排序方式: 共有26条查询结果,搜索用时 15 毫秒
1.
60CrMnMosteelisusedformakinghotrols.Thehotrolsexperiencealternatingmechanical,thermalandfrictionalloadduringroling.Itsbodyis... 相似文献
2.
26Cr2Ni4MoV转子钢的奥氏体再结晶及其消除组织遗传 总被引:2,自引:0,他引:2
以大型发电机及汽轮机转子用钢为对象,研究了奥氏体再结晶及消除组织遗传的原因,以及不同加热制度对奥氏体再结晶消除组织遗传的影响规律。 相似文献
3.
4.
高耐磨药芯焊丝堆焊组织及基体选择 总被引:1,自引:0,他引:1
制备了高铬铸铁型自保护药芯焊丝,并采用此焊丝分别在 Y-Ni4 铸铁、65Mn钢、40Cr 钢和灰口铸铁基体上进行堆焊.对不同堆焊试样进行硬度测试,对堆焊金属及其结合部位进行显微组织及断口形貌观察.结果表明,堆焊金属硬度在 60HRC 以上,断裂方式均为解理断裂.65Mn 钢堆焊试样熔合较好,且基本无裂纹,可在受冲击载荷较大的条件下使用;Y-Ni4 铸铁堆焊试样熔合良好,但在热影响区存在裂纹,应在冲击载荷较小或不受冲击载荷条件下使用;40Cr 和灰铸铁堆焊试样熔合不好,熔合区存在许多缺陷,不宜作为耐磨堆焊基体材料.Abstract: Four matrix materials, Y-Ni4 cast iron, 65Mn steel, 40Cr steel and grey cast iron, were hardfaced by the high chromium cast iron of self-shielded flux-cored wire separately. The hardness of different hardfacing specimens was measured, and the microstructures, fracture morphologies and the binding sites of different hardfacing specimens were observed. The results show that the hardness of the hardfacing metal is over 60 HRC and the fracture is of cleavage type. The fusion zones of 65Mn and Y-Ni4 hardfacing metal are good ones. However, the cracks can be observed in the heat-affected zone of Y-Ni4 hardfacing specimen. Therefore, the hardfacing metal of 65Mn steel is suitable for the condition of high stress wear and Y-Ni4 cast iron is suitable for the lower one. Besides, there are many defects in the fusion zone of 40Cr and grey cast iron hardfacing specimens, which are not suitable for the wear resistant matrix materials. 相似文献
5.
6.
一种新型锻钢冷轧工作辊材料 总被引:1,自引:0,他引:1
针对锻钢冷轧工作央含量高,轧辊淬硬层脆、利用率低的缺点,提高降碳、硅的新型轧辊材料。试验结果表明,含0.65%C的降碳、硅合金化新材料是一种适于工作条件恶劣、力学性能优良,使用寿命长的冷轧工作辊材料。 相似文献
7.
8.
以汽轮机转子用钢26Cr_2Ni_4M_oV为对象,研究了重复、阶梯两种不同热处理工艺对奥氏体自发再结晶的影响.结果表明,两种工艺均可书奥氏体晶粒由1级细化到7~8级。并试图解释试验中出现的某些现象。 相似文献
9.
采用搅拌摩擦加工制备SiC颗粒增强铝基复合材料,研究搅拌次数对复合层晶粒尺寸、硬度、拉伸及磨损性能的影响。结果表明,搅拌加工时添加SiC颗粒可提高复合层的硬度、耐磨性,但会降低其强度。随着搅拌次数的增加,复合材料硬度得到提高,添加SiC颗粒的试样经4道次搅拌后搅拌区平均硬度130 HV,而未添加颗粒时为118 HV。添加颗粒试样搅拌4次后,抗拉强度比搅拌1次试样强度明显提高,可达360.6 MPa,可达铝合金母材的68.5%。添加颗粒能够提高复合层的耐磨性,未添加颗粒时复合层摩擦系数为0.6,相比添加颗粒时仅为0.5。随着搅拌次数的增加,搅拌区晶粒细化程度得以提高,SiC颗粒分布更加均匀。 相似文献
10.