Hydrogen annealing effect on DC and low-frequency noise characteristics in CMOS FinFETs

The hydrogen annealing process has been used to improve surface roughness of the Si-fin in CMOS FinFETs for the first time. Hydrogen annealing was performed after Si-fin etch and before gate oxidation. As a result, increased saturation current with a lowered threshold voltage and a decreased low-frequency noise level over the entire range of drain current have been attained. The low-frequency noise characteristics indicate that the oxide trap density is reduced by a factor of 3 due to annealing. These results suggest that hydrogen annealing is very effective for improving device performance and for attaining a high-quality surface of the etched Si-fin.     

Abnormal junction profile of silicided p+/n shallowjunctions: a leakage mechanism

The leakage mechanism in p⁺/n shallow junctions fabricated using Co silicidation and shallow trench isolation processes has been investigated using transmission electron microscopy (TEM) combined with selective chemical etching. TEM and TSUPREM-4 simulation results show that dopant profiles bend upward near the edge of the active region. The formation of the abnormal profile is attributed to transient enhanced diffusion induced by source/drain implantation. Based on the TEM and simulation results, it is suggested that the shallower junctions formed near the active edge can serve as a source for leakage current in the silicided p+ /n shallow junctions     

Facile modifications of polyimide via chloromethylation: II. Synthesis and characterization of thermocurable transparent polyimide having methylene acrylate side groups

From chloromethylated polyimide, a useful starting material for modification of aromatic polyimides, a thermocurable transparent polyimide having acrylate side groups was prepared. In the presence of 1,8‐diazabicyclo[5,4,0]undec‐7‐ene, chloromethylated polyimide was esterified with acrylic acid to synthesize poly(imide methylene acrylate). The polymer was soluble in organic solvent, which makes it possible to prepare a planar film by spin coating. The polymer film became insoluble after thermal treatment at 230 °C for 30 min. Optical transparency of the film at 400 nm (for 1 µm thickness) was higher than 98 % and not affected by further heating at 230 °C for 250 min. Adhesion properties measured by the ASTM D3359‐B method ranged from 4B to 5B. Preliminary results of planarization testing showed a high degree of planarization (DOP) value (>0.53). These properties demonstrate that poly(imide methylene acrylate) could be utilized as a thermocurable transparent material in fabricating display devices such as TFT‐LCD. Copyright © 2004 Society of Chemical Industry     

Holographic polymer‐dispersed liquid crystal fabrication under electric field

The transmission mode of holographic polymer‐dispersed liquid crystals (HPDLCs) was developed an under electric field. It is reported that orientation of LC molecules under an electric field induces orientation of oligomer molecules giving rise to low off‐state diffraction and small grating shrinkage. Copyright © 2005 Society of Chemical Industry     

Direct adaptive control of nonminimum phase systems using integralaction

A direct adaptive control scheme is proposed for nonminimum-phase systems in which controller parameters are estimated from the recursive least-squares algorithm and additional auxiliary parameters are obtained from the proposed polynomial identity. A local convergence is guaranteed without any extra condition. Integral action is incorporated into the adaptive controller to eliminate the steady-state error and to satisfy a condition of the unique solution for the polynomial identity. The control law used in this scheme is based on the set-point-on-I-only proportional-integral-derivative (PID) structure     

Onset of buoyancy-driven convection in melting from below

When a horizontal homogeneous solid is melted from below, convection can be induced in a thermally unstable melt layer. In this study the onset of buoyancy-driven convection during time-dependent melting is investigated by using similarly transformed disturbance equations. The critical Rayleigh numbers based on the melt-layer thickness are found numerically for various conditions. For small superheats, the present predictions approach the well known results of classical Rayleigh-Bénard problems, that is, critical Rayleigh numbers are located between 1,296 and 1,708, regardless of the Prandtl number. However, for high superheats the critical Rayleigh number increases with an increase in phase change rate but with decrease in Prandtl number.     

Finger assignment schemes for RAKE receivers with multiple-way soft handover

We propose and analyze new finger assignment techniques that are applicable for RAKE receivers in the soft handover (SHO) region. Specifically, extending the results for the case of two-base station (BS), we consider the multi-BS situation, attack the statistics of several correlated generalized selection combining (GSC) stages, and provide closed-form expressions for the statistics of the output signal-to-noise ratio (SNR). By investigating the tradeoff among the error performance, the average number of required path estimations/comparisons, and the SHO overhead, we show through numerical examples that the new schemes offer commensurate performance in comparison with more complicated GSC-based diversity systems while requiring a smaller estimation load and SHO overhead.     

Study on the c-axis preferred orientation of ZnO film on various metal electrodes

ZnO thin film was deposited on various metal electrodes by reactive sputtering, and c-axis preferred orientation of the film has been studied. ZnO, which has high piezoelectricity, is promising for oscillators or filter devices such as surface acoustic wave (SAW) device, gas sensor, and film bulk acoustic resonator (FBAR). But, for the application of ZnO film for these devices, the film should be grown with c-axis normal to the electrode. In this study, Pt, Al, and Au were deposited on Si wafer, and the surface roughness and crystal structure of the ZnO film on the electrode were investigated using AFM, scanning electron microscopy (SEM), and X-ray diffraction (XRD). Columnar structures of ZnO films were grown with c-axis normal to all electrodes, and among them Pt electrode showed the highest preferred orientation of ZnO film.     

A neural network-based power system stabilizer using power flowcharacteristics

A neural network-based power system stabilizer (neuro-PSS) is designed for a generator connected to a multi-machine power system utilizing the nonlinear power flow dynamics. The use of power flow dynamics provides a PSS for a wide range of operation with reduced size neural networks. The neuro-PSS consists of two neural networks: neuro-identifier and neuro-controller. The low-frequency oscillation is modeled by the neuro-identifier using the power flow dynamics, then a generalized backpropagation-through-time (GBTT) algorithm is developed to train the neuro-controller. The simulation results show that the neuro-PSS designed in this paper performs well with good damping in a wide operation range compared with the conventional PSS     

Compact Dipole Antenna for Terrestrial Digital Multimedia Broadcasting Service

A compact dipole antenna for the terrestrial digital multimedia broadcasting (TDMB) application is presented. The length of the antenna is about 0.06λ at the TDMB resonance frequency of 190 MHz. Miniaturization of the antenna is achieved by using meander structures and lumped elements. The proposed antenna has two resonance frequencies and covers the TDMB band from 174 MHz to 216 MHz in Korea. The antenna has good impedance bandwidth and radiation characteristics for the TDMB. The experimental results of the designed dipole antenna are presented and analyzed.