Which vessel is more important in the supercharged flap--artery, vein, or both? An experimental study

The supercharged flap is one which is expected to attain better survival, by anastomosing the distal vessels of the flap to the recipient vessels. An experimental study is reported to determine whether the vessel to be anastomosed should be an artery, a vein, or both. The authors advise anastomosing an artery and a vein, but they believe that arterial inflow is more important than venous drainage.     

Thermal response in thermal energy storage material around heat transfer tubes: effect of additives on heat transfer rates

The effects of carbon-fiber chips and carbon brushes as additives on the thermal conductivity enhancement of phase change materials (PCMs) using in latent heat thermal energy storage are investigated experimentally and numerically by considering the wall effect of the additives. The carbon-fiber chips are effective for improving the heat transfer rate in PCMs. However, the thermal resistance near the heat transfer surface is higher than that for the carbon brushes. As a result, the overall heat transfer rate for the fiber chips is lower than that for the carbon brushes. Consequently, the carbon brushes are superior to the fiber chips for the thermal conductivity enhancement under the present experimental conditions. The carbon brushes are moreover applied to the packed beds of particles to overcome their low thermal conductivity in chemical heat pump/storage. The carbon brushes essentially improve the heat transfer characteristics in the packed beds, though the thermal resistance is observed because the particles obstruct contact between the fibers and the heat transfer surfaces.     

Non-linear current–voltage characteristics related to native defects in SrTiO3 and ZnO bicrystals

SrTiO₃ and ZnO bicrystals with various types of boundaries were fabricated in order to examine their current–voltage characteristics across single grain boundaries. Their grain boundary structures were also investigated by high-resolution transmission electron microscopy. In Nb-doped SrTiO₃, electron transport behaviors depend on the type of boundaries. Random type boundaries exhibit highly non-linear current–voltage characteristics, while low angle boundaries show a slight non-linearity. On the contrary, undoped ZnO does not exhibit non-linear current–voltage characteristics in any type of boundaries including random ones. It is suggested that the differences observed in current–voltage properties between the two systems are mainly due to the difference in the accumulation behavior of acceptor-like native defects at grain boundaries. A clear non-linearity is obtained by means of Co-doping even for the highly coherent Σ1 boundary in a ZnO bicrystal. This is considered to result from the production of acceptor-like native defects by Co-doping.     

Micro-computerized tomographic observation of the spinning apparatus in Bombyx mori silkworms

Silkworms and spiders have evolved complex spinning apparatus thought to use highly controlled conditions to optimize protein folding and crystallization to provide a tough fiber. Accordingly, the structure and function of the natural spinning apparatus has been studied with great attention as an interesting piece of biological engineering with potential for mimicry in an industrial process. However it is still not well understood. Here we used Micro-Computerized Tomographic equipment (mCT) to visualize the three-dimensional structure of the spinning apparatus in Bombyx mori silkworms. Multidirectional tomograms obtained by X-ray radioscopy provided valuable information on the detailed arrangement of each muscle of the silk press. It is suggested that the duct in the silk press part plays a part as an extrusion die whose cross-sectional area can be controlled by muscles to optimize applied stresses in the partially gelled silk within its lumen.     

Accelerator Analysis of Tributyltin Adsorbed onto the Surface of a Tributyltin Resistant Marine Pseudoalteromonas sp. Cell

Tributyltin (TBT) released into seawater from ship hulls is a stable marine pollutant and obviously remains in marine environments. We isolated a TBT resistant marine Pseudoalteromonas sp. TBT1 from sediment of a ship’s ballast water. The isolate (10^{9.3 ± 0.2} colony-forming units mL⁻¹) adsorbed TBT in proportion to the concentrations of TBTCl externally added up to 3 mM, where the number of TBT adsorbed by a single cell was estimated to be 10^8.2. The value was reduced to about one-fifth when the lysozyme-treated cells were used. The surface of ethanol treated cells became rough, but the capacity of TBT adsorption was the same as that for native cells. These results indicate that the function of the cell surface, rather than that structure, plays an important role to the adsorption of TBT. The adsorption state of TBT seems to be multi-layer when the number of more than 10^6.8 TBT molecules is adsorbed by a single cell.     

The reaction of polypropylene with maleic anhydride

An addition reaction of maleic anhydride with polypropylene takes place in the presence of radical reagents or sunlight. The initial rate of the reaction was proportional to the concentration of polypropylene and maleic anhydride, and one-half power of the concentration of the radical reagents. The increase in the temperature from 80 to 120°C increased the rate of the reaction and di-cumyl peroxide was effective as a radical reagent for this reaction. Ionic crosslinked rubber-like polymers were obtained from the reaction of maleic polypropylene with some alkali metal compounds. They showed the characteristic absorption band due to ? COO^? in their infrared spectra.     

Polymerization of methyl methacrylate by tri-n-butylborane in the presence of amino acid esters

The polymerization of methyl methacrylate by tri-n-butylborane in the presence of amino acid esters was investigated. The binary systems of tri-n-butylborane and amino esters were found to be more effective for initiating the polymerization than tri-n-butylborane alone. Co-catalytic effects of amino acid esters were in the order: tyrosinate > glutamate > aspartate ? phenyl alaninate > serinate > glycinate. The rate of polymerization in a mixture of dimethylsulphoxide and toluene was proportional to the square root of the concentration of the initiator system, to the monomer concentration, and to the concentration of dimethylsulphoxide in the solvent. The overall energy of activation was estimated to be 4.6 kcal/mol for the tri-n-butylborane/methyl tyrosinate system. Copolymerization curves gave a typical free-radical character.