An investigation of carbon nanotube jet grinding

Since their observation in 1976 and 1991, carbon nanotubes (CNTs) have generated much interest due to their properties and potential applications. CNTs are tubular carbon molecules with remarkable mechanical, electrical, chemical and thermal properties, which make them useful in various applications. Industries producing CNTs via the fluidized bed chemical vapor deposition technique face challenges related to the size of CNT bundles. The two main challenges are agglomeration and agglomerate size distribution control. A solution to these challenges involves the use of jet mills to grind the CNT agglomerates. The goal of this study was to determine whether the nanotubes could be ground with air jets using a commercial jet mill and apply a two-parameter model to describe the grinding process. The present study has indicated that air-jet grinding of CNTs is feasible with a typical commercial jet mill. This paper presents the effect of operational parameters on the arithmetic mean diameter of the ground product. Sonic velocity through the grinding nozzles was required to obtain reasonable grinding rates and relatively narrow particle size distributions. This occurs at high air to solids feedrate ratios. Additionally, a simple attrition model can describe the grinding process in the spiral jet mill.     

Effect of spray nozzle design on liquid-solid contact in fluidized beds

In industrial fluid cokers the feedstock, consisting of heavy bituminous hydrocarbons, is atomized with steam and injected into a hot fluidized bed of coke. Good and uniform contact of the liquid droplets with the solid particles is required to provide heat for the cracking reactions while minimizing mass transfer effects. Experiments in a pilot plant coker have suggested that the initial particle/liquid mixing, in the spray jet, is rather poor. Experiments in a X-ray scanner showed that liquid droplets and entrained particles accumulate just below the tip of the jet plume to form agglomerates.An experimental technique was used to quantitatively determine the quality of mixing with a variety of nozzle configurations including several novel designs. By improving spray stability, redistributing liquid droplets to the solids-rich region of the jet and increasing the surface area of the gas-liquid jet-fluidized bed interface, liquid/solid contact is improved.     

Study of a downward gas jet in a two–dimensional fluidized bed

The study of a downward gas jet was performed in a two–dimensional (2–D) fluidized bed of sand particles under conditions of minimum fluidization and at atmospheric pressure and room temperature. The jet shifted through a cyclic sequence of left–central–right–central–left positions. The probability of the left and right jets was 40% each, while the less stable central jet occurred only 20% of the time. Discrete probability distributions of jet presence for each of the three jet configurations and an overall distribution are presented. They show that jets are dominant along the external walls of the nozzle. The depth of the downward jet increased with air flowrate in agreement with the correlation from Massimilla and Russo (1973).     

Ultrapyrolysis of automobile shredder residue

A fast pyrolysis (Ultrapyrolysis) process was employed to convert automobile shredder residue (ASR) into chemical products. Experiments were conducted at atmospheric pressure and temperatures between 700 and 850°C with residence times between 0.3 and 1.4 seconds. Pyrolysis products included 59 to 68 mass% solid residue, 13 to 23 mass% pyrolysis gas (dry) and 4 to 12 mass% pyrolytic water from a feed containing 39 mass% organic matter and 2 mass% moisture. No measurable amounts of liquid pyrolysis oil were produced. The five most abundant pyrolysis gases, in vol%, were CO (18–29), CO₂ (20–23), CH₄ (17–22), C₂H₄ (20–22) and C₃H₆ (1–11), accounting for more than 90% of the total volume. The use of a higher organic content ASR feed (58 mass%) resulted in less solid residue and more pyrolysis gas. However, no significant changes were noted in the composition of the pyrolysis gas.     

Mass transfer between solid particles and liquid in a three phase fluidized bed

Particle-liquid mass transfer in a co-current three-phase fluidized bed of glass beads, water and air was studied with two measurement techniques. Both techniques measured the weight loss of a few particles coated with benzoic acid in a bed of inert glass beads. The effects of liquid and gas velocities, gas distribution and surface active agents on particle-liquid mass transfer in a three-phase fluidized bed were thus determined. In the absence of surface active agents in the liquid, particle-liquid mass transfer rates in a three-phase fluidized bed were up to 30% higher than in the corresponding liquid fluidized bed. When surface active agents were added to the liquid, the particle-liquid mass transfer rate was increased by up to about 100% in the three-phase fluidized bed, relative to the liquid fluidized bed. The particle-liquid mass transfer coefficient was found to be inversely proportional to the liquid hold-up in the three-phase fluidized bed.     

Effect of curing and heat treatment history on the dynamic mechanical response and the pore structure of hardened cement paste

Results for the dynamic mechanical response of hcp (hardened cement paste) specimens as a function of the curing-heat treatment history are reported. The temperature range investigated is from ?160°C to +100°C. In the temperature range from +25°C to +100°C, specimens cured at room temperature (R-cured) show a partially irreversible transition (reduction) in E. There are two low temperature transitions: the “adsorbate transition” between ?160°C and ?6-°C, and the “capillary transition” between ?50°C and 0°C. Both of these transitions are significantly affected by the curing-heat treatment history. Furthermore, both the E-modulus and the BET (water) surface area decrease as the severity of heat treatment increases.     

Modeling and Analysis of UAV-Assisted Mobile Network with Imperfect Beam Alignment

With the rapid development of emerging 5G and beyond (B5G), Unmanned Aerial Vehicles (UAVs) are increasingly important to improve the performance of dense cellular networks. As a conventional metric, coverage probability has been widely studied in communication systems due to the increasing density of users and complexity of the heterogeneous environment. In recent years, stochastic geometry has attracted more attention as a mathematical tool for modeling mobile network systems. In this paper, an analytical approach to the coverage probability analysis of UAV-assisted cellular networks with imperfect beam alignment has been proposed. An assumption was considered that all users are distributed according to Poisson Cluster Process (PCP) around base stations, in particular, Thomas Cluster Process (TCP). Using this model, the impact of beam alignment errors on the coverage probability was investigated. Initially, the Probability Density Function (PDF) of directional antenna gain between the user and its serving base station was obtained. Then, association probability with each tier was achieved. A tractable expression was derived for coverage probability in both Line-of-Sight (LoS) and Non-Line-of-Sight (NLoS) condition links. Numerical results demonstrated that at low UAVs altitude, beam alignment errors significantly degrade coverage performance. Moreover, for a small cluster size, alignment errors do not necessarily affect the coverage performance.     

Experimental deformation analysis of an adhesively bonded multi-material joint for marine applications

The strength and deformation of full-scale adhesively bonded multi-material joints is studied in this paper. Four joints with a thick layer of methyl methacrylate adhesive (MMA) have been manufactured in shipyard conditions. In two specimens, cracks have been introduced at steel–adhesive and composite–adhesive interfaces. One cracked and one un-cracked specimen were subjected to quasi-static tensile testing; the two remaining specimens were stepwise loaded/unloaded with increasing load until failure. The strain in the adhesive layers was measured with digital image correlation (DIC). This showed a predominant shear deformation and dissimilar shear strain patterns for different bond lines. Fibre Bragg (FBG) sensors were used to monitor strains at steel and composite constituents and to detect the onset and evolution of damage in the un-cracked specimen. Strains measured by FBG sensors correspond well with DIC results at nearby regions. All specimens failed by delamination of the composite panel near the composite–adhesive interface.     

Transferrin-Decorated Niosomes with Integrated InP/ZnS Quantum Dots and Magnetic Iron Oxide Nanoparticles: Dual Targeting and Imaging of Glioma

The development of multifunctional nanoscale systems that can mediate efficient tumor targeting, together with high cellular internalization, is crucial for the diagnosis of glioma. The combination of imaging agents into one platform provides dual imaging and allows further surface modification with targeting ligands for specific glioma detection. Herein, transferrin (Tf)-decorated niosomes with integrated magnetic iron oxide nanoparticles (MIONs) and quantum dots (QDs) were formulated (PEGNIO/QDs/MIONs/Tf) for efficient imaging of glioma, supported by magnetic and active targeting. Transmission electron microscopy confirmed the complete co-encapsulation of MIONs and QDs in the niosomes. Flow cytometry analysis demonstrated enhanced cellular uptake of the niosomal formulation by glioma cells. In vitro imaging studies showed that PEGNIO/QDs/MIONs/Tf produces an obvious negative-contrast enhancement effect on glioma cells by magnetic resonance imaging (MRI) and also improved fluorescence intensity under fluorescence microscopy. This novel platform represents the first niosome-based system which combines magnetic nanoparticles and QDs, and has application potential in dual-targeted imaging of glioma.