排序方式: 共有23条查询结果,搜索用时 31 毫秒
1.
贮氢合金Mg2Ni的燃烧合成 总被引:3,自引:1,他引:2
研究了燃烧合成贮氢合金Mg2 Ni的可行性以及保温时间和保温温度对合成产物的影响。结果证实燃烧合成了Mg2 Ni,并且确定Mg Ni的压坯试样的点火温度与Mg Ni系的共晶温度 (5 0 6℃ )很接近。 相似文献
2.
3.
5.
通过对M390粉末冶金不锈钢进行不同温度下的平衡相计算和真空气淬+低温回火处理,研究了淬火温度对回火后显微组织和力学性能的影响。结果表明,随着淬火温度的升高,M390钢回火后的碳化物尺寸不断长大,单位面积的颗粒数量减少而所占面积分数提高,碳化物分布均匀性降低。硬度随淬火温度的升高呈先上升后略微下降趋势,在1130 ℃淬火时达到最大值60.2 HRC,回火后降为58.5 HRC。抗弯强度受淬火温度的影响不大,为4000 MPa级水平。为获得良好性能,淬火温度应控制在1200 ℃以下,1130~1180 ℃真空气淬+200 ℃低温回火是刀剪用M390钢的最佳热处理工艺制度。 相似文献
6.
7.
研究了不同 Ti和B含量对H08C焊丝配合自主研发的高碱度焊剂所得熔敷金属冲击性能的影响,发现随着熔敷金属中Ti和B含量增加,熔敷金属的冲击性能都降低,尤其B,对冲击性能的不利影响远大于Ti. 相似文献
8.
碳化钛/钛镍金属间化合物复合涂层相组织研究 总被引:1,自引:0,他引:1
利用钛粉、镍粉和胶体石墨,真空条件下通过反应钎涂技术在低碳钢基体上制备了与基体冶金结合的碳化钛/钛镍金属间化合物复合涂层。采用扫描电子显微镜、能谱仪、X射线衍射仪及硬度计,研究了涂层的相组成、组织结构和成分分布。涂层组织由NiTi2、NiTi、TiC和hcp Ti组成,而涂层界面由NiTi和少量的hcp Ti构成,并且TiC主要分布在涂层中层。涂层中的NiTi2、NiTi、TiC是在钎涂过程中原位反应合成的,而且TiC和NiTi的量随碳含量的增加而增加。涂层表面硬度达到85HR15N,但不随TiC和NiTi含量增加而增高。 相似文献
9.
Fabrication of in-situ synthesized ceramic reinforced Ni-based alloy composite coatings by reactive braze coating processing 下载免费PDF全文
In-situ synthesized ceramic such as TiC, Cr7C3 and Cr5B3 reinforced Ni-based alloy composite coating was fabricated on the surface of mild steel substrate by reactive braze coating processing with colloidal graphite, Cr, Ni, ferro-boron, Si and titanium powders as the raw materials at low temperature of 1 000 ℃, and a new kind of coating materials was developed. By means of SEM, EDS, XRD and surface hardness tester, the microstructures, phases, hardness and wear-resistance of the coating were analyzed, respectively. The results revealed that the coating was mainly composed of the ceramic in-situ synthesized reinforcement phases of TiC, Cr7C3 and Cr5B3 and the binder phases in-situ synthesized of Ni31Si12 and (Ni, Fe) solid solution; The ceramic reinforcement phases of TiC, Cr7C3 and Cr5B3 were randomly distributed in the binder phases of Ni31Si12 and (Ni, Fe) solid solution; The coating had about 15vol% pores and can possibly be applied as a self-lubrication coating; The coating and the substrate were integrated together by metallurgical bonding; The coating had a hardness up to 91-94HR15N. 相似文献
10.
反应火焰喷涂TiC/Fe复合涂层组织及形成机理 总被引:1,自引:0,他引:1
以TiFe粉和碳的前驱体(石油沥青)为原料通过前驱体碳化复合技术制备了Ti-Fe-C系反应喷涂复合粉末,并用普通火焰喷涂技术制备了TiC/Fe陶瓷金属复合涂层.观测了喷涂粉末、淬熄实验获取的飞行粒子以及涂层的形态、相和组织结构.结果表明:前驱体碳化复合Ti-Fe-C系喷涂粉末有非常紧密的结构;可有效的解决反应喷涂过程中原料粉末分离的问题.在反应火焰喷涂过程中,每一个喷涂粉末颗粒构成独立的微小反应单元,原料之间反应充分.在整个喷涂过程中喷涂粉末经历了熔化扩散、物相形成、碰撞后快速凝固三个阶段.所得涂层由TiC和Ti2O3共生聚集片层和细小TiC颗粒弥散分布于金属基体所形成的内晶型复合强化片层交替叠加而成. 相似文献