Controlling thickness to tune performance of high-mobility transparent conducting films deposited from Ga-doped ZnO ceramic target

Structure modification has been found to tune significantly the transparent-conducting performance, especially mobility and conductivity of hydrogenated Ga-doped ZnO (HGZO) films. The strong correlation between film thickness and mobility of the films is revealed. The mobility increases quickly with increasing the thickness from 350 to 900 nm, and then tends to be saturated at further thicknesses. A higher mobility than 50 cm²/Vs can be achieved, which is an extra-high value for polycrystalline ZnO films deposited by using the sputtering technique. The thickness-dependent mobility originates from scatterings on grain boundaries and dislocation-induced defects controlled by thin-film growth. Based on the Volmer-Weber model, an expansion model is built up to describe the thickness-dependent crystal growth of the HGZO films, especially at the thick films. As a result, the 800 nm-thick HGZO film obtains the highest performance with high mobility of 51.5 cm²/Vs, low resistivity of 5.3 × 10^?4 Ωcm, and good transmittance of 83.3 %.     

A unified method for optimal arbitrary pole placement

We consider the classic problem of pole placement by state feedback. We offer an eigenstructure assignment algorithm to obtain a novel parametric form for the pole-placing feedback matrix that can deliver any set of desired closed-loop eigenvalues, with any desired multiplicities. This parametric formula is then exploited to introduce an unconstrained nonlinear optimisation algorithm to obtain a feedback matrix that delivers the desired pole placement with optimal robustness and minimum gain. Lastly we compare the performance of our method against several others from the recent literature.     

Compression based clustering technique for enhancing accuracy in web scale videos

Multimedia Tools and Applications - Detection and clustering of commercial advertisements plays an important role in multimedia indexing also in the creation of personalized user content. In...     

Micro cam system driven by electrostatic comb-drive actuators based on SOI-MEMS technology

Microsystem Technologies - This paper reports a design and fabrication process of a micro cam system (MCS) with a flat-faced translating follower. The cam rim with cover diameter of 2.4 mm...     

Short packet communication in underlay cognitive network assisted by an intelligent reflecting surface

We propose short packet communication in an underlay cognitive radio network assisted by an intelligent reflecting surface (IRS) composed of multiple reconfigurable reflectors. This scheme, called the IRS protocol, operates in only one time slot (TS) using the IRS. The IRS adjusts its phases to give zero received cumulative phase at the secondary destination, thereby enhancing the end-to-end signal-to-noise ratio. The transmitting power of the secondary source is optimized to simultaneously satisfy the multi-interference constraints, hardware limitations, and performance improvement. Simulation and analysis results of the average block error rates (BLERs) show that the performance can be enhanced by installing more reconfigurable reflectors, increasing the blocklength, lowering the number of required primary receivers, or sending fewer information bits. Moreover, the proposed IRS protocol always outperforms underlay relaying protocols using two TSs for data transmission, and achieves the best average BLER at identical transmission distances between the secondary source and secondary destination. The theoretical analyses are confirmed by Monte Carlo simulations.     

Quantification of different effects occurring during fatigue tests on bituminous mixtures

Quantification of different effects (nonlinearity, heating, thixotropy, and fatigue) occurring during fatigue tests on bituminous mixtures is presented in this paper. A focus is given on the nonlinearity phenomenon. Continuous fatigue tests and a test with specific protocol (called fatigue tests to estimate biasing effects) were performed in tension/compression mode on cylindrical samples of the same material. The analysis of results reveals that reversible effects (nonlinearity, heating, and thixotropy) are important (more than 90% decrease at 100,000 cycles for a strain amplitude of 100 μm/m at 10 Hz) and cannot be ignored when interpreting classical fatigue tests. The nonlinearity effects respect the time‐temperature superposition principle, and they are more pronounced at “high” temperature (at the same frequency). Direction of nonlinearity curve in the Cole‐Cole axes is shown to be independent of temperature and frequency for the considered range.     

Facile synthesis of CsPbBr3/PbSe composite clusters

In this work, CsPbBr₃ and PbSe nanocomposites were synthesized to protect perovskite material from self-enlargement during reaction. UV absorption and photoluminescence (PL) spectra indicate that the addition of Se into CsPbBr₃ quantum dots modified the electronic structure of CsPbBr₃, increasing the band gap from 2.38 to 2.48 eV as the Cs:Se ratio increased to 1:3. Thus, the emission color of CsPbBr₃ perovskite quantum dots was modified from green to blue by increasing the Se ratio in composites. According to X-ray diffraction patterns, the structure of CsPbBr₃ quantum dots changed from cubic to orthorhombic due to the introduction of PbSe at the surface. Transmission electron microscopy and X-ray photoemission spectroscopy confirmed that the atomic distribution in CsPbBr₃/PbSe composite clusters is uniform and the composite materials were well formed. The PL intensity of a CsPbBr₃/PbSe sample with a 1:1 Cs:Se ratio maintained 50% of its initial intensity after keeping the sample for 81 h in air, while the PL intensity of CsPbBr₃ reduced to 20% of its initial intensity. Therefore, it is considered that low amounts of Se could improve the stability of CsPbBr₃ quantum dots.     

Development of a sequential robust–tolerance design model for a destructive quality characteristic

Robust design (RD) and tolerance design (TD) have received much attention from researchers and practitioners for more than two decades, and a number of methodologies for modeling and optimizing the RD and TD processes have been studied. However, there is ample room for improvement. Because most existing research considers RD and TD as separate research fields, the primary objective of this paper is to develop a sequential robust–tolerance design method to jointly determine the best factor settings and the closed-form solutions for the optimal specification limits. We then apply the proposed method to a destructive quality characteristic. Finally, a case study and sensitivity analyses are performed for verification purposes, and further studies are discussed.