利用高频结构仿真器分析波导魔T

高频结构仿真器（HFSS）是一种微波器件设计软件，该软件界面友好，通过仿真计算减小了调试工作量，使得微波器件的设计变得简单易行。本文利用HFSS对波导魔T进行了仿真分析，得到了该器件的S参数和动、静态场的分布情况，并对该器件进行了优化设计。     

SO4^2-／ZrO2固体超强酸的制备及其催化合成ETBE的研究

采用沉淀一浸渍法制备了负载型SO4^2-／ZrO2固体超强酸催化剂，运用IR、XRD等方法表征所制备催化剂的物化性质。结果表明，所制备的催化剂具有固体超强酸催化剂的特征，酸性与焙烧温度有关，适当提高焙烧温度有利于样品酸强度的提高，但焙烧温度过高会导致脱硫；浸渍液H2SO4浓度高有利于提高催化剂的硫含量，但是浓度过高，会在催化剂上形成硫酸盐，从而降低催化剂的比表面积和酸性。采用制备的催化剂气相催化乙醇与叔丁醇合成乙基叔丁基醚反应，乙基叔丁基醚的选择性为54．71％。     

复杂土坝的渗流安全分析评价

根据福华山土坝的渗流观测资料,建立了测压管水位的回归统计模型,定量分析了各影响量(水位分量、时效分量)对测压管水位的影响效应。在此基础上,结合观测资料,采用有限元法反演了大坝各填筑区的渗透系数,并综合评价了大坝的渗流性态。     

Oxidation of Hastelloy-XR Alloy for Corrosion-Resistant Glass-Coating

The oxidation behavior of Hastelloy-XR alloy was investigated to obtain the optimum surface condition for corrosion-resistant glass-coatings. The surface morphology of oxide scales changed significantly with variation of temperatureand oxygen partial pressure (po2 ). The oxidation kinetics was mainly parabolic independent of oxidation conditions.The oxide scales were consisted of inner Cr2O3 and outer spinel layers. The phase component of spinel layers wereMn1.5Cr1.5O4 and (Mn,Ni)(Cr,Fe)2O4 for the oxygen partial pressures po2<10 kPa and po2>10 kPa, respectively.The optimum oxidation condition to obtain an oxide scale for well-adhered glass-coating to the substrate was 1248 Kand po2 =0.01 kPa for the oxidation time of 43 ks.     

换热器NH3泄漏的危害及防治措施

2005年8月,中国石油天然气股份有限公司辽阳石化分公司炼油厂第二循环水场水质出现异常情况.经调查分析,发现是脱硫装置E3410A换热器介质NH3泄漏后进入循环冷却水系统所致.介绍了NH3泄漏后的水质变化趋势及危害,并提出了防治措施.     

Effect of Stoichiometry on Properties of Rare-Earth-Based Hydrogen Storage Alloy for Nickel-Metal Hydride Secondary Battery

Effect of stoichiometry on microstructures, electrochemical properties and PCT characteristics of the alloys MI(Ni0.71Co0.15-Al0.06Mn0.08)x (MI=Lanthanum-rich Michmetal, x=4.6~5.2) have been investigated. The lattice constants a, c, and cellvolumes of non-stoichiometric alloys are bigger than those of the stoichiometric alloy. With the increasing stoichiometry x,the value of a decreases, and the value of c and cell volume increases except for those of the stoichiometric alloy; the plateaupressure of PCT curve, discharge capacity and cycling stability all increase. The alloy with x=5.2 shows the highest dischargecapacity and the best cycling stability among the studied alloys.     

工艺因素对金属封装外引线弯曲疲劳的影响

考察了金属封装外壳制造工艺对外引线弯曲疲劳的影响,发现电镀镍是导致外引线弯曲次数明显减少的最主要工艺步骤,且随镀镍层厚度的增加,弯曲次数减少。此外还讨论了外引线的氢含量和晶粒度对引线抗疲劳能力的影响。     

Pruning Redundant Alarm Correlation Patterns

1　ＩｎｔｒｏｄｕｃｔｉｏｎＴｈｅｓｔｉｃｋｉｎｇｐｏｉｎｔｏｆａｓｓｏｃｉａｔｉｏｎｒｕｌｅａｌｇｏｒｉｔｈｍｓｄｅｐｅｎｄｓｏｎｅｆｆｅｃｔｉｖｅｌｙｆｉｎｄｉｎｇａｌｌｃｏｒｒｅｌａｔｉｏｎｐａｔｔｅｒｎｓｔｈａｔｓａｔｉｓｆｙｖａｌｕｅｒｅｑｕｉｒｅｍｅｎｔｉｎｔｈｅｍａｇｎａｎｉｍｉｔｙｏｆｄａｔａ.Ｂｕｔｔｈｅａｌｇｏｒｉｔｈｍｓａｌｓｏｂｒｉｎｇａｎｅｇａｔｉｖｅｅｆ ｆｅｃｔ:ｔｈｅｎｕｍｂｅｒｏｆａｓｓｏｃｉａｔｉｏｎｒｕｌｅｓｉｓｖｅｒｙｌａｒｇｅ.Ａｌｓｏｉｎｆｏｒｍａｔｉｏｎ…