基于支持向量机的缓存预估模型的设计与实现

采用支持向量机(SVM)对网络业务流数据进行预测估计，通过训练样本，从而获得样本以外数据的分布规律。在此基础上，设计了一种网络排队队列缓存的预估模型。实验表明，该模型具有较高的训练效率和很高的估计精确度。     

磷钨酸乙醇染色法在嗜铬颗粒电镜X射线显微分析中的应用

通过比较常规透射电镜制样法、快速冷冻固定－冷冻超薄切片法及磷钨酸乙醇（EPTA）染色法在嗜铬颗粒透射电镜X射线显微分析中的应用，发现磷钨酸乙醇染色法能使嗜铬颗粒电子着色，从而较好地显示嗜铬颗粒的超微结构。同时磷钨酸乙醇染色法也以在一定程度上原位保留生物样品中元素，可以应用于检测样品元素含量的变化或比较样品元素含量的组间差别，提示磷钨酸乙醇染色法是一种可应用于透射电镜X射线显微分析的经济简便的生物样品制备方法。     

三水草酸铀酰的红外激光化学

文章研究了三水草酸铀酰(UO_2C_2O_4·3H_2O)在兆瓦脉冲二氧化碳激光辐照下的红外激光化学反应,它与草酸铀酰的热分解反应不同,反应产物是二氧化铀和二氧化碳。反应的量子效率随激光波长不同而变化。     

Microstructure and Mechanical Properties of Heat-treated GeSb_2Te_4 Thin Films

The effect of annealing on microstructure,adhesive and frictional properties of GeSb 2 Te 4 films were experimentally studied.The GeSb 2 Te 4 films were prepared by radio frequency(RF)magnetron sputtering,and annealed at 200℃and 340℃under vacuum circumstance,respectively.The adhesion and friction experiments were mainly conducted with a lateral force microscope(LFM)for the GeSb 2 Te 4 thin films before and after annealing.Their morphology and phase structure were analyzed by using atomic force microscopy(AFM)and X-ray Diffraction(XRD)techniques,and the nanoindention was employed to evaluate their hardness values.Moreover,an electric force microscope(EFM)was used to measure the surface potential. It is found that the deposited GeSb 2 Te 4 thin film undergoes an amorphous-to-fcc and fcc-to-hex structure transition;the adhesion has a weaker dependence on the surface roughness,but a certain correlation with the surface potential of GeSb 2 Te 4 thin films.And the friction behavior of GeSb 2 Te 4 thin films follows their adhesion behavior under a lower applied load.However,such a relation is replaced by the mechanical behavior when the load is relatively higher.Moreover,the GeSb 2 Te 4 thin film annealed at 340℃presents a lubricative property.     

GPRS无线DDN系统与应用

介绍基于GPRS网络无线DDN系统的构成、组网以及在电力系统的应用，同时对传输包长度、效率、时延等参数进行分析。     

稠油油藏的注汽量预测

利用HCZ预测模型，可对已开发油田的年产量和累计产量进行全程预测，并且在实际应用中取得了较好的预测结果。本文结合稠油田的实际情况，推导出HXZ预测模型在热采中注汽参数的预测公式。结合曙光油田曙1－7－5块的开发数据进行了预测，效果较好。     

工程结构优化设计发展综述

 着重评述了工程结构优化设计研究领域从最初的尺寸优化发展到形状优化、拓扑优化的基本历程及其相关特点，并对优化设计选用的优化算法进行了归类，提出了这一领域今后仍然有待于发展的主要方面．     

石油系油浆与煤系闪蒸油的焦化性能——I．热解条件的影响

通过偏光显微镜观察了石油系油浆（LH）与煤系闪蒸油（SN）焦化后所得焦块的光学结构。结果表明，在较宽条件下两种原料单独焦化均得不到取向度高的流线型结构。将两种原料以一定比例混合后先热解丙焦化所得焦块的光学结构明显好于二者混合后直接焦化所得焦块的光学结构，其中LH和SN以3：2的重量比混合后在440℃、1MPa下热解3．5h然后再在530℃、1MPa下焦化8h所得焦块为具有较高取向度的流线型结构，适合于作为针状焦的起始原料。     

Preparation of a pitch-based activated carbon with a high specific surface area

Pitch based activated carbons (PAC) with a high specific surface area were produced by a direct chemical activation route in which oxidative stabilized pitch derived from ethylene tar oil was reacted with potassium hydroxide under various activation conditions. It was found that PACs with a surface area of around 2600–3600 m² g^-1 could be obtained under suitable activation conditions. N₂ adsorption (at 77 K) and X-ray photoelectron spectroscopy experiments showed that the PAC has a uniformly developed micropore structure and a narrow pore size distribution (radius 0.8–1.6 nm). Abundant oxygen-containing functional groups (such as C–OH, C–O–C, C=O, COOR etc.) were found to exist on its surface. Compared with a commercially available activated carbon (AC) and also a pitch based activated carbon fibre, PAC has a quicker adsorption–desorption velocity and a larger adsorptive capacity to benzene due to its higher surface area. Clear surface differences between PAC and AC were observed by transmission electron microscopy. This revised version was published online in November 2006 with corrections to the Cover Date.     

铅酸蓄电池的清洁生产

就中国铅酸蓄电池工业的可持续性发展与清洁生产问题进行了初步探讨,并就蓄电池正负极板水洗的清洁生产实例进行了介绍。