10 Gbit/s optical soliton transmission over 7200 km by using amonolithically integrated MQW-DFB-LD/MQW-EA modulator light source

The authors demonstrate 10 Gbit/s optical soliton transmission in a recirculating loop through the use of a monolithically integrated MQW-DFB-LD/MQW-EA modulator light source. The timing jitter due to the Gordon-Haus effect is successfully reduced by the optical bandpass filters conventionally used in the cascaded EDFAs to avoid the accumulation of amplified spontaneous emission. The transmission distance of 7200 km is achieved at a bit error rate of 10^-9     

Cyclic GMP inhibits and shifts the activation curve of the delayed-rectifier (I[K1]) of type I mammalian vestibular hair cells

NITRIC oxide (NO) plays a role in the modulation of the predominant potassium current of type I vestibular hair cells, a low-voltage activated current called I(K1). Since many effects of NO are mediated via cGMP, patch-clamp recordings were made to evaluate the effects of cGMP on I(K1). In whole-cell recordings 1 mM cGMP shifted Vhalf of I(K1) by 15.0 +/- 2.4 mV (n = 6) to more positive. In cell-attached 'multichannel' recordings 1 mM 8-bromo-cGMP caused a reversible shift of Vhalf by 13.8 +/- 2.6 mV (n = 12) and in single channel recordings in the cell-attached configuration the open probability was reduced at -60 mV from 0.39 +/- 0.14 to 0.08 +/- 0.01. cGMP had no effect on excised inside-out patches, indicating that an intact cytosolic milieu with functioning phosphorylation cascades is necessary. cGMP seems to be an important second messenger which reduces the potassium conductance of vestibular hair cells.     

A cavity-backed rectangular aperture antenna with application to a tilted fan beam array antenna

A rectangular aperture of A/sub x//spl times/A/sub y/, cut in the top conducting plate of a triplate transmission line and backed by a cavity, radiates a tilted beam off the direction normal to the aperture. The mechanism of the radiation is explained using the Poynting vector distribution above the aperture and the phase distribution of the electric field over the aperture. The tilt angle is calculated as a function of side length A/sub x/ for a representative value of A/sub y/=18 mm=0.747/spl lambda//sub 12.45/, where /spl lambda//sub 12.45/ is the wavelength at a test frequency of 12.45 GHz. A tilted beam of approximately 27/spl deg/ is realized at A/sub x//A/sub y/=8/9 with a gain of approximately 8 dB. Using this value of A/sub x//A/sub y/, an array antenna composed of rectangular cavity-backed aperture elements is investigated. The array forms a tilted fan beam without phase shifters. The frequency responses of the gain and input impedance are discussed.     

Hydrodynamic interaction and coalescence of two droplets under large step shear strains

We observed change in distance between two droplets in each step after application of large multi-step shear strains. Experiments were performed using a sliding plate apparatus. Large step shear strains were applied to two polyisobutylene droplets in poly(dimethyl siloxane) matrix in the same plane between the plates. The distance between the two droplets decreases with increasing the total shear strain, which is given by the product of the step strain magnitude and the number of application of the step strains. The two droplets coalesce when the distance becomes less than the diameter of the droplets. The slope for plots of the distance versus the total strain is independent of the step strain magnitude. This indicates that the effect per unit strain on the distance is the same, irrespective of the strain magnitude. It is suggested that a stronger hydrodynamic interaction between the droplets is the main cause for the droplet approach.     

Suppression of photo-induced dilation in cyanide treated hydrogenated amorphous silicon films

Effects of cyanide (CN) treatment with hydrogenated amorphous silicon (a-Si:H) films have been investigated. The decrease of ΔV/V was observed in cyanide treated a-Si:H films and the successive thermal annealing at 200°C after CN treatment induced the further reduction of the ΔV/V. XPS spectra show the indirect evidence that the cyanide species is present within 10 nm from the hydrogenated amorphous silicon surface. The results of CN treatment with a-Si:H solar cells are demonstrated.     

Effect of Microstructural Control on Thermoelectric Properties of Hot-Pressed Aluminum-Doped Zinc Oxide

The thermal conductivity of polycrystalline Al-doped ZnO was controlled through the fabrication of nanostructured polycrystalline materials, by hot-pressing nanosized Zn_{1– x} Al _x O ( x = 0.01, 0.02) particles, which were synthesized by a coprecipitation and spray-drying method. This process resulted in an improved thermoelectric power factor because of the nanosized Zn_0.99Al_0.01O particles of the polycrystalline products. The thermal conductivity also was decreased as a result of the formation of nanocrystalline Zn_0.99Al_0.01O.     

The polymerization and copolymerization of nitroalkyl acrylates and nitroalkyl methacrylates

Nitroalkyl acrylates and methacrylates involving some new compounds were prepared. The homopolymerization of these monomers in toluene and their copolymerization with styrene in acetone were carried out with azobisisobutyronitrile as initiator. The rate of polymerization of the nitroalkyl acrylates showed a correlation with the number of nitro groups situated on the ester side chain. The apparent activation energies of the polymerization were found to be 22.0–27.5 kcal./mole for the nitroalkyl acrylates and about 11.5–13.0 kcal./mole for the nitroalkyl methacrylates. From the reactivity ratios and Q-e values of the copolymerization the following information was obtained. The copolymerization behavior of nitroalkyl acrylates and methacrylates showed an alternating tendency, and these monomers belong to the conjugative monomer groups. On the reactivities of these monomers, the polarity of vinyl group was affected a little by nitro group of ester bond side, and the resonance affected little. These monomers were crosslinked with 2-methyl-2-nitro-1,3-propylene diacrylate. Some of the polymers showed marked improvement in the physical properties of elastomers.     

Dynamic Power Integrity Control of ATE for Eliminating Overkills and Underkills in Device Testing

This paper proposes a power integrity control technique for dynamically controlling power supply voltage fluctuations for a device under test (DUT), and demonstrates its effectiveness for eliminating the overkills/underkills due to the difference of power supply impedance between an automatic test equipment (ATE) and a practical operating environment of the DUT. The proposed method injects compensation currents into the power supply nodes on the ATE system in a feed-forward manner such that the ATE power supply waveform matches with the one on the customer’s operating environment of the DUT. A method for calculating the compensation current is also described. Experimental results show that the proposed method can emulate the power supply voltage waveform under a customer’s operating condition and eliminate 95 % of overkills/underkills in the maximum operating frequency testing with 105 real silicon devices. Limitations and applications of the proposed method are also discussed.