Mechanical Properties of Single-Layer Diamond Reinforced Poly(vinyl alcohol) Nanocomposites through Atomistic Simulation

Low-dimensional carbon nanostructures are ideal nanofillers to reinforce the mechanical performance of polymer nanocomposites due to their excellent mechanical properties. Through molecular dynamics simulations, the mechanical performance of poly(vinyl alchohol) (PVA) nanocomposites reinforced with a single-layer diamond – diamane is investigated. It is found the PVA/diamane exhibits similar interfacial strengths and pull-out characteristics with the PVA/bilayer-graphene counterpart. Specifically, when the nanofiller is fully embedded in the nanocomposite, it is unable to deform simultaneously with the PVA matrix due to the weak interfacial load transfer efficiency, thus the enhancement effect is not significant. In comparison, diamane can effectively promote the tensile properties of the nanocomposite when it has a laminated structure as it deforms simultaneously with the matrix. With this configuration, the interlayer sp³ bonds endows diamane with a much higher resistance under compression and shear tests, thus the nanocomposite can reach very high compressive and shear stress. Overall, enhancement on the mechanical interlocking at the interface as triggered by surface functionalization is only effective for the fully embedded nanofiller. This work provides a fundamental understanding of the mechanical properties of PVA nanocomposites reinforced by diamane, which can shed lights on the design and preparation of next generation high-performance nanocomposites.     

Control of the particle microstructure during the synthesis of bulk-polymerized transparent methacrylate-acrylonitrile-butadiene-styrene resin

A series of methacrylate-acrylonitrile-butadiene-styrene (MABS) resins was prepared using bulk polymerization. The polarity of the continuous phase and the compatibility of two phases were changed by adjusting the methyl methacrylate (MMA) content, choosing values that were close to styrene-butadiene rubber solubility value. The possibility of controlling the microstructure of the MABS resin by changing the polarity of the components and the compatibility of two phases was assessed. The dynamic mechanical analysis shows that the compatibility of two phases varies with the MMA content. The morphological analysis shows that increasing MMA contents results in a gradual decrease in the sub-inclusion structure with a network skeleton of rubber particles, and that all the particles become solid rubber when the MMA content reaches 75%. The sub-inclusion structure reappears but does not have a network skeleton when the MMA content is 90%. The impact strength and morphological analysis indicate that the solid rubber particles and the sub-inclusion structure with a network skeleton provide excellent toughness, while the sub-inclusion structure without a network skeleton does not. In contrast, the transmittance of the ABS resin first increased and then decreased with increasing MMA content.     

Improving the initialization speed for long-range NRTK in network solution mode

Initialization speed is one of the most important factors in network real time kinematic (NRTK) performance. Owing to the low correlation among the error s     

Ni-Foam Structured Ni-Phyllosilicate Ensemble as an Efficient Monolithic Catalyst for CO2 Methanation

This work proposed a new path to synthesize Ni-phyllosilicate through the reaction of nickel hydroxide and silica sol on the surface of Ni-foam to form the monolithic Ni-phyllosilicate/Ni-foam catalyst. Ni-phyllosilicate could reprint the morphology of nickel hydroxid and firmly anchor on the framework of Ni-foam, which obtained fine Ni particles of 2.8 nm after reduction in H₂ at 650 °C, resulting in high catalytic activity for CO₂ methanation. In addition, the Ni-phyllosilicate/Ni-foam catalyst showed high long-term stability in a 100 h-lifetime test owing to the combined effects of surface confinement of Ni-phyllosilicate, firm anchoring between Ni-phyllosilicate and Ni-foam, as well as the high heat transfer property of Ni-foam.

Graphical Abstract

     

Chromium evaporation and oxidation characteristics of alumina-forming austenitic stainless steels for balance of plant applications in solid oxide fuel cells

The chromium (Cr) evaporation behavior of several different types of iron (Fe)-based AFA alloys and benchmark Cr₂O₃-forming Fe-based 310 and Ni-based 625 alloys was investigated for 500 h exposures at 800 °C to 900 °C in air with 10% H₂O. The Cr evaporation rates from alumina-forming austenitic (AFA) alloys were ~5 to 35 times lower than that of the Cr₂O₃-forming alloys depending on alloy and temperature. The Cr evaporation behavior was correlated with extensive characterization of the chemistry and microstructure of the oxide scales, which also revealed a degree of quartz tube Si contamination during the test. Long-term oxidation kinetics were also assessed at 800 to 1000 °C for up to 10,000 h in air with 10% H₂O to provide further guidance for SOFC BOP component alloy selection.     

Two-step method to deposit ZrO2 coating on carbon fiber: Preparation,characterization, and performance in SiC composites

Recently, ceramic matrix composites reinforced by short carbon fibers (CFs) attracted increasing attentions. To further improve mechanical properties and oxidation resistances, CFs were subjected to oxidation and acidification followed by sol-gel dip-coating to deposit ZrO₂ on their surfaces. ZrO₂-C_f/SiC composites were fabricated by joint hot compression molding and sintering, compared to C_f/SiC and SiC prepared by the same method. Microstructural analyses indicated that ZrO₂ coatings were successfully deposited on CF surfaces, formed strong bonding and interfaces between CF and the matrix. Meanwhile, CFs were found uniformly distributed in SiC matrix with random orientations. Flexural curves of ZrO₂-C_f/SiC and C_f/SiC revealed the presence of “false plasticity” regions after sharp drops, which were quite different from brittle flexural behavior of SiC ceramic. Compression strength of the three samples showed step-up growth. ZrO₂-C_f/SiC exhibited the highest value, indicating the introduction of CFs and ZrO₂ coatings do have great influence on mechanical performances. After heat treatment, ZrO₂-C_f/SiC exhibited better oxidation resistance than C_f/SiC, with weight loss ratios estimated to ??3.76% and ??6.43%, respectively. These improved properties indicated that ZrO₂-C_f/SiC would be excellent alternatives to other existence materials under ultra-high temperature environments.     

Investigation of machining and wear performance of various diamond micro-grinding tools

The International Journal of Advanced Manufacturing Technology - The wear of micro-grinding tools less than 1 mm in diameter is crucial for achieving acceptable surface quality and accurate...     

Corrosion behavior of Cu–Sn bronze alloys in simulated archeological soil media

The corrosion behavior of synthetic Cu–Sn bronze alloys with six different Sn contents was examined through an electrochemical test and a synthetic test in a simulated corrosive medium. The mechanism of corrosion and the morphology of the corroded surfaces were characterized through field emission scanning electron microscopy equipped with energy-dispersive spectroscopy. At the corrosion potential, the corrosion behavior appears to be determined by the charge transfer step and the diffusion process. It was found that the bronze-IV (Cu–26.8Sn) specimen exhibited the best corrosion resistance, as evidenced by a low corrosion current density and a high impedance. This improvement resulted from an increase in the content of the Cu–Sn solid solution in the alloy, which was conducive to forming a relatively more protective passive film on the surface of the bronze alloy. This finding would be valuable in the anticorrosion protection of archeological artefacts after their excavation.     

焉耆盆地原油物理化学特征及油源对比研究

在焉耆盆地侏罗系三工河组和八道湾组均发现原油,目前关于侏罗系产层原油的油源问题存在不同的认识。对研究区原油的物理、化学性质进行系统的研究,认为侏罗系三工河组和八道湾组原油不仅在物理性质上有一定的差别,而且在地球化学组成及生物标记化合物上也有一定的差异,应具有不同的来源。侏罗系三工河组原油属于典型腐殖型干酪根成因,而侏罗系八道湾组原油除了具有腐殖型干酪根成因的某些特征外,还具有湖相泥岩生烃的特点。通过原油与各类源岩生物标志物进一步对比分析发现,侏罗系三工河组原油与西山窑、三工河组烃源岩及石炭系、三叠系烃源岩地球化学特征均存在明显差异,与侏罗系八道湾组烃源岩对比性较好。侏罗系八道湾组原油与八道湾组、三叠系源岩有一定相似性,因此认为八道湾组源岩为其主要源岩,三叠系源岩也有一定的贡献。目前勘探生产主要以八道湾组烃源岩为目标,下一步应加强对三叠系烃源岩贡献区带的勘探部署。