Isolation of antimicrobial agent from the marine algae Cystoseira hakodatensis

Cystoseira hakodatensis is an unutilised brown algae belonging to family Sargassaceae. A crude methanol extract from the algae showed inhibitory effects on the growths of Bacillus cereus and Bacillus licheniformis. To isolate the major antimicrobial agent, a sequential active‐guided isolation procedure was applied: liquid–liquid extraction, column chromatography and bio‐autography. A marked antimicrobial agent (active α) was isolated in hydrophobic fraction and was determined to phenolics without carbohydrates and proteins by phytochemical test. Regarding the antimicrobial potential, the isolated active α showed better inhibitory effects against B. cereus and B. licheniformis at 2 and 4 times of lower concentrations (62.5 and 31.3 μg mL^?1) in comparison with epigallocatechin gallate. These results showed that C. hakodatensis is a potential source of antimicrobial agent capable of preventing the growth of the two bacteria.     

Operation of superconducting fault current limiter using vacuum interrupter driven by electromagnetic repulsion force for commutating switch

Using conventional high‐temperature superconducting wire, a model superconducting fault current limiter (SFCL) is made and tested. Solenoid coil using Bi2223 silver sheath wire is so made that inductance is as small as possible and a vacuum interrupter is connected in series to it. A conventional reactor coil is connected in parallel. When the fault current flows in this equipment, superconducting wire is quenched and current is transferred into the parallel coil because of voltage drop of superconducting wire. This large current in parallel coil actuates magnetic repulsion mechanism of vacuum interrupter. Due to opening of vacuum interrupter, the current in superconducting wire is broken. By using this equipment, current flow time in superconducting wire can be easily minimized. On the other hand, the fault current is also easily limited by large reactance of parallel coil. © 2008 Wiley Periodicals, Inc. Electr Eng Jpn, 164(1): 52–61, 2008; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20315     

A numerical study of radiation heat transfer in sodium pool combustion and response surface modeling of luminous flame emissivity

A response surface model of the luminous flame emissivity of sodium pool fire has been proposed for use in safety analysis computer codes of a liquid metal fast reactor. The liquid sodium burns in air resulting in not only heat generation but also release of sodium oxide aerosols of sub-micron diameters. Aerosols levitating in air are radiative and they influence the allocation of combustion heat from the flame to atmospheric gas or sodium pool. The emissivity of the flame needs to be quantified, as it is one of user-specified parameters of the computer codes for the sodium fire analysis. The response surface model of the flame emissivity is developed based on numerical experiments on the physics of mass and heat transfer and behavior of the aerosol. Thermal-hydraulic equations have been solved coupled with aerosol dynamics and chemical reaction. Three influential variables on the emissivity are identified as pool temperature, gas temperature and oxygen molar fraction in the air. It has been found that the emissivity is calculated reasonably as a function of the three variables. The proposed response surface model can be easily employed in the sodium fire analysis codes because it is a simple quadratic expression. For the safety evaluation of the sodium fire, combined use is recommended of the proposed model and the lumped-mass zone model code.     

Use of a YAP1 overexpression cassette conferring specific resistance to cerulenin and cycloheximide as an efficient selectable marker in the yeast Saccharomyces cerevisiae.

Drug-resistance markers for yeast transformation are useful because they can be applied to strains without auxotrophic mutations. However, they are susceptible to technical difficulties, namely lower transformation efficiency and the appearance of drug-resistant mutants without the marker. To avoid these problems, we have constructed a phosphoglycerate kinase (PGK) promoter-driven YAP1 expression cassette, called PGKp-YAP1. Yeast cells containing PGKp-YAP1 were resistant to cycloheximide, a protein synthesis inhibitor, and also to cerulenin, a fatty acid synthesis inhibitor, but not to other drugs tested. The transformation efficiency of PGKp-YAP1 using cerulenin selection was comparable to that using a URA3 auxotrophic marker when low concentrations of cerulenin were used. Non-transformed drug-resistant colonies did appear on the low-concentration cerulenin plates. However, these non-transformed colonies could easily be identified, based on their cycloheximide sensitivity and/or their resistance to aureobasidin A to which the transformants were sensitive. Therefore, the dual drug resistance of PGKp-YAP1 could be used as an effective selection for PGKp-YAP1 recipient cells. The PGKp-YAP1 marker was used to disrupt the LYS2 gene and to transform an industrial yeast strain, indicating that this marker can be used for efficient and reliable gene manipulations in any Saccharomyces cerevisiae strain.     

Survey of switching techniques in high-speed networks and their performance

One of the most promising approaches for high speed networks for integrated service applications is fast packet switching, or ATM (asynchronous transfer mode). ATM can be characterized by very high speed transmission links and simple, hard-wired protocols within a network. To match the transmission speed of the network links, and to minimize the overhead due to the processing of network protocols, the switching of cells is done in hardware switching fabrics in ATM networks. A number of designs have been proposed for implementing ATM switches. Although many differences exist among the proposals, the vast majority of them are based on self-routeing multistage interconnection networks. This is because of the desirable features of multi-stage interconnection networks such as self-routeing capability and suitability for VLSI implementation. Existing ATM switch architectures can be classified into two major classes: blocking switches, where blockings of cells may occur within a switch when more than one cell contends for the same internal link, and non-blocking switches, where no internal blocking occurs. A large number of techniques have also been proposed to improve the performance of blocking and non-blocking switches. In this paper, we present an extensive survey of the existing proposals for ATM switch architectures, focusing on their performance issues.     

Adaptive control-based high-performance drive system implementation of traveling-wave-type ultrasonic motor

In recent years, ultrasonic motors (USM) as new actuators have attracted special interest. Several kinds of constructions and characteristics of USMs have been reported so far. Of these USMs, a traveling wave-type USM has many characteristics such as: high torque in the low-speed range, large holding torque based upon frictional force, flexible free forms, compactness in size and low magnetic noise. In practice, an inherent mechanical resonant frequency and a velocity amplitude of USM are changed largely according to operating temperature due to frictional drive, load disturbance torque, and applied voltage levels. Therefore, it is necessary to develop a new control system which solves these items and always supplies the required power with high efficiency and high performance in the practical applications. This paper proposes mainly a new sensorless high-performance control scheme of an inverter-fed ultrasonic motor, which is based on a control system technology with two feedbacks incorporating automatic resonant frequency tracking and constant velocity amplitude control strategies. This control system is realized in terms of a high-frequency chopper and a two-phase series/parallel resonant inverter. The experimental results are demonstrated and discussed compared with the theoretical ones.     

Sensorless control of synchronous reluctance motors using on‐line parameter identification method not affected by position estimation accuracy

This paper presents a novel on‐line parameter identification method for sensorless control of Synchronous Reluctance Motors (SynRMs). Although conventional sensorless control methods based on mathematical models usually need some complex measurements of motor parameters in advance, the proposed identification method does not require them and can be realized on‐line. The proposed method identifies motor parameters under sensorless control, so rotor position and velocity cannot be used to identify these parameters. However, the proposed method does not need rotor position and velocity, and identified parameters are not affected by these estimation errors. The sensorless control using identified motor parameters is realized, and the effectiveness of the proposed method is verified by experimental results. © 2006 Wiley Periodicals, Inc. Electr Eng Jpn, 155(3): 62–69, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20258     

Growth condition of iodine-doped n+-CdTe layers in metal-organic vapor phase epitaxy

Iodine doping of CdTe layers grown on (100) GaAs by metal-organic vapor phase epitaxy (MOVPE) was studied using diethyltelluride (DETe) and diisopropyltelluride (DiPTe) as tellurium precursors and ethyliodine (EI) as a dopant. Electron densities of doped layers increased gradually with decreasing the growth temperature from 425°C to 325°C. Doped layers grown with DETe had higher electron densities than those grown with DiPTe. When the hot-wall temperature was increased from 200°C to 250°C at the growth temperature of 325°C, doped layers grown with DETe showed an increase of the electron density from 3.7×10¹⁶ cm⁻³ to 2.6×10¹⁸ cm⁻³. On the other hand, such an increase of the electron density was not observed for layers grown with DiPTe. The mechanisms for different doping properties for DETe and DiPTe were studied on the basis of the growth characteristics for these precursors. Higher thermal stability of DETe than that of DiPTe was considered to cause the difference of doping properties. With increasing the hot-wall temperature from 200°C to 250°C, the effective ratio of Cd to Te species on the growth surface became larger for layers grown with DETe than those grown with DiPTe. This was considered to decrease the compensation of doped iodine and to increase the electron density of layers grown with DETe. The effective ratio of Cd to Te species on the growth surface also increased with decreasing growth temperature. This was considered to increase the electron density with decreasing growth temperature.     

Optical data storage by novel photoelectrochromic polymer

A novel elastic polymer containing 4,4′-bipyridinium salts with tetrakis[3,5-bis(trifluoromethyl)phenyl]borate as part of the main chain was synthesized. The cast film showed persistent and reversible colour changes due to photoinduced electron transfer upon excitation of an ion-pair charge-transfer band (_ex >365 nm) in vacuo. The lifetime of the coloured state markedly depended on temperature. The optically written data were stored without decay below 0°C and were erased thermally at elevated temperatures. The colour changes were reversibly repeatable for many times.     

An investigation of induced voltages to an underground gas pipeline from an overhead transmission line

This paper investigates induced voltage characteristics from an overhead transmission line by applying a method of modeling of induced voltages proposed by the authors. EMTP simulation results obtained by the modeling method agree with analytical results obtained from a well‐known formula. The induced voltages are significantly dependent on the configuration of the overhead line. A horizontal line induces the largest voltage in a gas pipeline, and the voltage induced by a vertical twin‐circuit line is about 20% smaller than that induced by a vertical single‐circuit line. The method is applied to a real pipeline system and the simulation results show reasonable agreement with field test results. © 2008 Wiley Periodicals, Inc. Electr Eng Jpn, 164(1): 43–51, 2008; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20465