变压器内部故障在线检测方法仿真及误差分析

为研究变压器内部故障在线检测方法的有效性及抗干扰性,搭建实际变压器的非线性三维有限元模型.对变压器常见几种类型的内部故障进行详细的结构仿真,通过"场-路耦合法"构建各类型故障的ΔV-I1轨迹.同时,通过对正常绕组的测量信号设置一定的误差,构建了考虑测量误差时的误差轨迹.在此基础上,将正常时的标准轨迹、误差轨迹和各种类型的故障轨迹进行对比分析,通过对ΔV-I1轨迹特征差异的定性分析与定量计算,验证该方法在实际应用中的有效性,总结判断各类型故障的规则,同时针对测量误差所造成的干扰提出了建议.     

Robust Control of Permanent Magnet Synchronous Motors

In this paper, permanent magnet synchronous motors (PMSMs) are investigated. According to the feature of PMSMs, a novel state equation of PMSMs is obtained by choosing suitable state variables. Based on the state equation, robust controllers are designed via interval matrix and PI control idea. In terms of bilinear matrix inequations, sufficient conditions for the existence of the robust controller are derived. In order to reduce the conservation and the dependence on parameter, the control inputs of PMSMs are divided into two parts, a feedforward control input and a feedback control input, and relevant sufficient conditions for the existence of the controller are obtained. Because of the suitable choice of state variables, the proposed control strategies can cope with the load uncertainty and have robustness for disturbance. Finally, simulations are carried out via Matlab/Simulink soft to verify the effectiveness of the proposed control strategies. The performance of the proposed control strategies are demonstrated by the simulation results.      

High‐performance thermosets with tailored properties derived from methacrylated eugenol and epoxy‐based vinyl ester

A renewable chemical, eugenol, is methacrylated to produce methacrylated eugenol (ME) employing the Steglich esterification reaction without any solvent. The resulting ME is used as a low‐viscosity co‐monomer to replace styrene in a commercial epoxy‐based vinyl ester resin (VE). The volatility and viscosity of ME and styrene are compared. The effect of ME loading and temperature on the viscosity of the VE–ME resin is investigated. Moreover, the thermomechanical properties, curing extent and thermal stability of the fully cured VE–ME thermosets are systematically examined. The results indicate that ME is a monomer with low volatility and low viscosity, and therefore the incorporation of ME monomer in VE resins allows significant reduction of viscosity. Moreover, the viscosity of the VE–ME resin can be tailored by adjusting the ME loadings and processing temperature to meet commercial liquid molding technology requirements. The glass transition temperatures of VE–ME thermosets range from 139 to 199 °C. In addition, more than 95% of the monomer is incorporated and fixed in the crosslinked network structure of VE–ME thermosets. Overall, the developed ME monomer exhibits promising potential for replacing styrene as an effective low‐viscosity co‐monomer. The VE–ME resins show great advantages for use in polymer matrices for high‐performance fiber‐reinforced composites. This work is of great significance to the vinyl ester industry by providing detailed experimental support. © 2018 Society of Chemical Industry     

软交换与3G网络互通关键技术分析

就软交换网络和WCDMAR4网络互通的关键技术进行了分析和探讨，并借此提出了对互通节点的技术要求。     

国有科研单位人才流失原因分析及对策

近年来,国有科研单位,尤其是地处经济不发达地区的国有科研单位,出现了较为严重的人才流失现象,一定程度上影响和制约了国有科研单位的发展。通过对国有科研单位人才流失原因的分析,提出了相应的对策。     

干涉型激光直写技术用于光盘防伪

利用作者研制的干涉型激光直写系统，阐述了干涉型激光直写设计OVD的方法，防伪特征，介绍了应用于光盘防伪的OVD技术和应用前景，给出了实验结果。     

行波管质量与可靠性信息管理系统的设计

本文从应用角度简要介绍了《行波管质量与可靠性信息管理系统》的研制背景，数据库的数据来源，数据结构，系统构成及功能特点。     

小型RFCO2激光器的电路保护

本文详细分析研究了小型射频CO2激光器经常出现的故障现象(过压、负载短路故障),并介绍了相应的保护措施,对实际工作有显着指导意义。     

局部剩余偏移与常速叠前偏移成像

如果需要将一个特定局部时空域中的地震反射波归位到它们的实际位置,则我们不必在整个时空域而只需在这个局部时空域对其进行偏移,同样能达到波场归位的目的。其差別仅是采用的速度不同而已.这样能大大地减小偏移的作用区域。采用这种局部偏移的方法进行常速叠前偏移结果的剩余速度偏移,可以完全消除叠前偏移剖面上由于速度变化引起的倾斜反射界面的错断现象。这样在进行叠前偏移时可采用较少的速度个数,减少叠前偏移的计算量。采用该方法作剩余速度偏移可以减少波场成像时的计算量,从而使得常速叠前偏移成为一种处理效果好、处理效率高的实用处理技术。