Atomistic simulations of grain boundary migration in copper

While the motion of twist boundaries can be readily studied by atomistic simulations with molecular dynamics (MD) under the action of an elastic driving force, the approach fails for tilt boundaries. This is due to the interaction of the elastic stress with the grain boundary (GB) structure, which causes plastic strain by GB sliding. A novel concept, the orientation correlated driving force, is introduced to circumvent this problem. It is shown that this concept can be successfully applied to the study of the migration of tilt boundaries. The migration behavior of several twist and tilt GBs was investigated. The transition from low-to high-angle boundaries can be captured, and a structural transition of tilt boundaries was found at high temperatures, which also affected the migration behavior. The results compare well with experimental results of the motion high-angle boundaries, but for low-angle boundaries, the agreement is poor. This article is based on a presentation made in the “Hillert Symposium on Thermodynamics & Kinetics of Migrating Interfaces in Steels and Other Complex Alloys,” December 2–3, 2004, organized by The Royal Institute of Technology in Stockholm, Sweden.     

Sensor guided handling and assembly of active micro-systems

Positioning accuracies in the range of a few micrometers and below are necessary for the assembly of active micro-systems. In order to reach these accuracies, an assembly system for sensor guided micro-assembly is developed in the Collaborative Research Centre 516 “Design and manufacturing of active micro-systems”. The combination of a parallel robot with an integrated 3D vision sensor and a micro-gripper enables to reach relative positioning accuracies below 1 μm.     

Surfactant replacement therapy in acute respiratory distress syndrome from viral pneumonia

A modified natural surfactant was administered to a patient with life-threatening adult respiratory distress syndrome caused by viral pneumonia. Subsequently, there was a marked improvement in gas exchange. In order to assess the mechanism for improved oxygenation, computed tomography of the lungs was done. Quantitative analysis of the scans taken before and after surfactant administration indicates that improvement in gas exchange was largely due to the expansion of underinflated and collapsed lung areas. Although this is a single case report, it provides insight into the possible beneficial effect of instilled surfactant in severe respiratory distress from viral pneumonia.     

Effects of seat slope and hip flexion on spinal angles in sitting

Lumbar and thoracic spinal angles of 25 male and 25 female subjects were measured in four sitting postures, with standing angles used as reference. Subjects sat with either 90 deg or 65 deg of hip flexion on either flat or forward-sloping seats. Lumbar kyphosis was greatest when the flat seat/90-deg posture was adopted and least when the sloping seat/65-deg posture was adopted. The opposite was observed for the thoracic angles, and intermediate results were observed for the other two sitting postures. No statistically significant interactions were observed among seat slope, hip flexion, and subject sex. The findings are discussed with reference to the anatomy of sitting and factors influencing pelvic tilt and the implications for the ergonomic design of chairs.     

Growth Stresses in the Oxide Scales on TiAl Alloys at 800 and 900°C

In the oxidation of TiAl alloys, the role of scale-growth stresses formed during oxidation has, thus far, been unknown. In the present paper the oxide-growth stresses were investigated by the deflection-test method in monofacial oxidation (DTMO) accompanied by acoustic-emission measurements. On unmodified surfaces the growth stresses are compressive and reach levels of around –100 MPa. At the same time, significant acoustic emission occurs indicating that even under isothermal conditions, stresses are relieved by a scale-cracking mechanism. For oxide scales on TiAl surfaces, which had been ion implanted with chlorine before oxidation, a very thin protective alumina layer is formed which, however, develops growth stresses in the range of several GPa, accompanied by intensive acoustic emission. In all stress–time curves, a dynamic situation is observed. This consists of phases of stress relief by scale microcracking and phases of stresses increase due to crack healing and further oxide growth. As a result, the level of stress as a function of oxidation time, is characterized by an oscillating course.     

Rationalisierung des Zeichnungswesens im Chemie-Apparatebau

Rationalizing drawings for chemical apparatus . For small and medium-sized manufacturers of apparatus, producing drawings may constitute a disproportionate waste of time and personnel, particularly when no new designs are involved but only modification or improvement of drawings supplied by the customer. One possibility for rationalizing drawing is to simplify the old-fashioned approach by using symbols for frequently drawn or standard items, or by listing alphanumerically. This presumes a kind of systematization permitting determination of those symbols and their reasonable use, as well facilitating rationalization by means of data processing. There are different approaches to computer-aided drawing (from computer controlled drawing-board to interactive screens); here a CAD programme is presented which was especially developed for graphic presentation of chemical apparatus, and which can be used without learning a programming language.     

Thomas Fincke und die <Emphasis Type="Italic">Geometria rotundi</Emphasis>

Thomas Fincke (January 6^th, 1561–April 24^th, 1656), born in Flensburg (Germany), was one of the very most important and significant scientists in Denmark during the seventeenth century, a mathematician and astrologer and physician in the beginning of modern science, a representative of humanism and an influentual academic organizer. He studied in Strasbourg (since 1577) and Padua (since 1583) and received his M.D. in Basel (1587), he practised as a physician throughout his life (since 1587 or 1590) and became a professor at Copenhagen (1591). But he was best known because of his Geometriae rotundi libri XIIII (1583), a famous book on plane and spherical trigonometry, based not on Euclid but on Petrus Ramus. In this influentual work, in which Fincke introduced the terms tangent and secant and probable first noticed the Law of Tangents and the so-called Newton-Oppel-Mauduit-Simpson-Mollweide-Gauss-formula, he showed himself to be „abreast of the mathematics of his time“.