Development of –1 MV DC Filter and High‐Voltage DC Measurement Systems for ITER NBI

This paper presents the development results of a ?1 MV dc filter and dc measurement systems for an ITER (International Thermonuclear Experimental Reactor) neutral beam injector (NBI) system. High accuracy of 0.5% and fast responsivity of 3.3 μs, ?3 dB are required for the dc measurement systems: both dc voltage dividers and DCCTs. Circuit design and thermal flow design were carried out to clarify and minimize their effects on the accuracy and responsivity. The validity of the established design was demonstrated by the actual‐product tests; temperature rise of each components fell below the allowable value; inner components of dc filter withstood dc ?1.2 MV; each voltage divider accurately measured the voltage during the dc ?1.2 MV withstand voltage test; the voltage dividers and the DCCTs were adequate to the requirements of responsivity (3.3 μs, ?3 dB).     

Vacuum Insulation and Achievement of 980 keV, 185 A/m~2 H-Ion Beam Acceleration at JAEA for the ITER Neutral Beam Injector

Vacuum insulation of 1 MV is a common issue for the HV bushing and the accel- erator for the ITER neutral beam injector (NBI). The HV bushing as an insulating feedthrough has a five-stage structure and each stage consists of double-layered insulators. To sustain 1 MV in vacuum, reduction of electric field at several triple points existing around the double-layered insulators is a critical issue. To reduce electric field simultaneously at these points, three types of stress ring have been developed. In a voltage holding test of a full-scale mockup equipped with these stress rings, 120% of rated voltage was sustained and the voltage holding capability required in ITER was verified. In the MeV accelerator, whose target is the acceleration of a H ion beam of 1 MeV, 200 A/m 2 , the gap between the grid support was extended to suppress breakdowns triggered by electric field concentration at the edge and corner of the grid support. This modi- fication improved the voltage holding capability in vacuum, and the MeV accelerator succeeded in sustaining 1 MV stably. Furthermore, it appeared that the H ions beam was deflected and a part of the beam was intercepted at the acceleration grid. This causes high heat load on the grids and breakdowns during beam acceleration. To suppress the direct interception, a new grid was designed with proper aperture displacement based on a three dimensional beam trajectory analysis. As a result, 980 keV, 185 A/m 2 H ion beam acceleration has been demonstrated, which is close to the ITER requirement.     

INFLUENCE OF DESIGN AND OPERATING CONDITIONS ON THE SYSTEM PERFORMANCE OF A TWO-STAGE ADSORPTION CHILLER

This article aims at clarifying the possible design and operating conditions for silica gel-water adsorption refrigeration cycles driven by near-ambient temperature waste heat sources (between 45 and 75°C) with relatively small regenerating temperature lifts (15 to 45 K). A two-stage silica gel-water advanced adsorption chiller is introduced and a simulation model of the chiller was developed to analyze the influence of operating and design conditions on the system performance (coefficient of performance, COP, and cooling capacity). It was hypothesized that the proposed chiller can be driven by low temperature waste heat at 55°C to produce effective cooling. Simulation results show that the operating conditions such as cycle time and hot and cooling water inlet temperature have an influential effect on cooling capacity and COP. COP is proportional to cycle time and heat transfer coefficient as well as inversely proportional to the cooling water inlet temperature, while there are optimum values of hot water temperature and silica gel weight for maximum COP. Cooling capacity mainly improves with the addition of silica gel weight and decreases as cooling water temperature increases. Simulation results also revealed that the system performance can be improved significantly by setting the design and operating conditions optimally.     

Oxygen-Sensor-Based Simple Assay of Histamine in Fish Using Purified Amine Oxidase

Oxygen consumption was measured by an oxygen sensor after addition of purified fungal amine oxidase to fish extracts. The oxidation of histamine to imidazoleacetaldehyde proceeded stoichiometrically. Based on the equimolar relationship between histamine and oxygen consumption, histamine was determined selectively by the oxygen sensor. Neither sample pretreatment removing interfering materials nor daily calibration by histamine standard was required. Histamine contents in scombroid fish were determined rapidly with good accuracy. AOAC and oxygen sensor methods showed a very high correlation (r=0.999, n=6).     

Elucidation of mechanism of aminoreductone formation in the Maillard reaction of lactose

The aim of this study was to elucidate the formation mechanism of aminoreductone, an important indicator for estimating the extent of Maillard reaction of lactose and amino compounds. Using the model system of lactose and butylamine, the model solution of lactose and milk proteins, and milks, it was concluded that d ‐galactose was liberated at the same time as the generation of aminoreductone. It was shown that the extent of the Maillard reaction and the lactose degradation during heating depended closely on the concentration ratio of amino group/lactose in the sample solution.     

Actual Congestion and Effect of Charger Addition in the Quick Charger Station: Case Study Based on the Records of Expressway

There were 18 electric vehicles, in average, per quick charger (QC), in Japan as of 2012, and this value may increase by a factor of several dozen by 2020. It is, therefore, necessary to model and analyze QC service, identify the causes of wait time, and provide countermeasures to avoid significant QC congestion and to encourage the spread of QC stations. This research analyzed usage data of a QC installed at an existing service area on expressway, and showed the characteristics of QC demand as distribution functions. QC service was modeled as a queuing problem, and simulations were carried out using derived distribution functions. The results showed that the QC station needs additional charger in the case of daily charging times over 10 times.     

DESIGN OF A NONIMAGING FRESNEL LENS FOR SOLAR CONCENTRATORS

An optimum convex shaped nonimaging Fresnel lens is designed following the edge ray principle. The lens is evaluated by tracing rays and calculating a projective optical concentration ratio. This Fresnel lens is intended for use in evacuated tube type solar concentrators, generating mid-temperature heat to drive sorption cycles, or provide industrial process heat. It can also be used along with a secondary concentrator in photovoltaic applications.