Environmental-stress-screening using degradation measurements

ESS (environmental stress screening) has been extensively used to reduce infant mortality by precipitating defects. The existing ESS plans precipitate defects by stressing all products for specified durations. The plans usually require long screen durations to allow nearly all defective items to fail, and thus generate excessive aging effects on good items. For some products, failures are defined in terms of performance characteristics exceeding their critical values. This paper describes the principles of using degradation measurements of performance characteristics to screen the products. In an ESS, the performance characteristics of defective items degrade considerably faster than those of good ones, yielding a bimodal distribution of the characteristics. As screen duration increases, the 2 modes of the distribution shift apart. It is possible to find a tightened critical value to weed out the defective items before they fail. This paper, based on these principles, further designs the optimal 2-level screen plans which minimize a segment of life-cycle cost and which simultaneously meet the reliability requirement. The minimum cost is achieved by choosing optimal part-level and unit-level screen durations and tightened critical values of parts. A numerical example is followed by discussion. Because the ESS regime of this paper allows defective parts to be screened out before they fail, the developed optimal ESS plans can reduce life-cycle cost, shorten part-level screen duration, and alleviate aging effects on good products     

宝钢2300 mm宽厚板连铸机扇形段的质量控制

扇形段是连铸机组中的主要设备,扇形段制造水平的高低将直接影响到板坯厚度的均匀性,对最终的钢板轧制质量起着十分重要的作用。阐述扇形段主要部件的质量控制。     

Distributed Optical Fiber Sensor for Multi-point Temperature Measurement

The distributed optical fiber sensing technology is overviewed, which is based on Raman scattering light theory. Basic operation principle, structure, system characteristics and signal processing are discussed. This structure and method of the signal processing possess of certain spatial resolution, hence will ensure the practicability of system.     

气动冲击器研究现状及发展趋势

阐述了气动冲击旋转钻井用气动冲击器国内外近期的研究现状,以及各类冲击器的结构和性能参数,并提出了气动冲击器的发展趋势。     

全球电信界的战略联盟

９０年代初，随着通信向全球化方向发展，发达国家各电信企业纷纷采用联盟的方式，相互联合，发挥各自优势，大举进军全球电信市场。面对这种联盟潮流，想要搭上全球通信的列车，发展中国家应该采取什么措施？坚持什么原则？本文作者对此进行了较深入的分析和研究，并对中国电信的发展提出了建议。     

基于子结构法的升船机主传动系统的动力学建模

用动态子结构法对三峡升船机的主传动系统建立动力学模型。把整个系统分为8个一级子系统,每个一级子系统又分为4个二级子系统,建立每个二级子系统的动力学模型,利用边界条件,层层组装,最后组合成完整的动力学方程。     

超纯汞生产新工艺的技术研究

本文着重介绍了超纯汞生产新工艺的基本原理的理论探讨及生产工艺过程的控制。     

S7-1200利用高速脉冲输出方式实现打印

本文介绍SIEMENS S7-1200利用高数脉冲（Pulse Train Output,PTO）功能与MCU进行通讯的方法,具体介绍其中的一个应用：用PTO实现S7-1200的字符打印输出。     

基于AROP程序包的类Landsat遥感影像配准与正射纠正试验和精度分析

遥感影像的精确配准和正射纠正是进行图像融合、变化检测、图像镶嵌、定量遥感建模、多时相和多传感器影像协同应用的基础和前提。以美国国家航空和航天管理局下设LEDAPS(Landsat Ecosystem Disturbance Adaptive Processing System)课题组开发的配准与正射纠正程序包AROP(Automated Registration and Orthorectification Package)为例,详细阐述了其配准的原理与程序设计流程,并对其配准的精度进行了分析和评价。试验表明:AROP程序包算法能够找出足够的控制点,且控制点分布较为均匀,配准误差小于0.5个像元。误差特征表现为:扫描误差明显大于航向误差,误差的结果与影像漂移、DEM、坡度存在一定的相关性,高程和坡度是影响配准精度的主要因素之一。该程序包目前能够用于对我国CBERS影像的正射校正以及波段不匹配处理,但是对HJ卫星CCD影像数据配准还有待于进一步研究。     

碱激发剂对地聚物固化黄土工程特性的影响

为了解决传统的黄土固化剂强度耐久性及环保性差的问题,通过击实试验、无侧限抗压强度试验、直剪试验和崩解试验研究了不同模数和波美度的水玻璃碱激发粉煤灰基地聚物固化黄土的工程特性,结合扫描电镜(scanning electron microscope,SEM)、物理吸附试验分析了固化黄土的微观结构.试验表明:随着水玻璃模数降低、波美度增大,固化黄土最优含水率线性降低,最大干密度增加,且模数较波美度对击实特性的影响更显著;固化黄土的抗压强度增大,黏聚力增大.1.5模数、30°Bé时抗压强度为3.42 MPa,黏聚力为548.17 kPa;同时,崩解性减弱,吸水性降低;微观结构上,水玻璃碱激发粉煤灰生成的硅铝酸钠等凝胶产物包裹充填于土颗粒间,相互胶结形成空间网状结构,改善了孔径分布与孔隙结构.水玻璃模数越小、波美度越高,固化黄土的平均孔径越小,比表面积越大,2～4 nm的纳米级孔隙体积越大.