Ozone measurement in visible region: an optical fibre sensor system

Ozone measurement based on the optical absorption of visible light at 603 nm using polymer optical fibres is investigated and tested. Comparisons with a commercial UV based sensor demonstrate the ability of the visible based sensor to measure high concentrations over a range 27-127 mg/litre. A resolution of 5 mg/litre is also demonstrated for this sensor.     

Structural studies of TiN/ZrN multilayer coating deposited by physical vapour deposition

Multilayer coatings have been produced using unbalanced magnetron physical vapour deposition in which discrete layers of TiN and ZrN were co-deposited. It has been shown that the multilayers exhibited two-fold periodicity having values of 13 and 2.8 nm. This periodicity, measured both by cross-sectional transmission electron microscopy and low-angle X-ray diffraction, has been precisely related to the process parameters used. Analysis has shown that a third, previously unreported, phase existed within the coating having a lattice parameter comparable to that of TiN and a well-defined orientation relationship with the primary phases. The existence of this phase has been explained in terms of variations in the stoichometry of the coating due to non-uniform metal to nitrogen deposition rates within the chamber. Textural studies revealed that preferred orientation existed in the coating; the degree of which was greater in the ZrN layers than the TiN layers.     

A model for bilayer membrane electroporation based on resultant electromechanical stress

Reconsideration of the effect of an electrical field applied across a phospholipid bilayer membrane shows that, in addition to a compressive stress normal to the membrane plane, transverse traction stresses are generated in the lateral plane of the membrane. In the fields usually employed for electroporation these transverse stresses are likely to be sufficient to reduce the membrane tension considerably, causing electroporation and rupture. This mode of field-induced change in the membrane provides a natural model for the various forms of electroporation.     

A review of bacteriological culture of removed intrauterine contraceptive devices

The management of pain in patients with burn wounds is complex and problematic. Burn-wound pain is severe, inconsistent and underestimated. Patients experience severe pain, especially during procedures, until wound healing has occurred. A multi-modality approach is needed for effective management of pain, which requires an understanding of the mechanisms of pain. Altered pharmacokinetics and pharmacodynamics in burn-wound patients makes drug actions unpredictable. Opioids alone are seldom sufficient for pain control. The multi-modality approach includes the use of opioids and non-steroidal anti-inflammatory, anxiolytic and alternative drugs. Ketamine has been found to be a useful agent for analgesia in burn-wound patients; a dose of 10 mg/kg qid per os was found to be an effective adjunct to pain therapy.     

Extending trouble ticket systems to fault diagnostics

Network management in large heterogeneous communication environments requires the incorporation of more advanced tools than are currently available, especially in the area of fault management. By providing an informational infrastructure for documenting network behavior and maintenance activities, TTSs (trouble ticket systems) have provided some relief for the fault management problem. Researchers have recognized TTSs as a means for realizing more advanced functions in network management platforms to effect automatic trouble ticket generation, fault diagnostics, and the correlation of multiple views network problems and behavior. The authors describe current research trends towards understanding and implementing these advanced functions in a TTS framework     

Early detection of ageing in solder joints through laser probe thermal analysis of the peltier effect

We have recently developed an optical contactless method for testing the quality of solder joints during accelerated thermal cycling ageing processes.¹ The method was based upon the measurement of the dynamic thermal behaviour of the joint to short bursts of Joule heating. It has proved to be efficient in revealing the formation of cracks at the lead-solder interface. We present a method to evaluate ageing at a much earlier stage in the cycling process. We have observed in earlier work,¹ that before cracks appear, structural changes occur in the solder at the lead-solder interface. The thermal response of the solder joint is recorded over time to a Peltier heat perturbation produced by flowing a current pulse through the interface where structural changes occur. The key point in this method is to discriminate the Peltier effect from the Joule thermal response because both effects generate heat. The variation of the early Peltier response in the thermal cycling ageing tests is seen as a quantitative signature of the structural changes in the lead-solder interface.     

Cars, phones, and Tamagotchi tribes

As if life isn't already crowded enough with obligations, “Tamagotchis” (virtual pets) would seem to be at odds with the Information Age, but cars, phones and TV-like appliances will become more like Tamagotchis as the friction-free economy once again expresses itself in tribalism. My premise is simple: the friction-free economy rewards retro-cultures that yearn to return to agrarian tribalism. Selling hi-tech products in this new economy becomes ritual, and the greater the ritual, the greater the financial rewards. Some may use different names-database marketing, targeting or niche marketing-but the key to expanding the computer industry will be to build a tribe around your brand and flaunt it. Successful product design and sales will increasingly require targeting products, services and ideas to various tribes. An idea long understood in the entertainment and services industry, this is only now becoming a computer industry mantra. The question is, how will this impact the design of future computer products? Study the Tamagotchi and other Christmas season best-sellers to find out     

A mixed-signal RAM decision-feedback equalizer for disk drives

A mixed-signal RAM decision-feedback equalizer (DFE) that operates at 90 Mb/s is described. In the analog domain, the DFE subtracts intersymbol interference caused by the past four outputs. The equalized signal is fed into a nonuniform flash analog-to-digital converter (ADC) to produce the decision output and error signal used to adapt the RAM contents in the digital domain. With a 5 V supply voltage, the power dissipation is 260 mW during steady-state operation. The active area is 4.5 mm² in a 1 μm CMOS process     

Technique for Producing Mullite and Other Mixed-Oxide Systems

Mixed-oxide systems are of interest in a variety of technical ceramic applications. The key in many systems is to achieve a high degree of homogeneity, approaching the molecular level. A technique for producing mixed oxides via direct oxidation of mixtures of organometallic compounds is discussed as a potential route. Preliminary work performed on producing mullite is discussed.