M2M energy saving strategy in 5G millimeter wave system

Telecommunication Systems - Machine to Machine technology has a broad application prospect in the 5G network, but there is a bottleneck in the energy consumption of intelligent devices powered by...     

Influence of CO2 inleakage on the slight-alkalization of generator internal cooling water

The slight-alkalization of generator internal cooling water (GICW) is widely used to inhibit the corrosion of hollow copper conductor and thereby ensure the safe operation of the generator. CO₂ inleakage is increasingly identified as a potential security risk for GICW system. In this paper, the influence of CO₂ inleakage on the slight-alkalization of GICW was theoretically discussed. Based on the equilibriums of the CO₂-NaOH-H₂O system, CO₂ inleakage saturation was derived to quantify the amount of the dissolved CO₂ in GICW. This parameter can be directly calculated with the measured conductivity and the [Na⁺] of GICW. The influence of CO₂ inleakage on the slight-alkalization conditioning of GICW and the measurement of its water quality parameters were then analyzed. The more severe the inleakage, the narrower the water quality operation ranges of GICW, resulting in the more difficult the slight-alkalization conditioning of GICW. The temperature calibrations of the conductivity and the pH value of GICW show non-linear correlations with the amount of CO₂ inleakage and the NaOH dosage. This study provides insights into the influence of CO₂ inleakage on the slight-alkalization of GICW, which can serve as the theoretical basis for the actual slight-alkalization when CO₂ inleakage occurs.     

ZY6400/23/47型掩护式液压支架偏置改造

铁煤集团大兴矿(以下简称"大兴矿")2019年产240万t,井田位于铁法煤田的西南角,火成岩侵入及地质构造复杂,煤层破坏程度严重[1-2]。受火成岩影响,煤层瓦斯含量大幅增加[3-4],渗透性能差,力学强度低,煤的含水率低,自然发火期较短,是煤与瓦斯突出矿井。在采煤过程中,防治自然发火是重中之重,综采设备在设计初期未考虑实施灭火的操作空间,为此,笔者提出通过改造综采设备增加实施灭火的操作空间,降低出现自然发火灾害时防治的难度,保证采煤安全。     

钢管套筒灌浆连接轴向受拉性能模拟试验研究

为研究钢管套筒灌浆连接轴向受拉破坏过程及破坏机理，试验中设计了16组48个钢管套筒灌浆连接试件，试件采用钢板代替圆钢管，并进行静载试验。分析了灌浆料裂缝扩展过程、荷载-相对位移曲线，并对抗剪键高距比、灌浆料厚度、侧向力等因素对破坏过程及承载力的影响进行分析。结果表明：对于不设置抗剪键的套筒灌浆连接试件，斜裂缝随机产生，裂缝分布不均匀；对于设置抗剪键的套筒灌浆连接试件，裂缝首先出现在底部抗剪键位置处，与水平方向夹角约为30°，随后在中部和上部抗剪键位置处分别出现斜裂缝。由于每个抗剪键上荷载分担并不均匀，与抗剪键接触的灌浆料逐渐达到极限压应力，达到极限状态时，承载力全部由抗剪键间的机械咬合力承担，在连接承载力中，可忽略摩擦力和胶结力作用。随着抗剪键高距比h/s增大，各试件初始剪切刚度相差不大，承载力增大，但增幅逐渐减小，建议抗剪键高距比0.06g/s>0.3，同时需要满足灌浆料灌注的施工要求。     

喷油方式对斜齿轮齿面温度的影响

为探讨喷油方式对齿面温度的影响，以斜齿轮为研究对象，通过CFD仿真和试验研究不同喷油方式对斜齿轮齿面温度的影响。针对斜齿轮喷油润滑过程的特点，分析其齿面摩擦生热量，简化轮齿喷油润滑计算模型，并基于CFX进行齿面对流换热仿真研究，得到了不同喷油方式下的齿面温度；基于功率开放式斜齿轮试验平台，对不同喷油方式下的齿面温度进行了试验测量，与仿真计算结果进行对比分析。结果表明：在高速重载斜齿轮传动系统中，啮出侧喷油润滑的方式比啮入侧喷油润滑方式的冷却降温效果要好。