Impulse breakdown voltages of triggered multistage vacuum gap

Several sealed-off triggered vacuum gaps are connected in series to improve hold-off voltage. The characteristics of impulse breakdown voltage of these series-connected gaps are investigated experimentally. The sum hold-off voltage of series-connected gaps decreases to a unit hold-off voltage when the maximum value of voltage division ratio across the gaps increases to unity. Self-breakdown probability of the series-connected gaps is always higher than that of a single gap under the same conditions. Hence, stage efficiency of the multistage gap decreases with increasing number of stages. Its value is 90 percent with 2-stage gap and 75 percent with 5-stage gap, respectively, under the same voltage division ratio and the same gap length (2.0 mm) in each stage. Triggered breakdown voltage of 2- or 3- stage gap is several hundred volts when all gaps are triggered simultaneously at the peak of the main impulse wave and a working voltage range is nearly 100 percent in this case. The working voltage range decreases with number of stages. Its value is 45 percent with 3-stage gap and 15 percent with 5-stage gap, respectively, when one triggered gap is fired for switching.     

Circulation rates of boiling liquids in a vertical tube

An experimental study of heat transfer to boiling liquids under natural convective flow has been carried out in a single tube vertical thermosiphon reboiler to investigate the effect of heat flux and submergence on circulation rates. The test liquids used were distilled water, various concentrations of propan-2-ol in water and their azeotrope. The test section was an electrically heated stainless steel tube of 25.56 mm i.d., 28.85 mm o.d. and 1900 mm long with twenty-one spot welded copper constantan thermocouples to measure the variations in wall temperature along its axis. The uniform heat fluxes in the range of 3.5–42.4 kW/m² were employed while inlet liquid sub-cooling varied from 0.2 to 30.7 °C. The liquid submergence levels were maintained in the range 30–100%. The typical experimental data has been graphically presented and discussed. An empirical correlation has been developed from the experimental data of the present study through regression analysis.     

N-Type Field-Effect Transistors Using Multiple Mg-Doped ZnO Nanorods

Nanorod field-effect transistors (FETs) that use multiple Mg-doped ZnO nanorods and a SiO₂ gate insulator were fabricated and characterized. The use of multiple nanorods provides higher on-currents without significant degradation in threshold voltage shift and subthreshold slopes. It has been observed that the on-currents of the multiple ZnO nanorod FETs increase approximately linearly with the number of nanorods, with on-currents of ~1 muA per nanorod and little change in off-current (~4times10^-12). The subthreshold slopes and on-off ratios typically improve as the number of nanorods within the device channel is increased, reflecting good uniformity of properties from nanorod to nanorod. It is expected that Mg dopants contribute to high n-type semiconductor characteristics during ZnO nanorod growth. For comparison, nonintentionally doped ZnO nanorod FETs are fabricated, and show low conductivity to compare with Mg-doped ZnO nanorods. In addition, temperature-dependent current-voltage characteristics of single ZnO nanorod FETs indicate that the activation energy of the drain current is very low (0.05-0.16 eV) at gate voltages both above and below threshold     

Recursive solution technique in a multi-server bi-level queueingsystem with server breakdowns

The authors present a multiserver, first-come first-served queuing system that alternates between two modes of system operation. In one mode, all s servers are available, and in the other mode, only s-1 servers are available for serving the customers. This is due to breakdown of one of the servers. The random variables representing the system with s servers and s-1 servers have exponential distributions. In such a system, the steady-state birth/death equations are coupled because of the two modes of operation. A recursive solution is presented for computing the steady-state probabilities of such a system. Once these probabilities are known, the performance measures of interest can be easily obtained. Two practical examples validate the results and show the utility of this method. A distinct advantage of the recursive technique is that it is much faster and requires much less memory than the existing nonrecursive techniques. In a bilevel situation, the system performance measures are always bounded by two independent queuing systems with s and s-1 servers. A procedure has been outlined for extension to multiple modes of system operation     

SO2 SCRUBBING BY ULTRAFINE CA(OH)2 AEROSOL

The objective of the present study was to generate submicrometer calcium hydroxide aerosols and to investigate the effectiveness of such aerosols in sulfur capture. The effectiveness of SO₂ removal by Ca(OH)₂ aerosol has been investigated in an isothermal reactor. Ca(OH) ₂ aerosol was generated by a novel fluidizer system in which submicrometer-sized powders were entrained in gases. SO₂ was added to this aerosol to a concentration of 2000 ppm. The aerosol-SO₂ mixture was heated to 550°C-750°C in an isothermal tube reactor. The SO₂ removal efficiency, which varied from 20% to 70%, was determined to be a function of the aerosol concentration, reactor temperature and residence time. The fraction of aerosol reacted was not affected strongly by the aerosol concentration. The reaction kinetics were determined from the experimental data using a simple analytical model in which the rate is first order in both SO₂ and calcium hydroxide aerosol concentrations.     

Factors influencing the modulus of rupture of sulfur-infiltrated concrete

The experimental results presented in this paper indicate that the cement/aggregate ratio, the water/cement ratio, the size of aggregate, and the rate of cooling have significant influence on the modulus of rupture of sulfur-infiltrated concrete (SIC). Using sand only as aggregate and 65% cement, SIC of over 3500 psi in flexural tension was obtained from the test of 1″ × 1″ × 4″ specimens.     

Effect of structure on the thermal behaviour of ethynyl-terminated imide resins

A series of ethynyl-terminated aromatic imide monomers containing phosphine oxide in the backbone were synthesized by the reaction of tris(3-aminophenyl) phosphine oxide (TAP) or bis(3-aminophenyl)methyl phosphine oxide (BAP) with pyromellitic dianhydride (PMDA) or 3, 3′,4, 4′-benzophenone tetracarboxylic acid dianhydride (BTDA) or 4, 4′-perfluoroisopropylidenebis(phthalic anhydride), and 3-ethynyl aniline. Structural characterization was done by infrared, nuclear magnetic resonance spectroscopy and elemental analysis. Thermal characterization was done by differential scanning calorimetry and thermogravimetric analysis. The decomposition temperatures of cured resins were above 500°C in nitrogen atmosphere. Char yield at 800°C ranged from 52–63.5%.     

Summarizing consumer reviews

Journal of Intelligent Information Systems - E-commerce giants like Amazon rely on consumer reviews to allow buyers to inform other potential buyers about a product’s pros and cons. While...     

Numerical method using cubic B-spline for the heat and wave equation

In the present paper, the cubic B-splines method is considered for solving one-dimensional heat and wave equations. A typical finite difference approach had been used to discretize the time derivative while the cubic B-spline is applied as an interpolation function in the space dimension. The accuracy of the method for both equations is discussed. The efficiency of the method is illustrated by some test problems. The numerical results are found to be in good agreement with the exact solution.