Effects of non-thermal plasma treating wheat kernel on the physicochemical properties of wheat flour and the quality of fresh wet noodles

The effects of non-thermal plasma (NTP) on the physicochemical properties of wheat flour and the quality of fresh wet noodles ( FWN) were investigated. The results showed that NTP effectively decreased the total plate count (TPC), yeast and mould count (YMC) and Bacillus spp. in wheat flour. Wet gluten contents and the stability time reached the maximum when treated for 20 s. The viscosity of starch increased significantly after treatment due to the increased of damaged starch. The contents of secondary structure were altered to some extent, which was because that the ordered network structure of gluten protein broken. Furthermore, compared with the control, texture properties of FWN were enhanced significantly at 20 s, and the darkening rate of FWN was greatly inhibited due to the low polyphenol oxidase (PPO) activity. Consequently, the most suitable treatment was 500 W for 20 s, providing a basis for the application of NTP in flour products.     

Aluminum based reflective nanolens arrays to improve the effectiveness of ultraviolet inactivation of Escherichia coli O157:H7 and Listeria monocytogenes in water and a sucrose solution

Food Science and Biotechnology - Aluminum based reflective nanolens arrays were developed via a series of aluminum electropolishing and anodization steps with subsequent selective dissolution of...     

Preparation and characterization of mullite whisker reinforced ceramics made from coal fly ash

Ceramics with mullite whiskers were prepared from coal fly ash and Al₂O₃ raw materials, with AlF₃ used as an additive. The phase structures and microstructures of the ceramics were identified via X-ray diffraction and scanning electron microscopy, respectively. The results show that pickling of coal fly ash is an effective method for enhancing the flexural strength of ceramics. Sintering temperature and AlF₃ addition were also key factors influencing the creation of ideal ceramics. The ceramic made from pickled coal fly ash, 6?wt% AlF₃, and sintered at 1200?°C, exhibited the highest flexural strength of 59.1?MPa, and had a bulk density of 1.32?g/cm³ and porosity of 26.8%. The results show that ceramic materials made under these conditions are ideal candidates for manufacturing ceramic proppants for the exploitation of unconventional oil and gas resources.     

SUBSCRIPTION 2018

正Four issues per volume a year,CHINA’S REFRACTORIES is distributed worldwide by airspeed delivery at no extra cost to subscribers.     

Defocusing image to pattern contact holes using attenuated phase shift masks

The patterning of contact holes by selecting out-of-focus image plane (defocus) using attenuated phase shift masks (APSM) has been studied. Defocus is found to enhance the image modulation at low partial coherence for contact holes with negative local average of mask function. Semi-dense holes up to 130 nm in 8% APSM have been printed by 0.5 μm defocus at a partial coherence of 0.31 using KrF scanner with highest numerical aperture of 0.68. However, these holes were closed with in-focus imaging. Defocus is also found to be beneficial for patterning the pitches that have extensive side lobes with in-focus imaging.     

合成己二腈反应技术研究——(Ⅴ)己二腈工业反应过程模拟与反应器改造

对己二腈工业反应器提出了两釜串联带回流的模型,通过模拟计算得出模型的级间返混系数 f=6的结论。该模型能较好地预测工业反应器中物料组分浓度变化和气、液两相的流动特性;指出了现工业反应器的鼓泡中和段体积偏小是造成己二酸浓度偏高的关键;提出了可以通过增加串连一个鼓泡预反应段的改造方案,能有效地降低己二酸的浓度,从7%降至4%左右,从而能较好地减缓腐蚀和结焦。     

Adaptive motion control using neural network approximations

In this paper, we present a new adaptive technique for tracking control of mechanical systems in the presence of friction and periodic disturbances. Radial Basis Functions (RBFs) are used to compensate for the effects of nonlinearly occurring parameters in the friction and periodic disturbance model. Theoretical analysis, such as stability and transient performance, is provided. Furthermore, the performance of the adaptive RBF controller and its non-adaptive counterpart are compared.     

Topology preservation of template-based 6-subiteration reduction operations

Generally, a reduction operation (e.g., thinning and shrinking) on 3D binary images can be represented as a set of reduction templates where every object voxel of the image satisfying any template is turned to a background voxel. Generally, it is rather difficult, error-prone and time-consuming for verifying the topological soundness of a 3D parallel reduction operation. This paper proposes sufficient conditions of time complexity O(n) for verifying the topological soundness of 3D parallel 6-subiteration reduction operations of n templates where such a kind of 3D reduction operations is performed alternatively from the six orthogonal directions to turn object voxels to background voxels. By such sufficient conditions, the topology soundness of a 3D 6-subiteration parallel reduction operation can be verified by checking each and every of its templates.     

Control of discrete time nonlinear systems with a time-varying structure

In this paper, we present a control methodology for a class of discrete time nonlinear systems that depend on a possibly exogenous scheduling variable. This class of systems consists of an interpolation of nonlinear dynamic equations in strict feedback form, and it may represent systems with a time-varying nonlinear structure. Moreover, this class of systems is able to represent some cases of gain scheduling control, Takagi-Sugeno fuzzy systems, as well as input-output realizations of nonlinear systems which are approximated via localized linearizations. We present two control theorems, one using what we call a “global” approach (akin to traditional backstepping), and a “local” approach, our main result, where backstepping is again used but the control law is an interpolation of local control terms. An aircraft wing rock regulation problem with varying angle of attack is used to illustrate and compare the two approaches.