Selective solvation of polystyrene in tetralin/cyclohexane mixtures

Refractive index increments and density increments have been measured at 307.6K for polystyrene in binary solvents of 1,2,3,4-tetrahydronaphthalene (tetralin, TET) and cyclohexane over the whole range of solvent composition. Comparison of these increments with the corresponding values obtained at dialysis equilibrium (i.e. at constant chemical potential of low molecular weight species) yielded the coefficients of selective adsorption (γ₁) of TET by the polymer. Positive values of γ₁ were exhibited at solvent compositions up to 78% (v/v) of the thermodynamically better solvent, TET. Theoretical curves of γ₁ vs. composition were calculated on the basis of, firstly, relevant interaction parameters and, secondly, interaction parameters in conjunction with solubility parameters. Both procedures afforded self-consistent results, which were, however, uniformly lower than the experimental values of γ₁.     

Effect of Al<Subscript>2</Subscript>O<Subscript>3</Subscript> particles on the microstructure and sliding wear of 7075 Al alloy manufactured by squeeze casting method

Aluminum (Al) alloy 7075 reinforced with Al₂O₃ particles was prepared using the stir casting method. The microstructure of the cast composites showed some degree of porosity and sites of Al₂O₃ particle clustering, especially at high-volume fractions of Al₂O₃ particles. Different squeeze pressures (25 and 50 MPa) were applied to the cast composite during solidification to reduce porosity and particle clusters. Microstructure examinations of the squeeze cast composites showed remarkable grain refining compared with that of the matrix alloy. As the volume fraction of particles and applied squeeze pressure increased, the hardness linearly increased. This increase was related to the modified structure and the decrease in the porosity. The effect of particle volume fraction and squeeze pressure on the dry-sliding wear of the composites was studied. Experiments were performed at 10, 30, and 50 N with a sliding speed of 1 m/s using a pin-on-ring apparatus. Increasing the particle volume fraction and squeeze pressure improved the wear resistance of the composite compared with that of the monolithic alloy, because the Al₂O₃ particles acted as load-bearing constituents. Also, these results can be attributed to the fact that the application of squeeze pressure during solidification led to a reduction in the porosity, and an increase in the solidification rate, leading to a finer structure. Moreover, the application of squeeze pressure improved the interface strength between the matrix and Al₂O₃ particles by elimination of the porosity at the interface, thereby providing better mechanical locking.     

Effects of including a quantitative trait locus in selection under different waiting plans of young bulls

The advantage of using the genotype of a quantitative trait locus (QTL) in selection schemes of dairy cattle was quantified using stochastic simulation. Three selection plans were studied. In the first plan, young bulls waited for 3 yr until their sisters completed a lactation and then were evaluated and selected based on an animal model. In a second plan, young bulls waited for 5 yr until their daughters completed a lactation. An intermediate 4-yr waiting plan was also studied. Simulation was for 16 yr with overlapping generations. Population and model parameters were proportional to the U.S. Holstein population. The advantage of using a QTL was quantified as the percentage of superiority of QTL-assisted over QTL-free selection using cumulative genetic response. Percentage of superiority was reported for four selection pathways: active sires, young bulls, bull dams, and first lactation cows. A general trend was observed: low superiority in early years of selection that increased to a plateau in later years and then decreased. The superiority of the QTL information was greatest in the 3-yr waiting plan and least in the 4-yr waiting plan. Superiority at plateau for selection pathways ranged from 16 to 26% for the 3-yr waiting plan, from 3 to 12% for the 4-yr waiting plan, and from 5 to 13% for the 5-yr waiting plan. The contribution to selection response attributed to the QTL and the polygenes was quantified. The rate at which the favorable allele approached fixation and the accuracy of predicting breeding values on the percentage of superiority were studied.     

Genetic basis and risk factors for infectious and noninfectious diseases in US Holsteins. I. Estimation of genetic parameters for single diseases and general health

Health data collected from 1996 to 1999 from 177 herds in Minnesota and Wisconsin were analyzed to establish genetic basis for infectious and noninfectious diseases. Three types of health traits were targeted. First, available infectious conditions were used to identify animals that are superior in their general immunity (including innate immunity) for infectious diseases. Generalized immunity may be thought of as a combination of immune responses to a variety of immune system challenges. Second, single infectious and noninfectious diseases were analyzed separately. Third, infectious reproductive diseases as one category of related conditions, and cystic ovary disease as one category of 3 related noninfectious ovary disorders were studied.Data were analyzed using a threshold model that included herd, calving year, season of calving, and parity as cross-classified fixed factors; and sire and cow within sires as random effects. Days at risk and days in milk at the beginning of a record were included by fitting the days as continuous covariates in the model. A heritability value of 0.202 +/- 0.083 was estimated for generalized immunity. Heritability values of 0.141 and 0.161 were estimated for uterine infection and mastitis, respectively. Heritability of single noninfectious disorders ranged from 0.087 to 0.349. The amount of additive genetic variance recovered in the underlying scale of noninfectious disorders tended to zero when combining multiple conditions. The study supports combining infectious diseases into categories of interest but we do not recommend the same approach for noninfectious disorders.     

Dual growth of graphene nanoplatelets and carbon nanotubes hybrid structure via chemical vapor deposition of methane over Fe–MgO catalysts

Abstract

In this study, Fe–MgO catalyst substrates with various Fe and MgO combinations were evaluated for the growth of different types of carbon nanostructure materials (CNMs), particularly graphene nanoplatelets (GNPs) and carbon nanotubes (CNTs) via chemical vapor deposition using methane as a carbon source. The hydrogen yield was also determined as a valuable by-product in this process. Therefore, a set of Fe–MgO catalysts with different iron loadings (30, 80, 85, 90 and 100?wt %) were prepared by the combustion method to realize this target. The physicochemical properties of freshly calcined Fe–MgO catalysts were investigated by XRD, TPR and BET, while the as-grown CNMs were studied by HR-TEM, XRD and Raman spectroscopy. The results verified that the morphology of as-grown CNMs as well as the H₂ yield was directly correlated to the iron content in the catalyst composition. The XRD and TPR results showed that various FeMgO_x species with deferent levels of interactions were produced with the gradual incorporation of MgO content. TEM images indicated that GNPs were individually grown on the surface of high loaded iron-containing catalysts (90–100?wt %) due to the presence of highly aggregated iron particles. While multi-walled carbon nanotubes (MWCNTs) with uniform diameters were grown on the low iron-loaded catalyst (30%Fe/MgO) due to the formation of highly dispersed FeMgO_x particles. On the other hand, GNPs/MWCNTs hybrid materials were grown on the surface of 80%Fe and 85%Fe/MgO catalysts. This behavior can be interpreted by the co-existence of highly aggregated and highly dispersed Fe₂O₃ particles in the catalyst matrix. The results demonstrated that the catalyst composition has a notable effect on the nature of CNMs products and H₂ yield.     

A Robust Wearable Point-of-Care CNT-Based Strain Sensor for Wirelessly Monitoring Throat-Related Illnesses

Point-of-care testing (POC) has the ability to detect chronic and infectious diseases early or at the time of occurrence and provide a state-of-the-art personalized healthcare system. Recently, wearable and flexible sensors have been employed to analyze sweat, glucose, blood, and human skin conditions. However, a flexible sensing system that allows for the real-time monitoring of throat-related illnesses, such as salivary parotid gland swelling caused by flu and mumps, is necessary. Here, for the first time, a wearable, highly flexible, and stretchable piezoresistive sensing patch based on carbon nanotubes (CNTs) is reported, which can record muscle expansion or relaxation in real-time, and thus act as a next-generation POC sensor. The patch offers an excellent gauge factor for in-plane stretching and spatial expansion with low hysteresis. The actual extent of muscle expansion is calculated and the gauge factor for applications entailing volumetric deformations is redefined. Additionally, a bluetooth-low-energy system that tracks muscle activity in real-time and transmits the output signals wirelessly to a smartphone app is utilized. Numerical calculations verify that the low stress and strain lead to excellent mechanical reliability and repeatability. Finally, a dummy muscle is inflated using a pneumatic-based actuator to demonstrate the application of the affixed wearable next-generation POC sensor.     

Genetic impacts of using female-sorted semen in commercial and nucleus herds

This study was designed to investigate the genetic effects of using sorted semen in a dairy cattle population. Progress was monitored in elite and commercial animals over 20 yr of selection. To study the genetic impact of using sorted semen in commercial herds, a scenario was evaluated in which female-sorted semen was available to commercial herds. Second, to study the genetic impact of using sorted semen in nucleus herds, scenarios were simulated in which female-sorted semen was used only in a centralized nucleus herd, in which multiple ovulation and embryo transfer (MOET) took place. Because of the additional advantage of marker-assisted selection when sorted semen was used in nucleus herds, a second scenario was simulated in which both sorted semen and marker-assisted selection were implemented. In the scenario in which female-sorted semen was used in commercial herds, a large genetic advantage was observed early in commercial cows. The average superiority in first-lactation cows exceeded 30% in yr 11, relative to a base scheme with regular semen, but continued to decrease until it reached 9% in yr 20. The increased selection intensity in commercial cows contributed to the genetic merit of future cows (cow-to-cow contribution), but the contribution of the nucleus grew over time and gradually marginalized the cow-to-cow contribution. The genetic advantage of gender control in MOET schemes was minimal except when marker-assisted selection was also available. Two factors that affected the contribution of marker-assisted selection were studied: 1) within- vs. across-family selection of donors, and 2) the number of loci in the quantitative trait locus component. Schemes that selected donors regardless of their family structure were superior, and the quantitative trait locus component with more loci increased the effectiveness of sorted semen. Finally, we studied a reduced MOET scheme in which the number of harvested females was reduced from 42 to 25/yr. The reduced scheme in combination with female-sorted semen was not found to be genetically inferior to the large scheme in combination with regular semen.     

Overcoming Microenvironment-Mediated Chemoprotection through Stromal Galectin-3 Inhibition in Acute Lymphoblastic Leukemia

Environmentally-mediated drug resistance in B-cell precursor acute lymphoblastic leukemia (BCP-ALL) significantly contributes to relapse. Stromal cells in the bone marrow environment protect leukemia cells by secretion of chemokines as cues for BCP-ALL migration towards, and adhesion to, stroma. Stromal cells and BCP-ALL cells communicate through stromal galectin-3. Here, we investigated the significance of stromal galectin-3 to BCP-ALL cells. We used CRISPR/Cas9 genome editing to ablate galectin-3 in stromal cells and found that galectin-3 is dispensable for steady-state BCP-ALL proliferation and viability. However, efficient leukemia migration and adhesion to stromal cells are significantly dependent on stromal galectin-3. Importantly, the loss of stromal galectin-3 production sensitized BCP-ALL cells to conventional chemotherapy. We therefore tested novel carbohydrate-based small molecule compounds (Cpd14 and Cpd17) with high specificity for galectin-3. Consistent with results obtained using galectin-3-knockout stromal cells, treatment of stromal-BCP-ALL co-cultures inhibited BCP-ALL migration and adhesion. Moreover, these compounds induced anti-leukemic responses in BCP-ALL cells, including a dose-dependent reduction of viability and proliferation, the induction of apoptosis and, importantly, the inhibition of drug resistance. Collectively, these findings indicate galectin-3 regulates BCP-ALL cell responses to chemotherapy through the interactions between leukemia cells and the stroma, and show that a combination of galectin-3 inhibition with conventional drugs can sensitize the leukemia cells to chemotherapy.     

Comparative studies of some local oil seeds and seed cakes

A survey on the chemical constituents (protein, fat, carbohydrates, ash, fibre, calcium, phosphorus, iron) of 4 seeds and their cakes was done. These seeds are safflower seed (Carthamus tinctorius variety Giza 1), sunflower seeds (Helianthus annuus variety Giza 1), linseeds (Linum usitatissimum variety Giza 4) and imported rape seeds (Brassica napus Erglue). Caloric value of these seeds and seed cakes was calculated, PER, NPR and NPU were determined. No great variation was found with respect to the moisture content. The 4 seeds are rich in protein and fat. The ash content varies from (5.11 ± 0.26)% to (3.17 ± 0.13)%. The fiber content was low in both safflower and sunflower seeds and higher in both linseeds and rape seeds. The caloric values of the different seeds were very close. The seeds were found to be rich in phosphorus and low in calcium and contain considerable amounts of iron. The average PER values were 1.51, 1.61, 1.59, 1.84 and 2.50 for safflower seed cake, sunflower seed cake, linseed cake, rape seed cake and casein diet respectively. The average NPR was 3.11, 2.84, 2.84, 3.05 and 3.53 for safflower seed cake, sunflower seed cake, linseed cake, rape seed cake and casein respectively. The NPU values of the seed meals were 48.5, 49.3, 47.4 and 93.6 compared with 67.8 for casein. Using the different criteria (PER, NPR and NPU), it was clear that the protein quality of sunflower seed is very close to that of the linseed. Comparing the protein quality of safflower seed with those of both sunflower and linseed, NPU was in the same range, while PER was somewhat lower and NPR was higher than those of safflower and sunflower seed.     

Correlations among body condition scores from various sources, dairy form, and cow health from the United States and Denmark

The objectives of this study were to estimate genetic correlations among body condition scores (BCS) from various sources, dairy form, and measures of cow health. Body condition score and dairy form evaluated during routine type appraisal was obtained from the Holstein Association USA, Inc. A second set of BCS was obtained from Dairy Records Managements Systems (DRMS) and was recorded by producers that use PCDART dairy management software. Disease observations were obtained from recorded veterinarian treatments in several dairy herds in the United States. Estimated breeding values for diseases in Denmark were also obtained. Genetic correlations among BCS, dairy form, and cow health traits in the United States were generated with sire models. Models included fixed effects for age, DIM, and contemporary group. Random effects included sire, permanent environment, herd-year season for health traits, and error. Predicted transmitting abilities (PTA) for BCS and dairy form were correlated with estimated breeding values for disease in Denmark. The genetic correlation estimate between BCS from DRMS and BCS from the Holstein Association USA, Inc., was 0.85. The genetic correlation estimate between BCS and a composite of all diseases in the United States was -0.79, and PTA for BCS was favorably correlated with an index of resistance to disease other than mastitis in Denmark (0.27). Dairy form was positively correlated with a composite of all diseases in the United States (0.85) and was unfavorably correlated with an index for resistance to disease other than mastitis in Denmark (-0.29). Adjustment for protein yield PTA had a minimal affect on correlations between PTA for BCS or dairy form and disease in Denmark. Selection for higher body condition or lower dairy form with continued selection for yield may slow deterioration in cow health as a correlated response to selection for increased yield.