Mammogram pectoral muscle removal and classification using histo-sigmoid based ROI clustering and SDNN

Multimedia Tools and Applications - Mammograms are the images used by radiologists to diagnose breast cancer. Breast cancer is one of the most common cancers in women. The early detection of breast...     

Modeling of Ignition and Combustion of a Coflowing Hydrogen Jet in a Supersonic Air Flow

Combustion, Explosion, and Shock Waves - Results of a numerical study of mixing, ignition, and combustion of a cold hydrogen jet propagating along the lower wall of a channel parallel to a...     

Modern Photodetector IR-Modules

Journal of Communications Technology and Electronics - In recent years, there has been a rapid improvement in photonics products due to the use of multilayer heterostructures grown on the basis of...     

Analysis of stepwise charging limits and its implementation for efficiency improvement in switched capacitor DC–DC converters

In this work we analysed the stepwise charging technique to find the limits from which it is beneficial in terms of load capacitance and charge–discharge frequency. We included in the analysis practical limitations such as the consumption of auxiliary logic needed to implement the technique and the minimum size of auxiliary switches imposed by the technology. We proposed an ultra-low-power logic block to push these limits and to obtain benefits from this technique in small capacitances. Finally, we proposed to use a stepwise driver in the driving of the gate capacitance of power switches in switched-capacitor (SC) DC–DC converters. We designed and manufactured, in a 130 nm process, a SC DC–DC converter and measured a 29% energy reduction in the gate-drive losses of the converter. This accounts for an improvement of 4% (from 69 to 73%) in the overall converter efficiency.

     

A Conversion Method for the Preparation of Calcium Formate

Theoretical Foundations of Chemical Engineering - Calcium formate is widely used in construction, tanning, and textile manufacture and as an E238 biological additive in cosmetology and the food...     

Evaluation of direct light processing for the fabrication of bioactive ceramic scaffolds: Effect of pore/strut size on manufacturability and mechanical performance

Bioactive ceramic scaffolds for bone regeneration consisting of a three-dimensional mesh of interpenetrating struts with square section were fabricated via Digital Light Processing (DLP). The ability of the technique to manufacture 3D porous structures from β-tricalcium phosphate (β-TCP) powders with different dimensions of struts and pores was evaluated, identifying the possibilities and limitations of the manufacturing process. Small pore sizes were found to seriously complicate the elimination of excess slurry from the scaffold’s innermost pores. The effect of the strut/pore size on the mechanical performance of the scaffolds under compressive stresses was also evaluated, but no significant influence was found. Under compressive stresses, the structures resulted weaker when tested perpendicularly to the printing plane due to interlayer shear failure. Interlayer superficial grooves are proposed as potential failure-controlling defects, which could also explain the lack of a Weibull size effect on the mechanical strength of the fabricated DLP scaffolds.     

Influence of Grain Structure Features on the Thermoelectric Properties of Compounds Based on Bismuth Telluride

Glass and Ceramics - An analysis of the specific mechanisms of the influence of the state of the grain structure on the thermoelectric properties (electrical resistivity and total thermal...     

A novel ceramic matrix composite based on YNbO4–TiO2 for microwave applications

This work presents the dielectric properties of YNbO₄ (YNO)–TiO₂ composites in the microwave range. X-ray diffraction analysis demonstrates that the addition of TiO₂ to YNO results in the formation of a Y(Nb_0.5Ti_0.5)₂O₆ phase. In the microwave range, the values of permittivity and dielectric loss did not present major changes with the increment of TiO₂. Moreover, the addition of TiO₂ results in an improvement in the thermal stability of YNO, with YNO63 demonstrating a resonant frequency of ?8.96 ppm.°C^?1. We utilised numerical simulations to evaluate the behaviour of these materials as dielectric resonator antennae and it is found that they exhibit a reflection coefficient below ?10 dB at the resonant frequency, with a realised gain of 4.94 – 5.76 dBi, a bandwidth of 665–1050 MHz and a radiation efficiency above 84%. Our results indicate that YNO–TiO₂ composites are interesting candidates for microwave operating devices.     

Two-step sinter-crystallization of K2O–CaO–P2O5–SiO2 (45S5-K) bioactive glass

Bioactive glasses and glass-ceramics (GCs) effectively regenerate bone tissue, however most GCs show improved mechanical properties. In this work, we developed and tested a rarely studied bioactive glass composition (24.4K₂O-26.9CaO-46.1SiO₂-2.6P₂O₅ mol%, identified as 45S5-K) with different particle sizes and heating rates to obtain a sintered GC that combines good fracture strength, low elastic modulus, and bioactivity. We analyzed the influence of the sintering processing conditions in the elastic modulus, Vickers microhardness, density, and crystal phase formation in the GC. The best GC shows improved properties compared with its parent glass. This glass achieves a good densification degree with a two-step viscous flow sintering approach and the resulting GC shows as high bioactivity as that of the standard 45S5 Bioglass®. Furthermore, the GC elastic modulus (56 GPa) is relatively low, minimizing stress shielding. Therefore, we unveiled the glass sintering behavior with concurrent crystallization of this complex bioactive glass composition and developed a potential GC for bone regeneration.