has also proven to be an invaluable tool in monitoring trafficking and subcellular localization of protein. At the organ level and up, many exciting applications are rapidly emerging. The development of brighter GFP mutants with more robust folding properties has enabled better macroscopic visualization of GFP in whole leaves and plants. One interesting example has been the use of GFP to monitor virus movement in and among whole plants. GFP is also emerging as a powerful tool to monitor transgene movement and transgenic plants in the field. In a proof-of-concept study, tobacco was transformed with a modified version of the GFP gene controlled by a constitutive (35S) promoter. GFP expression in progeny plants ranged from 0% to 0.5%, and approximately 0.1% GFP was the minimal amount needed for unambiguous macroscopic detection. GFP is the first truly in vivo reporter system useful in whole plants, and we project its usefulness will increase even further as better forms of GFP genes become available.     

Cell density-dependent DNA fragmentation and its suppression by heparin in primary culture of adult rat hepatocytes

We show here that the internucleosomal DNA fragmentation, which is a biochemical hallmark of apoptosis, was induced in a cell density-dependent manner in primary culture of adult rat hepatocytes. This DNA fragmentation could be suppressed by a gene expression inhibitor, indicating the active nature of this process. Moreover, the viability changes in high and low cell density cultures showed a tendency corresponding with the incidence of the DNA fragmentation in them. These results suggest that in hepatocytes there may be a cell density-dependent apoptosis mechanism. In this report, we also show that heparin could suppress this DNA fragmentation with high specificity, and the cell death to some extent.     

A 300-MHz 25-/spl mu/A/Mb-leakage on-chip SRAM module featuring process-variation immunity and low-leakage-active mode for mobile-phone application processor

An on-chip 1-Mb SRAM suitable for embedding in the application processor used in mobile cellular phones was developed. This SRAM supports three operating modes - high-speed active mode, low-leakage low-speed active mode, and standby mode - and uses a subdivisional power-line control (SPC) scheme. The combination of three operating modes and the SPC scheme realizes low-power operation under actual usage conditions. It operates at 300 MHz, with leakage of 25 /spl mu/A/Mb in standby mode, and 50 /spl mu/A/Mb at the low-leakage active mode. This SRAM also uses a self-bias write scheme that decreases of minimum operating voltage by about 100 mV.     

Thermal stability of reinforced Nb3Sn composite superconductor under cryocooled conditions

Several types of reinforced Nb₃Sn wires have been developed to prevent reduction of superconducting properties by applying a strong electromagnetic force. To fabricate a cryocooled magnet using those reinforced wires, we experimentally measured the minimum quench energy (MQE) under cryocooled conditions of some reinforced Nb₃Sn wires. As a result, it became clear that thermal stability expressed as MQE was controlled by the temperature margin between the temperature of the operating condition and the transition temperature from superconductivity to normal. Using the FEM analysis, it was realized that the cause of the decline in thermal stability for the reinforced wires was the low thermal conductivity of the reinforced materials.     

Systolic array implementation of block LMS algorithm

The authors derive the systolic array implementation of the block LMS algorithm, consisting of N processing elements, where N is the filter order. The resulting array attains an order-independent sampling rate. Computer simulation results show that the block LMS algorithm is faster than the delayed LMS algorithm, which has previously been implemented on systolic arrays