基于小角度高位技术的钻孔初采期瓦斯治理

回采工作面初采期瓦斯涌出不均衡,易出现瓦斯超限现象。针对新源煤矿近距离煤层群开采、瓦斯涌出量大等特点,提出了小角度高位钻孔抽采治理初采期瓦斯的方法;2219工作面应用实践表明,初采期内,小角度高位钻孔抽采瓦斯纯量最高5.25m3/min,瓦斯抽采率64.02%,回风流瓦斯浓度最高为0.32%,上隅角最高瓦斯浓度0.96%,未出现瓦斯超限现象,取得了很好的初采期瓦斯治理效果。     

锚栓用量对纯锚固岩棉保温系统抗风压性能的影响

采用ETAG 004:2013《外墙外保温薄抹灰系统欧洲技术认证指南》中规定的静态泡沫块法,测试在单位面积上使用不同数量锚栓的岩棉板外保温系统的抗风压性能。通过试验可以得出:在混凝土墙体上单纯采用敲击式锚栓锚固岩棉板外保温系统时,拉伸强度可达12.9 k Pa;单位面积增加锚栓的使用量可以提高系统的抗拉承载力,但在不同条件下增加相同数量锚栓对系统抗风载能力提高的程度不同;在普通混凝土墙中,单纯锚固岩棉板保温系统破坏时,单个锚栓承载力平均值的最大值约为其拉拔承载力的50.3%。     

Distributed learning consensus control based on neural networks for heterogeneous nonlinear multiagent systems

This paper considers a novel distributed iterative learning consensus control algorithm based on neural networks for the control of heterogeneous nonlinear multiagent systems. The system's unknown nonlinear function is approximated by suitable neural networks; the approximation error is countered by a robust term in the control. Two types of control algorithms, both of which utilize distributed learning laws, are provided to achieve consensus. In the provided control algorithms, the desired reference is considered to be an unknown factor and then estimated using the associated learning laws. The consensus convergence is proven by the composite energy function method. A numerical simulation is ultimately presented to demonstrate the efficacy of the proposed control schemes.     

基于图像增强的去雾快速算法的FPGA实现

基于图像增强方法，本文提出了一种使用亮度映射的图像去雾快速算法。此算法通过调整室外多雾场景图像的对比度，提高了雾中物体的辨识度。算法的复杂度低、处理延迟小，实时性高，利于FPGA的实现。实现时不需外存储器，延时为ns级，并提供了强度调节接口，以适应较广的应用环境。     

异质结光晶体管的研究与进展

回顾了异质结光晶体管(HPT)在近年来的重要进展,综合分析了HPT的工作原理以及影响其性能的主要参数。综述了不同材料制作的HPT的研究现状,得出了目前限制HPT发展的主要因素及当前应重点解决由于基区表面复合等效应导致的增益下降和由于结电容的充放电限制的响应带宽等问题的结论。     

微流控分析芯片制作中的低温键合技术

微流控分析芯片制作方法的研究是微流控分析的基础。制作性能良好的微流控分析芯片时,基片与盖片的键合技术十分重要。本文针对近年来发展迅速的低温键合技术,对各种方法进行了评价,并对其发展前景进行了展望。     

天然气吸附储存脱附过程的动态模拟

通过热动力学计算,认识了脱附过程当中储罐内温度剖面分布的典型特征:储罐轴心处的温度下降幅度最大。分析了脱附过程当中储罐壁的热交换、吸附剂的导热系数以及储罐内的初始压力对储罐内的温度剖面的影响。结论是加强储罐外壁的热交换、增大吸附剂的导热系数皆能改善吸附储罐内的温度剖面。     

The Synthesis of Sulfated Titanium Oxide Nanotubes

TiO₂ nanotubes can be prepared in gram quantities by treating anatase TiO₂ powder with concentrated NaOH solution. These TiO₂ nanotubes acquired strong acidity after being impregnated with sulfuric acid solution and calcined at 300 °C. The anatase TiO₂ powder used to prepare the nanotube did not catalyze the esterification between cyclohexanol and acetic acid, while sulfated TiO₂ nanotubes were very reactive toward the esterification reaction.     

Fabrication of multi-walled carbon nanotube reinforced polyelectrolyte hollow nanofibers by electrospinning

Hybrid hollow multi-walled carbon nanotubes (MWCNTs)/polyelectrolytes (PE) nanofibers were prepared by a combination of the electrospinning method and layer-by-layer (LbL) technique. The mixed polystyrene (PS)/MWCNTs nanofibers were obtained by electrospinning method, which were employed as templates to self-assembly multilayered polyelectrolytes by LbL technique. Hollow MWCNTs/PE nanofibers were obtained by selectively removed part of the template: PS, which is confirmed by Raman spectra, transmission electron microscopy (TEM) and scanning electron microscopy (SEM).