急性炎性疾病患者乳酸林格氏液液体动力学

目的:探索炎性疾病患者的乳酸林格氏液（Ringer's lactate,RL）液体动力学特征以及炎性生物标记物是否可以作为协变量影响RL分布和排泄。方法:本研究为前瞻性队列研究。选择40例美国麻醉医师分级（ASA）I-II级，腹腔镜下择期胆囊切除术（胆囊炎组，n=20）或者腹腔镜下急诊阑尾切除术（阑尾炎组，n=20）。所有患者麻醉诱导前开始输注RL，按15 mL/kg，35 min内输毕。采用酶联免疫（enzyme-linked immunosorbent assay,ELISA）方法测定血浆炎症（TNF-α,IL-10和CRP）或者内皮损伤生物标记物（syndecan-1,SDC-1）；利用血红蛋白（Hb）稀释-时间曲线和尿量，使用Phoenix软件，采用非线性混合效应模型分析计算RL液体动力学参数和协变量的影响。结果:与胆囊炎组相比，阑尾炎组RL从组织间隙到血浆的转运速率常数（k21）显著降低（14×10-3min-1 versus 35×10-3min-1;P=0.012）。阑尾炎组C反应蛋白（CRP）升高［中位数38.1(1.8-143.6) μg/mL versus 1.3(0.1-159.0) μg/mL;P<0.001］；与清醒状态相比，麻醉期间（输液开始后30～45 min），液体从中央室中到外周室的转运速率常数（k12）显著增加（57×10-3min-1 versus 32×10-3min-1；P<0.01）。清除速率常数（k10）降低90%（0.6×10-3min-1 versus 5.3×10-3min-1;P<0.001）。无论在清醒状态还是麻醉状态下低血压均能降低液体清除；炎症或者内膜损伤的生物标记物不能作为显著影响RL液体动力学参数的协变量。结论:阑尾炎或者胆囊炎患者术前输入液体后“炎症反应的生物标记物”不是RL的液体动力学的协变量，但是两组患者中，全身麻醉期间输入液体的清除率下降。     

The analysis and comparison of two novel kinds of focusing elements as reflectors

In this article, two novel kinds of focusing elements as reflectors are analyzed and compared. One is the grooved Fresnel zone plate reflector with continuous phase‐correcting. The other called subzone paraboloid reflector, has the profile that consists of a series of paraboloids. Their diffraction efficiencies and bandwidths are described. The two elements still preserve the advantages of Fresnel zone plates, namely, low profile, high efficiency, and simple fabrication. Two dual‐reflector antennas using the proposed focusing elements as the main reflectors are simulated and the results show that these antennas have good radiation performances. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 25:101–108, 2015.     

Performance investigation on a novel 3D wave flow channel design for PEMFC

Flow field structure can largely determine the output performance of Polymer electrolyte membrane fuel cell. Excellent channel configuration accelerates electrochemical reactions in the catalytic layer, effectively avoiding flooding on the cathode side. In present study, a three-dimensional, multi-phase model of PEMFC with a 3D wave flow channel is established. CFD method is applied to optimize the geometry constructions of three-dimensional wave flow channels. The results reveal that 3D wave flow channel is overall better than straight channel in promoting reactant gases transport, removing liquid water accumulated in microporous layer and avoiding thermal stress concentration in the membrane. Moreover, results show the optimal flow channel minimum depth and wave length of the 3D wave flow channel are 0.45 mm and 2 mm, respectively. Due to the periodic geometric characteristics of the wave channel, the convective mass transfer is introduced, improving gas flow rate in through-plane direction. Furthermore, when the cell output voltage is 0.4 V, the current density in the novel channel is 23.8% higher than that of conventional channel.     

Damage evolution in polymer due to exposure to high-pressure hydrogen gas

The use of hydrogen as a fuel is increasing exponentially, and the most economical way to store and transport hydrogen for fuel use is as a high-pressure gas. Polymers are widely used for hydrogen distribution and storage systems because they are chemically inert towards hydrogen. However, when exposed to high-pressure hydrogen, some hydrogen diffuses through polymers and occupies the preexisting cavities inside the material. Upon depressurization, the hydrogen trapped inside polymer cavities can cause blistering or cracking by expanding these cavities. A continuum mechanics–based deformation model was deployed to predict the stress distribution and damage propagation while the polymer undergoes depressurization after high-pressure hydrogen exposure. The effects of cavity size, cavity location, and pressure inside the cavity on damage initiation and evolution inside the polymer were studied. The stress and damage evolution in the presence of multiple cavities was also studied, because interaction among cavities alters the damage and stress field. It was found that all these factors significantly change the stress state in the polymer, resulting in different paths for damage propagation. The effect of adding carbon black filler particles and plasticizer on the damage was also studied. It was found that damage tolerance of the polymer increases drastically with the addition of carbon black fillers, but decreases with the addition of the plasticizer.     

可重构机器人模块间装配误差识别方法研究

基于对可重构机器人配对接口间位姿误差的分析划分,研制模块间装配误差在线测量识别接口,建立配对接口位姿误差与接口几何结构偏差之间的关系模型,进而建立配对接口位姿误差与配对接口内部测距传感器测量值之间的映射关系模型,提出一种基于内部测距传感器位移量的模块间装配误差在线识别、补偿方法.为验证方法的正确性,研制单关节?连杆试验平台.试验结果表明装配误差经在线识别、补偿后,连杆末端的位置误差平均值减少7倍多.     

Study on Wettability and Corrosion Behavior of Al2O3 Doped Polyurea Coatings

Protection of Metals and Physical Chemistry of Surfaces - The Al2O3 powder was added as a filler to polyurea and the effect of doping amount on Shore hardness and wetting property were...     

Effects of ethylene-octene copolymer (POE) on the brittle to ductile transition of high-density polyethylene/POE blends

Three kinds of ethylene-octene copolymers (POE) were melt-blended with high-density polyethylene (PE-HD) in different proportions. Detailed characterizations were conducted to analyze their structural differences of POE and its effects in toughening PE-HD. The higher molecular weight POE can improve the toughness of PE-HD. 60:40 PE-HD/POE is elongated to break up to 700% while impact strength is 84.7 kJ/m² at −30°C, which is 21-fold of PE-HD. In the brittle to ductile transition (BDT) during impact, the fracture mechanism changes from the crazing mode to the shear yield-plastic deformation mode. The BDT temperature decreases as the POE molecular weight and its content increase. The interface strength in tension is estimated to access their effects. The Boltzmann-type models were successfully extended to describe the typical S-shaped curves in BDT of notched impact strength vs POE content or temperature. The supplementary decay model is suggested for the attenuation in toughening. Transition map in impact is proposed to select the use range of composition (c ) and temperature (T ) for high toughness. The curves are converted into 3D graph of T -c -impact strength for illustrating their coupling-separate effects, and further into the contour map of impact strength in T -c space for finding their partial equivalence.     

Defocusing image to pattern contact holes using attenuated phase shift masks

The patterning of contact holes by selecting out-of-focus image plane (defocus) using attenuated phase shift masks (APSM) has been studied. Defocus is found to enhance the image modulation at low partial coherence for contact holes with negative local average of mask function. Semi-dense holes up to 130 nm in 8% APSM have been printed by 0.5 μm defocus at a partial coherence of 0.31 using KrF scanner with highest numerical aperture of 0.68. However, these holes were closed with in-focus imaging. Defocus is also found to be beneficial for patterning the pitches that have extensive side lobes with in-focus imaging.