排序方式: 共有88条查询结果,搜索用时 15 毫秒
1.
为适应极大规模集成电路(GLSI)集成度按摩尔定律飞速发展的需要,同时解决国际酸性化学机械平坦化(CMP)技术存在的多项问题,本文研发了以多羟多胺为螯合剂的不含副作用大的苯并三唑(BTA)的碱性铜布线抛光液.实验结果表明:研发的碱性铜抛光液在常态下对铜几乎不反应(20/min),而在常压(2 psi)CMP下,能够快速地去除铜膜,去除速率(RR)高达8 235/min(工业要求5 000/min).凹处自钝化,凸处快速率,实现了高的平坦化效率.8层铜布线平坦化结果表明,60s可消除约1.162 m的高低差,且单层图形片基本实现平坦化(高低差<10 nm),抛光后表面粗糙度低(0.178 nm),表面洁净度高. 相似文献
2.
3.
针对不合腐蚀抑制剂苯并三氮唑(BTA)的碱性铜粗抛液,通过对3英寸(1英寸=2.54 cm)铜片上的动态抛光速率和静态腐蚀速率的研究来模拟评估氧化剂对晶圆表面平坦化的影响.在12英寸铜镀膜片和TM1图形片上分别研究氧化剂体积分数对表面平坦化的影响.实验结果表明:动态抛光速率和静态腐蚀速率均随着氧化剂体积分数的增加先逐渐增大,达到最大值,然后下降,趋于平缓.片内非均匀性和剩余高低差均随H2O2体积分数的增加,先呈下降趋势,后缓慢上升.当氧化剂体积分数为3%时,动态去除速率(vRR)为398.988 nm/min,静态腐蚀速率vER为6.834 nm/min,vRR/vER比值最大,片内非均匀性最小为3.82%,台阶高低差最小为104.6 nm/min,此时晶圆片有较好的平坦化效果. 相似文献
4.
为实现铜互连阻挡层化学机械抛光的高平坦化,研究了阻挡层抛光液中表面活性剂的作用。在抛光液中分别添加非离子型表面活性剂异辛醇聚氧乙烯醚(JFC-E)、本课题组研发的Ⅱ型活性剂以及复合表面活性剂,研究其对阻挡层CMP中铜和正硅酸乙酯(TEOS)去除速率及一致性的影响。实验结果表明,表面活性剂不仅可以改善Cu和TEOS的去除速率一致性和晶圆全局一致性,还可以降低铜表面的粗糙度,通过复配两种不同的表面活性剂,可以提高Cu和TEOS的去除速率,使Cu和TEOS的剩余厚度片内非均匀性(WIWNU)分别降低至1.39%和1.38%,铜表面粗糙度从5.25 nm降至1.51 nm。基于实验结果,研究并提出了表面活性剂影响抛光液润湿性,从而改善片内非均匀性和铜表面质量的机理。 相似文献
5.
6.
碱性条件下,非离子型表面活性剂在阻挡层化学机械平坦化中起着重要的作用。分别对阻挡层材料Cu、Ta以及SiO2介质进行抛光,然后测量铜表面粗糙度。对含有不同浓度活性剂的抛光液进行接触角和Zeta电位的测试,并对活性剂的作用机理进行分析。活性剂体积分数达到3%时,铜表面粗糙度可达0.679 nm,抛光液在铜膜表面的接触角低至10.25°,Zeta电位达到-50.2 mV。实验结果表明,活性剂在减小粗糙度的同时可提高抛光液的湿润性和稳定性,便于抛光后清洗和长时间放置。 相似文献
7.
The evaluation methods of planarization capability of copper slurry are investigated.Planarization capability and material removal rate are the most essential properties of slurry.The goal of chemical mechanical polishing(CMP) is to achieve a flat and smooth surface.Planarization capability is the elimination capability of the step height on the copper pattern wafer surface,and reflects the passivation capability of the slurry to a certain extent.Through analyzing the planarization mechanism of the CMP process and experimental results,the planarization capability of the slurry can be evaluated by the following five aspects:pressure sensitivity,temperature sensitivity,static etch rate,planarization efficiency and saturation properties. 相似文献
8.
9.
盐酸胍在阻挡层化学机械抛光中对速率选择性及表面形貌的影响 总被引:1,自引:1,他引:0
We propose an alkaline barrier slurry containing guanidine hydrochloride(GH) and hydrogen peroxide.The slurry does not contain any corrosion inhibitors, such as benzotriazole(BTA). 3-inch samples of tantalum copper and oxide were polished to observe the removal rate. The effect of GH on removal rate selectivity along withhydrogenperoxidewasinvestigatedbycomparingslurrycontainingGHandH2O2withslurrycontainingonly GH. Details about the tantalum polishing mechanism in an alkaline guanidine-based slurry and the electrochemical reactions are discussed. The results show that guanidine hydrochloride can increase the tantalum polishing rate and the selectivity of copper and barrier materials. The variation of the dishing and wire line resistance with the polishing time was measured. The dishing value after a 300 mm pattern wafer polishing suggests that the slurry has an effective performance in topography modification. The result obtained from the copper wire line resistance test reveals that the wire line in the trench has a low copper loss. 相似文献
10.
We have proposed a TSV (through-silicon-via) alkaline barrier slurry without any inhibitors for barrier CMP (chemical mechanical planarization) and investigated its CMP performance. The characteristics of removal rate and selectivity of Ti/SiO2/Cu were investigated under the same process conditions. The results obtained from 6.2 mm copper, titanium and silica show that copper has a low removal rate during barrier CMP by using this slurry, and Ti and SiO2 have high removal rate selectivity to Cu. Thus it may be helpful to modify the dishing. The TSV wafer results reveal that the alkaline barrier slurry has an obvious effect on surface topography correction, and can be applied in TSV barrier CME 相似文献