OTDM transmitter using WDM-TDM conversion with an electroabsorptionwavelength converter

An all-optical multiplexing technique using wavelength division multiplexing (WDM)-time division multiplexing (TDM) conversion with an electroabsorption wavelength converter has been proposed and demonstrated. The effectiveness of this WDM-TDM conversion technique for various pulsewidth settings was experimentally investigated. The fluctuation of the signal performance, which was inevitably caused by the coherent crosstalk between adjacent pulses in the conventional optical time division multiplexing (OTDM) technique, were successfully suppressed, even in the case of wide pulse duration. High Q-factor performance has been maintained for a wide range of duty ration from 36% to 74%. By introducing this technique to the optical time division multiplexer, a highly stable and high-quality 40-Gb/s optical signal can be effectively produced without generating the short pulse or setting two tributaries at orthogonal polarization states, and without introducing high-speed electronics for signal multiplexing. The WDM-TDM conversion with an electroabsorption wavelength converter was extended to 60-Gb/s operation by using three 20-Gb/s tributaries. A clear eye opening was confirmed for a waveform after the WDM-TDM conversion of the 60-Gb/s signal     

A sensorless brushless dc motor system

This paper describes a brushless dc motor system without position or speed sensor. The brushless motor consists of a permanent magnet synchronous motor and a voltage-source inverter capable of controlling the amplitude and frequency of voltage. The rectangular-shaped stator current with a conducting interval of 120° (electrical) is controlled to be in phase with the trapezoidal back electromotive force. This results in producing maximum torque. Variable speed is achieved by adjusting the average motor voltage similarly to chopper control of dc motors. In this paper, two sensorless position detecting methods, i.e., an “indirect method” suited for the lower-speed range and a “direct method” suited for the higher-speed range are proposed. The combination of the two makes it possible to detect the rotor position over a wide-speed range. Furthermore, a speed-sen-sorless PLL control is proposed in applying the principle of the direct method. Experimental results obtained from a prototype brushless dc motor are shown to confirm the validity of the sensorless drive. The starting procedure of the motor also is discussed because it is impossible to detect the rotor position at a standstill.     

Simulation study of eutrophication in Hiroshima Bay: Simulation of particulate and dissolved organic matter using cyclic transformation of carbon

A phytoplankton model, which includes a carbon cycle combined with a constant current obtained by the computation of tidal currents, was applied to the coastal region (Hiroshima Bay, Japan). The transformation rate constants for the carbon cycle were experimentally evaluated.The seasonal variations of particulate and dissolved organic matter by the simulation model were reasonably consistent with the field data. Carbon concentration increased by primary production in the upper layer was approx. 10 times that augmented by loading of carbon from land at the shore in summer. Sinking plays an important role in the elimination of particulate organic matter. On the other hand, horizontal advection and turbulent diffusion are important factors for the diminution of dissolved organic matter.     

Generalized measuring-worm algorithm: high-accuracy mapping and movement via cooperating swarm robots

Recently, many extensive studies have been conducted on robot control via self-positioning estimation techniques. In the simultaneous localization and mapping (SLAM) method, which is one approach to self-positioning estimation, robots generally use both autonomous position information from internal sensors and observed information on external landmarks. SLAM can yield higher accuracy positioning estimations depending on the number of landmarks; however, this technique involves a degree of uncertainty and has a high computational cost, because it utilizes image processing to detect and recognize landmarks. To overcome this problem, we propose a state-of-the-art method called a generalized measuring-worm (GMW) algorithm for map creation and position estimation, which uses multiple cooperating robots that serve as moving landmarks for each other. This approach allows problems of uncertainty and computational cost to be overcome, because a robot must find only a simple two-dimensional marker rather than feature-point landmarks. In the GMW method, the robots are given a two-dimensional marker of known shape and size and use a front-positioned camera to determine the marker distance and direction. The robots use this information to estimate each other’s positions and to calibrate their movement. To evaluate the proposed method experimentally, we fabricated two real robots and observed their behavior in an indoor environment. The experimental results revealed that the distance measurement and control error could be reduced to less than 3 %.     

Quantitative structural analysis of twin boundary in alpha-Zn7Sb2O12 using HAADF STEM method

The structure and composition of the 1/4{110} twin boundary in alpha-Zn7Sb2O12 have been determined by using quantitative high-angle annular dark field scanning transmission electron microscopy (HAADF STEM) analysis. The noise in the experimental HAADF STEM images is reduced by using the maximum entropy method and average processing, and the parameters used in dynamical simulations are experimentally determined. From the analysis, it has been found that octahedral sites in the twin boundary slightly shift parallel to the [110] direction, and a reduction of the Sb concentration at the octahedral sites on the plane adjacent to the twin boundary was detected. The reduction was measured from three regions in the same twin boundary, and the Sb concentrations were 4 +/- 3, 8 +/- 3 and 19 +/-2 at% from 33 at%.     

Induction and intracellular localization of a 72-kDa heat shock protein in rat gastric mucosa after water-immersion stress

We investigated the expression and changes in the intracellular localization of a 72-kDa heat shock protein (HSP72) in rat gastric pyloric and fundic mucosa before and after water-immersion stress. Severe mucosal damage was found in the fundic mucosal area of the stomach after this stress. However, no mucosal lesion developed in the pyloric mucosal area. HSP72 in both the soluble and insoluble fractions of the pyloric and the fundic mucosal areas was significantly increased after water-immersion stress, peaking 6h after the initiation of the stress. The increase in HSP72 was more significant in the pyloric mucosal area than in the fundic mucosal area under both normal and stress conditions. The increase of HSP72 in the pyloric mucosal cells occurred prior to the formation of the mucosal lesions, whereas the increase of HSP72 in the fundic mucosal cells was observed after ulcer formation. An immunohistochemical study showed that HSP72 was constitutively expressed in the cytoplasm of the gastric mucosal cells, and that the intranuclear induction of HSP72 was remarkably intense in the pyloric mucosal cells, especially in the proliferative zone, compared with the fundic mucosal cells. Our results may suggest that HSP72 has an important cytoprotective function in gastric mucosal cells and that there is a "biophysical" difference between pyloric and the fundic mucosal cells.     

Development of a pulse control-type MEMS microrobot with a hardware neural network

This article presents the micro-electro-mechanical systems (MEMS) microrobot which demonstrates locomotion controlled by hardware neural networks (HNN). The size of the microrobot fabricated by the MEMS technology is 4 × 4 × 3.5 mm. The frame of the robot is made of silicon wafer, and it is equipped with a rotary-type actuator, a link mechanism, and six legs. The rotary-type actuator generates rotational movement by applying an electrical current to artificial muscle wires. The locomotion of the microrobot is obtained by the rotation of the rotary-type actuator. As in a living organism, the HNN realized robot control without using any software programs, A/D converters, or additional driving circuits. A central pattern generator (CPG) model was implemented as an HNN system to emulate the locomotion pattern. The MEMS microrobot emulated the locomotion method and the neural networks of an insect with the rotary-type actuator, the link mechanism, and the HNN. The microrobot performed forward and backward locomotion, and also changed direction by inputting an external trigger pulse. The locomotion speed was 0.325 mm/s and the step width was 1.3 mm.     

Extremely localized interaction in a market model

The model of self-organized criticality (SOC) is a useful tool to understand the complexity of natural systems in the form of the artificial life and the artificial market. However, SOC remains the question what guarantees the criticality even though the natural systems seem to keep itself in the critical state. In this paper, we focus on the locality of interaction in zero-intelligence plus (ZIP) model. The extremely localized interaction changes the behavior of the ZIP model from equilibrium to intermittency. Although the original ZIP model falls into unstable with some noise, extremely localized interaction model archives robust intermittency against the noise parameter. Further, the statistical property of intermittent behavior shows the power-law nature.     

Study of Superconducting Fault Current Limiter Using Vacuum Interrupter Driven by Electromagnetic Repulsion Force for Commutating Switch

Using a high-temperature superconductor, we constructed and tested a model superconducting fault current limiter (SFCL). The superconductor and the vacuum interrupter as the commutation switch were connected in parallel using a bypass coil. When the fault current flows in this equipment, the superconductor is quenched and the current is transferred to the parallel coil because of the voltage drop in the superconductor. This large current in the parallel coil actuates the magnetic repulsion mechanism of the vacuum interrupter. Due to the opening of the vacuum interrupter, the current in the superconductor is broken. By using this equipment, the current flow time in the superconductor can be easily minimized. On the other hand, the fault current is also easily limited by large reactance of the parallel coil     

Current-induced domain nucleation in ferromagnet

A key mechanism of the current-induced magnetization dynamics is the spin torque from a spin polarized current (spin current), which couples to spatial gradient of magnetization. Recently, it was pointed out that a large spin current applied to a uniform ferromagnet leads to a spin-wave instability. In this paper, we show that such instability is absent in a state containing a domain wall. This may indicate that nucleation of magnetic domains occurs above a certain critical spin current. This scenario is supported by an explicit energy comparison between the uniformly magnetized state and the domain-wall state under spin current.