Cathode plasma electrolytic deposition of Al2O3 coatings doped with SiC particles

Semiconductor particles doped Al₂O₃ coatings were prepared by cathode plasma electrolytic deposition in Al(NO₃)₃ electrolyte dispersed with SiC micro- and nano-particles (average particle sizes of 0.5–1.7?µm and 40?nm respectively). The effects of the concentrations and particle sizes of the SiC on the microstructures and tribological performances of the composite coatings were studied. In comparison with the case of dispersing with SiC microparticles, the dispersion of SiC nanoparticles in the coatings was more uniform. When the concentration of SiC nanoparticles was 5?g/L, the surface roughness of the composite coating was reduced by 63%, compared with that of the unmodified coating. Friction results demonstrated that the addition of 5?g/L SiC nanoparticles reduced the friction coefficient from 0.60 to 0.38 and decreased the wear volume under dry friction. The current density and bath voltage were measured to analyze the effects of SiC particles on the deposition process. The results showed that the SiC particles could alter the electrical behavior of the coatings during the deposition process, weaken the bombardment of the plasma, and improve the structures of the coatings.     

胡萝卜丁中维生素C在热风辅助射频干燥过程中降解的动力学模型

目的研究热风辅助射频(hot air-assisted radio frequency,HA-RF)干燥过程中维生素C随温度变化的降解动力学模型。方法在6.5 cm极板间距和60℃热风系统条件下进行HA-RF干燥,重点研究胡萝卜丁中维生素C在干燥过程中的降解动力学,包括脱氢抗坏血酸(dehydroascorbic acid,DHAA)和抗坏血酸(ascorbic acid,AA)。总维生素C含量采用2,4-硝基苯肼分光光度法测定,AA采用2,6-二氯吲哚酚滴定法测定。结果HA-RF干燥过程中维生素C的降解规律符合一级可逆模型,其降解活化能为40.54 kJ/mol。DHAA活化能为35.83 kJ/mol,表明DHAA的稳定性低于AA。结论本研究使用的干燥温度为62.5~77.5℃,较高的干燥温度下维生素C降解速率较高,较低处理温度下的降解过程具有更好的模型适应度(R2>0.98)。     

我国堆场磷石膏工程特性分析

磷石膏堆场的渗流及稳定性分析结果的可靠度取决于磷石膏物理力学参数的准确性,因此开展磷石膏工程特性研究十分必要。根据我国不同磷石膏堆场的试验数据,分别对磷石膏的物理性质、击实特性、渗透特性、固结特性和强度特性进行了分析。结果表明:磷石膏强度、压缩、渗透特性均与其压实程度密切相关,相同压实程度不同堆场磷石膏的物理力学性质相近;磷石膏渗透特性与其晶体形态有关;磷石膏在荷载作用下具有长期蠕变变形特性,磷石膏堆场封场后仍会发生较大沉降;深部磷石膏破坏时的应变大于浅层磷石膏;磷石膏剪切破坏时产生负孔隙水压力,实际工程中可通过测试孔压的变化了解堆场坝体的安全程度。     

一种分析碳酸盐岩孔隙系统数字图像的新方法

碳酸盐岩的孔隙类型多，孔径变化范围大，孔隙系统结构复杂，研究难度大。长期以来，是利用光学显微镜法、毛细管压力分析法、岩石孔隙系统复制法和图像分析仪法等方法或其中几种方法配合来研究碳酸盐岩孔隙系统。随着计算机图像技术的迅速发展和日益完善，借助该项技术通过碳酸盐岩孔隙系统数字图像来研究碳酸盐岩孔隙系统已经成为现实。文章提出一种研究碳酸盐岩孔隙系统数字图像的新方法。通过样品光薄片的光学显微镜（OM）数字图像和环境扫描电子显微镜（ESEM）数字图像二值化识别孔隙；构造孔隙度、孔隙贡献率和孔隙形状参数的计算公式用于数字图像分析，得到孔隙大小分布和孔隙形状分布。在此基础上，总结碳酸盐岩孔隙参数对其渗透率的控制作用。与传统的孔隙系统研究方法相比，该方法与计算机图像技术紧密结合，具有定量、快速的明显优势。     

高粘度指数润滑油生产工艺探讨

详细介绍了中国石油抚顺石化分公司石油一厂新区以沈阳、大庆混合原油的减二、减三线馏分油为原料,采用甲苯、甲乙酮脱蜡、糠醛精制、白土补充精制工艺生产HVI润滑油基础油的生产经验。并结合理论分析,提出了完善此类工艺的一系列建议。生产HVI200基础油,要求蒸馏减二线润滑油馏分粘度不大于4.75 mm2/s,脱蜡油粘度不大于56 mm2/s。为保证HVI200基础油粘度指数合格,要降低减二线馏分中多环环烷烃含量。     

提高深井硬地层钻井速度技术难点及对策

乌龙1井地层为南方海相沉积,地层古老、岩石硬度大、研磨性强、可钻性差、地层倾角大(最大为80°)井斜难以控制、蹩跳钻严重,制约了该地区深井钻井速度。文章介绍了解决提高钻井速度这一瓶颈问题,从深井优快钻井及其配套技术、硬地层钻进的钻头优选、优化钻井参数、引用新技术、新工艺、新工具等方面进行了探索,钻井速度有了大幅度地提高,对类似井具有一定的借鉴作用。     

基于形态学top-hat算子的多传感器图像融合

本文根据形态学top-hat算子能够提取图像中极大值与极小值区域的特点,将其应用于多传感器图像融合的两个重要领域——多聚焦图像融合和高分辨、多光谱图像融合.实验中将本文方法与Laplacian塔型变换、子波变换、主分量分析等方法进行了比较,结果表明本文所提的基于top-hat算子的融合方法具有优越的性能,拓广了top-hat算子的应用范围.     

Determination of molecular weight and molecular sizes of polymers by high temperature gel permeation chromatography with a static and dynamic laser light scattering detector

Flow-mode static and dynamic laser light scattering (SLS/DLS) studies of polymers, including polystyrene, polyethylene, polypropylene and poly(dimethylsiloxane) (PDMS), in 1,2,4-trichlorobenzene (TCB) at 150 °C were performed on a high temperature gel permeation chromatography (GPC) coupled with a SLS/DLS detector. Both absolute molecular weight (M) and molecular sizes (radius of gyration, R_g and hydrodynamic radius, R_h) of polymers eluting from the GPC columns were obtained simultaneously. The conformation of different polymers in TCB at 150 °C were discussed according to the scaling relationships between R_g, R_h and M and the ρ-ratio (ρ=R_g/R_h). Flow-mode DLS results of PDMS were verified by batch-mode DLS study of the same sample. The presented technique was proved to be a convenient and quick method to study the shape and conformation of polymers in solution at high temperature. However, the flow-mode DLS was only applicable for high molecular weight polymers with a higher refractive index increment such as PDMS.     

On Finding the Multicast Protection Tree Considering SRLG in WDM Optical Networks

In this letter, a new sharing mechanism, SRLG sharing, is proposed, which allows the links of the same shared risk link group (SRLG) in a primary light tree to share protections in WDM optical networks. In previous studies, how to share spare resources with SRLG constraints has not been studied in multicast optical networks. In this letter, considering SRLG sharing, we propose a novel algorithm –multicast with SRLG sharing (MSS)– to establish a protection light tree. Finally, the algorithm MSS and the algorithm multicast with no SRLG sharing (MNSS) are compared through a simulation to show that our new sharing scheme of SRLG sharing is more efficient than that of no SRLG sharing in terms of spare resource utilization and blocking probability.     

ZnGa2O4纳米晶的制备和结构表征

采用喷射共沉淀法制备了ZnGa2O4 纳米晶，XRD、SEM和TEM结构分析结果表明，喷射共沉淀法制备的ZnGa2O4的纳米晶颗粒细小均匀，形状完整，与化学共沉淀法相比，粒子尺寸明显减小，小于10nm，同时ZnO杂相峰消失，分析了喷射共沉淀法的机理，并对实验结果进行了解释。